Snapper specifications Mower Deck Maintenance, How to Check the Fuel Filter

Page 30

How to Check the Fuel Filter

NOTE: Before you replace the fuel filter or the fuel line, the fuel tank must be empty.

If the fuel filter is dirty, the engine will run rough and have less performance. Remove the old filter (Figure 31). Replace the old filter with a new filter. Use an original equipment part. See an authorized service dealer in your area.

A

B

B

A

C

Figure 31: Fuel filter

A - Fuel line

B - Clips

C - Fuel filter (example only)

Check the Tires

Check the air pressure in the tires. Tires with too much air pressure will cause the unit to ride rough. Also, the wrong air pressure will keep the mower deck from cutting level.

Recommended air pressure is 14 PSI (1 BAR) for both front and rear tires.

Mower Deck Maintenance

How to Remove the Mower Deck (42” Models)

1.Move the blade rotation control to the DISENGAGE position.

2.If equipped, remove the gauge wheels.

3.Open the deck level position cover, and move the deck lift lever to the level adjustment position (Figure 32).

WARNING: The deck lift lever is spring loaded. Make sure the deck lift lever is locked in the LEVEL ADJUSTMENT position.

4.Remove the hair pins and the washers from the adjuster arms (Figure 33). See illustrations “C” and “D”.

5.Remove the hair pins and washers from the suspension links. See illustrations “A” and “B”.

English

Figure 32: Deck lift lever

A - Deck level position cover (partially hidden) B - Deck level adjustment position

6.Remove the end of the blade engage cable housing from the blade engage cable bracket, then unhook the cable spring from the mower deck idler. See illustration “E”.

7.Disconnect the front hanger from the axle support. See illustration “F”.

8.Remove the mower drive belt from the stack pulley.

9.Pull the mower deck away from the right side of the unit.

10.To operate without the mower deck, move the deck lift lever to the TOP position.

How to Install the Mower Deck (42” Models)

1.Push the mower deck under the right side of the unit.

2.Put the mower drive belt around the stack pulley. Make sure the “V” side of the mower drive belt is against the stack pulley. Also, make sure the mower drive belt is not twisted.

3.Attach the front hanger to the axle support with the hanger rod. Fasten with the fasteners as shown. See illustration “F”.

4.Make sure the mower drive belt is between the stack pulley and the two belt guides. See illustration “G”.

5.Attach the suspension links to the lifter assembly. Fasten with the washers and hair pins. See illustrations “A” and “B”.

6.Attach the right and the left adjuster arms to the suspension brackets. Fasten with the washers and hair pins. See illustrations “C” and “D”.

7.Hook the blade engage cable spring onto the deck idler, and firmly press the end of the blade engage cable housing into the blade engage cable bracket. See illustration “E”.

8.Move the blade rotation control to the ENGAGE position. Make sure the mower drive belt is inside all the belt guides.

9.Make sure the mower deck is level. See the instructions on “How To Level The Mower Deck”.

28

www.snapper.com

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Lawn Tractor Series Where to Find Us Mower EngineDate Purchased Table of Contents Preparation Protection for ChildrenProtection against Tipovers Do not allow pre-teenage children to operate machineSafe Handling of Gasoline Towing International Pictorials GhijAssembly Parts Bag ContentsInstalling the Seat Assembling the Steering WheelMaintenance Free Battery How to Install the Battery CablesIMPORTANT! Before You Start Mowing Remove the protective cap from the battery terminalHow To Check The Safety Interlock Switches Operator Presence System SeatHow to Prepare the Engine Check the TiresCheck the Level of the Mower Deck Features and Controls How to Engage the Blades 42 Models Using ControlsHow to Use the Throttle Control OperationHow to Engage the Blades 46 & 52 models How to Use the Speed Control PedalDriving and Stopping the Unit How to Change Direction How to Use the Cruise ControlHow to Drive in Reverse Push the brake pedalHow to Set the Parking Brake How to Change the Cutting HeightHow to Stop the Unit Remove the key to restrict access to the RMO feature How to Transport the UnitHow to Operate the Mower Deck MowingHow to Operate the Unit on Hills How to Stop on a HillHow to Start Operation on a Hill Before Starting the Engine Check the Oil How to Start the EngineEngine Operation Add GasolineMowing and Bagging Tips TipsOperating Tips Use the left side of the mower deck to trim near an objectFrequency Maintenance Required Comments MaintenanceMaintenance Schedule Maintenance engine Examine bladesGeneral Recommendations How to Check the MufflerHow to Remove and Install the Blade InspectionAdjustments How to Sharpen the BladeHow to Adjust the Blade Rotation Control 42 Models Blade engage cable adjustment Blade engage cable bracket How to Check and Adjust the PTO Clutch 46 & 52 Models Blade Brake Check 46 & 52 Models OnlyHow to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHow to Charge the Battery How to Remove the BatteryHow to Clean the Battery Before you charge the battery, remove the batteryWhere to Lubricate LubricationHow to Install the Mower Deck 42 Models Mower Deck MaintenanceHow to Check the Fuel Filter Remove the mower drive belt from the stack pulleyMower driver belt V Belt guide Stack pulley How to Remove the Mower Deck 46 & 52 Models How to Install the Mower Deck 46 & 52 ModelsHanger rod Q Adjuster arm How to Adjust the Gauge Wheels How to Level the Mower DeckRemove the gauge wheels Figure Loosening adjuster knobs Lift link Adjuster knobs Replacing the Motion Drive BeltHow to Replace the Mower Drive Belt 42 Models English How to Replace the Primary Mower Drive Belt 46 & 52 Models Remove the primary mower drive belt from the stack pulleyEnglish How to Install the Wheels How to Replace the FuseFasten the rear wheel with washer and e-ring Storage over 30 days Troubleshooting Troubleshooting ChartCut level Pedal is depressed When the brake pedal isCorrectly Mower blades will notSpecifications Product SpecificationsEnglish English Year Limited Warranty Snapper Products Macon Street McDonough, GA

SLT23460 LT195420, CLT195420, LT23460, CLT23460, LT24520, CLT24520, SLT23460, SLT24520, CLT195420, LT23460, CLT23460, LT24520, LT195420, CLT195420,, LT23460, CLT23460, LT24520, CLT24520, SLT23460, SLT24520, CSLT23460, CSLT24520, SLT23460FC, SLT24520FC, LT195420, CLT195420, LT23460, CLT23460, LT24520, CSLT24520, SLT23460, SLT24520, CSLT23460, CSLT24520, SLT23460FC, SLT24520FC, LT195420, CLT195420, LT23460, CLT23460, LT24520, CLT24520, SLT23460, SLT24520, CSLT23460, CSLT24520, SLT23460FC, SLT24520FC, LT195420, CLT195420,, LT23460, CLT23460, LT24520, CLT24520, SLT23460, SLT24520, CSLT23460, CSLT24520 specifications

The Snapper lawn mower series, including models like LT195420, CLT195420, LT23460, CLT23460, LT24520, CLT24520, SLT23460, SLT24520, CSLT23460, CSLT24520, SLT23460FC, and SLT24520FC, showcases innovative features designed to provide convenience, performance, and efficiency in lawn care solutions. These mowers are particularly notable for their robust engineering and adaptability to various mowing conditions.

One of the key characteristics of the Snapper LT and CLT series is their powerful engine options. Each model is equipped with high-performance engines that ensure reliable starting, effective cutting power, and efficient fuel consumption. The LT195420 and CLT195420 models, for instance, feature a 19-inch cutting deck that enhances maneuverability and provides impressive cutting precision in tighter spaces.

The LT23460 and CLT23460 models, with their larger 23-inch cutting decks, cater to users looking for faster mowing capabilities without sacrificing quality. These mowers also incorporate a unique three-in-one cutting system, allowing users to choose between mulching, side discharge, or bagging clippings, depending on the lawn care needs.

The SLT and CSLT series take user comfort and ease of operation to the next level. These models feature ergonomically designed handles and comfortable seat systems that can be adjusted to suit the user's height, ensuring a pleasant mowing experience. Additionally, the SLT24520FC and SLT23460FC versions come with enhanced features for those who desire a more versatile approach to lawn maintenance.

Snapper’s commitment to innovation is evident in the incorporation of advanced technologies, including electric start capabilities and dual-blade cutting systems. This design maximizes cutting efficiency and results in a cleaner, more even finish on the lawn.

Durability is another hallmark of the Snapper mower lineup, with heavy-duty steel construction used in most models to ensure longevity, even in challenging mowing conditions. The series also includes features for easy maintenance, such as accessible oil and air filter locations, allowing homeowners to perform routine upkeep without hassle.

In summary, the Snapper LT195420, CLT195420, LT23460, CLT23460, LT24520, CLT24520, SLT23460, SLT24520, CSLT23460, CSLT24520, SLT23460FC, and SLT24520FC models are engineered for both performance and user convenience. Their combination of powerful engines, innovative cutting systems, and ergonomic designs make them an excellent choice for anyone looking to maintain a pristine lawn with ease and efficiency.
Top Page Image Contents