Snapper CZT19481KWV important safety instructions Operating Instructions

Page 11

Section 3 - OPERATING INSTRUCTIONS

ROLL RELEASE: To roll the machine without the engine running, pressure within the hydraulic pumps must be released. There is a hydraulic pressure relief valve on the upper side of each pump that is used to release the pressure. Use a wrench to rotate both relief valves counter clockwise two full turns to open. After rolling machine, both relief valves must be rotated clockwise to close valves and tighten securely before operating machine. Machine will not move if relief valves are open. See Figure 3.4.

3.2STARTING & STOPPING - ENGINE, BLADES, PARKING BRAKE

3.2.1. STARTING ENGINE

When the ignition key is turned the engine will not start or turn over unless the blade switch is pushed in to the "OFF" position and the motion control levers are in the neutral lock position. Always engage parking brake before starting engine.

1.Complete pre-start checklist.

2.Sit in operator's seat.

3.Push blade switch in to "OFF", blades disengaged position and engage parking brake. See Figure 3.2.

4.Move choke control forward to choke position to start a cold engine. See Figure 3.5.

5.Move engine speed control to the Rabbit "FAST" position. See Figure 3.5.

6.Turn key to the start position until engine starts. See Figure 3.6.

NOTE: If after 5 seconds of cranking the engine does not start, release the key. Attempt starting again after waiting for approximately 20 seconds.

7.After engine starts, move the choke control to the "OFF" or no choke position. Allow a brief warm-up until engine runs smooth.

ROTATE RELIEF VALVE

 

 

 

 

COUNTERCLOCKWISE TO

CHOKE

 

 

 

ENGINE SPEED

 

 

RELIEVE PRESSURE

 

 

CONTROL

CONTROL

 

KEY SWITCH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MOTION CONTROL

 

 

 

 

 

 

LEVERS SHOWN IN

 

 

 

 

 

 

THE NEUTRAL

 

 

RELIEF VALVE

 

 

 

 

 

 

LOCK POSITION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SHOWN FROM OPERATOR'S VIEW POINT

 

FIGURE 3.4

 

 

FIGURE 3.5

 

 

 

 

 

 

 

 

 

 

 

 

!

WARNING

!

 

 

 

DO NOT disengage the hydro transmission and coast down slopes. DO NOT use Roll Release Control to disengage the hydro transmission unless machine motion can be controlled and engine is off.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Commercial MID-MOUNT Zero Turning Hydro Drive Series From Previous Column Important Safety InstructionsSafe Handling of Gasoline From Previous TowingTable of Contents Nomenclature FamiliarizationIntroduction Safety Messages and Symbols Safety Messages and Symbols Roll BAR Protective Structure Decals PRE-START Check List Operating InstructionsOperating Instructions Parking Brake Stopping EngineStarting Mower Blades Stopping Mower BladesDriving Machine Cutting Height AdjustmentOPERATION- Motion Controls Engine Must not Start if Safety Interlock System ChecksStopping Machine Folding the Roll BAR Protective StructureCheck Mower Blade Maintenanceoperating InstructionsService After First 5 Hours Deck shown with discharge raised Check Mower Drive Belt 1. Lower deck to lowest settingAfter Every 25 Operating Hours 4.3.1. Engine Mower Components 1. Mower Drive BeltEngine Riding Mower Lubrication 1. Front Wheel BearingsBefore Operating Machine Annually END of Each SeasonDeck Removal Maintenanceoperating Instructions Neutral Position Adjustments ADJUSTMENTSOPERAINGINSTRUCTIONS& RepairSide to Side and Front to Rear Neutral Position Adjustments From PreviousMower Deck & Component Adjustments Mower Deck Adjustment LevelnessParking Brake Adjustment Traction Belt Tension Traction Belt ReplacementTracking Adjustment Belt Removal Belt ReplacementBelt Adjustment Mower Drive Belt Replacement and AdjustmentBlade Sharpening Battery Charging 10BATTERY Battery RemovalBattery Installation State of Charge Digital Voltmeter Battery Testing11HYDRAULIC SYSTEM, Purging Problem Probable Cause Corrective Action SectionTROUBLESHOOTING3 Operating InstructionsCutting Grass Performed USE HRS Season SERVICEection3 SCHEDULE- OP Rating InstructionsService REF. Number Each 100Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Commercial MID-MOUNT Zero Turning Hydro Drive Series
Related manuals
Manual 40 pages 5.07 Kb

CZT19481KWV specifications

The Snapper CZT19481KWV is a powerful and versatile lawn mower that combines strength and efficiency to deliver exceptional performance for both residential and commercial landscaping needs. Designed with attention to detail and advanced technology, this mower stands out in its category, making lawn care both easier and more enjoyable.

At the heart of the Snapper CZT19481KWV is its robust 19.5 HP Briggs & Stratton engine, known for its reliability and impressive power output. This engine ensures smooth and consistent cutting performance on a variety of terrains, from flat lawns to hilly landscapes. Additionally, its Easy Start feature allows users to fire up the mower with minimal effort, transforming what could be a cumbersome task into a quick and straightforward experience.

One of the standout features of the CZT19481KWV is its zero-turn technology, which provides unparalleled maneuverability. This design allows the operator to make sharp turns and navigate around obstacles with ease, significantly reducing mowing time. With a cutting width of 48 inches, this mower efficiently tackles large areas while maintaining precision.

The mower comes equipped with a heavy-duty steel deck that ensures durability and long-lasting performance. Its robust construction minimizes the chances of wear and tear, even when faced with tough mowing conditions. The deck also features a 3-in-1 cutting system, allowing users to choose between bagging, mulching, or side discharging grass clippings, providing flexibility based on lawn care preferences.

User comfort is a priority with the Snapper CZT19481KWV. It features an adjustable high-back seat, which provides excellent support and reduces fatigue during long mowing sessions. The ergonomically designed controls are easy to reach and operate, ensuring that users can maintain focus on the task at hand without distraction.

In terms of maintenance, the Snapper CZT19481KWV is designed for simplicity. Features like an easy-access oil drain and large fuel tank reduce the hassle often associated with lawn mower upkeep. Its compact design makes it easy to store, while the stylish aesthetics give it a modern touch that will appeal to a wide range of users.

With its combination of impressive features, durable construction, and user-friendly design, the Snapper CZT19481KWV is an excellent choice for those looking to elevate their lawn care experience, delivering results that are both professional and aesthetically pleasing. Whether maintaining a sprawling landscape or a simple backyard, this mower is equipped to handle it all with efficiency and ease.
Top Page Image Contents