Snapper CZT19481KWV Neutral Position Adjustments From Previous, Mower Deck Adjustment Levelness

Page 21

Section 53 - ADJUSTMENTSOPERAINGINSTRUCTIONS& REPAIR

5.1NEUTRAL POSITION ADJUSTMENTS (Continued From Previous Page)

12. With motion control levers remaining in the neutral lock position, See Figure 3.7, hold connecting rod up to the activation assembly and check length of rod. Tie rod end bolt must align with the activation assembly. If bolt is not aligned with the activation assembly, adjust tie rod. Loosen jam nut that secures tie rod. Rotate tie rod in or out to align with hole in activation assembly. Repeat step for other hydro pump. See Figure 5.4.

5.2 MOWER DECK & COMPONENT ADJUSTMENTS

5.2.1. MOWER DECK ADJUSTMENT (LEVELNESS)

SIDE to SIDE and FRONT to REAR

Before making deck leveling adjustments, inflate rear

tires to 12 PSI and front tires to 25 PSI. When adjust-

ed correctly, the deck will be level side to side within

1/8", have a low cut setting of approximately 1", and

the blades pitched approximately 3/16" higher at the

rear.

1. Place machine on a smooth level surface.

2. Check side to side level by rotating blades until tips

are pointing to the sides of the deck. Check the meas-

HYDRO PUMP ACTIVATION ASSEMBLY

TIE ROD END

HYDRO

PUMP

TIE ROD END

BOLT IS SHOWN

MISALIGNED

WITH ACTIVATION

ASSEMBLY

LOOSEN NUT AND ROTATE TIE ROD END IN OR OUT TO ALIGN WITH ACTIVATION ASSEMBLY

urement of outside blade tips to the ground on both

blades. The measurement of each of the outside blade

tips should be within 1/8" of each other. If measure-

ment of the blade tips is not within 1/8", adjustment

should be made.

3. Move deck lift lever and set the mower deck to the

highest cutting position.

4. Place 1" blocks under the front and rear edge of the

mower deck.

5. Move deck lift lever and set the mower deck to the

lowest cutting position.

6. Loosen the nuts and bolts that secure both front

deck support chains. Adjust chains until tight and

retighten bolts and nuts. Torque to 20 to 30 ft. lbs. See

Figure 5.5.

FRONT

LIFT ARM

CHAIN

BOLT IS SHOWN ALIGNED WITH HOLE

DECK HANGER BRACKET

LOOSEN BOLT AND NUT,

TIGHTEN CHAIN, SECURE

BOLT AND NUT

FIGURE 5.5

FIGURE 5.4

13.Once tie rod end bolt is aligned with activation assembly insert into hole and reinstall washers and nut that secure bolt to assembly. Tighten securely. Tighten tie rod jam nut securely.

14.Start engine, disengage parking brake, and check rotation of the rear wheels.

15.Reinstall both hydro pump fans. Reinstall washer and bolt. Tighten bolt securely.

16.Reinstall screen and tighten retaining hardware securely.

7.Loosen the nuts that secure both rear deck support eyebolts. Adjust to remove slack from both rear chains. Tighten nuts securely. See Figure 5.6.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Commercial MID-MOUNT Zero Turning Hydro Drive Series From Previous Column Important Safety InstructionsSafe Handling of Gasoline From Previous TowingTable of Contents Familiarization IntroductionNomenclature Safety Messages and Symbols Safety Messages and Symbols Roll BAR Protective Structure Decals PRE-START Check List Operating InstructionsOperating Instructions Starting Mower Blades Stopping EngineStopping Mower Blades Parking BrakeCutting Height Adjustment OPERATION- Motion ControlsDriving Machine Stopping Machine Safety Interlock System ChecksFolding the Roll BAR Protective Structure Engine Must not Start ifMaintenanceoperating Instructions Service After First 5 HoursCheck Mower Blade After Every 25 Operating Hours 4.3.1. Engine Check Mower Drive Belt 1. Lower deck to lowest settingMower Components 1. Mower Drive Belt Deck shown with discharge raisedBefore Operating Machine Riding Mower Lubrication 1. Front Wheel BearingsAnnually END of Each Season EngineDeck Removal Maintenanceoperating Instructions Neutral Position Adjustments ADJUSTMENTSOPERAINGINSTRUCTIONS& RepairMower Deck & Component Adjustments Neutral Position Adjustments From PreviousMower Deck Adjustment Levelness Side to Side and Front to RearParking Brake Adjustment Traction Belt Replacement Tracking AdjustmentTraction Belt Tension Belt Adjustment Belt ReplacementMower Drive Belt Replacement and Adjustment Belt RemovalBlade Sharpening 10BATTERY Battery Removal Battery InstallationBattery Charging State of Charge Digital Voltmeter Battery Testing11HYDRAULIC SYSTEM, Purging Problem Probable Cause Corrective Action SectionTROUBLESHOOTING3 Operating InstructionsCutting Grass Service REF. Number Each SERVICEection3 SCHEDULE- OP Rating Instructions100 Performed USE HRS SeasonDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Commercial MID-MOUNT Zero Turning Hydro Drive Series
Related manuals
Manual 40 pages 5.07 Kb

CZT19481KWV specifications

The Snapper CZT19481KWV is a powerful and versatile lawn mower that combines strength and efficiency to deliver exceptional performance for both residential and commercial landscaping needs. Designed with attention to detail and advanced technology, this mower stands out in its category, making lawn care both easier and more enjoyable.

At the heart of the Snapper CZT19481KWV is its robust 19.5 HP Briggs & Stratton engine, known for its reliability and impressive power output. This engine ensures smooth and consistent cutting performance on a variety of terrains, from flat lawns to hilly landscapes. Additionally, its Easy Start feature allows users to fire up the mower with minimal effort, transforming what could be a cumbersome task into a quick and straightforward experience.

One of the standout features of the CZT19481KWV is its zero-turn technology, which provides unparalleled maneuverability. This design allows the operator to make sharp turns and navigate around obstacles with ease, significantly reducing mowing time. With a cutting width of 48 inches, this mower efficiently tackles large areas while maintaining precision.

The mower comes equipped with a heavy-duty steel deck that ensures durability and long-lasting performance. Its robust construction minimizes the chances of wear and tear, even when faced with tough mowing conditions. The deck also features a 3-in-1 cutting system, allowing users to choose between bagging, mulching, or side discharging grass clippings, providing flexibility based on lawn care preferences.

User comfort is a priority with the Snapper CZT19481KWV. It features an adjustable high-back seat, which provides excellent support and reduces fatigue during long mowing sessions. The ergonomically designed controls are easy to reach and operate, ensuring that users can maintain focus on the task at hand without distraction.

In terms of maintenance, the Snapper CZT19481KWV is designed for simplicity. Features like an easy-access oil drain and large fuel tank reduce the hassle often associated with lawn mower upkeep. Its compact design makes it easy to store, while the stylish aesthetics give it a modern touch that will appeal to a wide range of users.

With its combination of impressive features, durable construction, and user-friendly design, the Snapper CZT19481KWV is an excellent choice for those looking to elevate their lawn care experience, delivering results that are both professional and aesthetically pleasing. Whether maintaining a sprawling landscape or a simple backyard, this mower is equipped to handle it all with efficiency and ease.
Top Page Image Contents