Snapper CZT19481KWV important safety instructions Belt Replacement, Belt Adjustment, Belt Removal

Page 24

Section 53 - ADJUSTMENTSOPERAINGINSTRUCTIONS& REPAIR

LOOSEN BOLTS,

SLIDE PLATE TO

MAKE MACHINE

TRACK STRAIGHT

TRACKING

ADJUSTMENT

PLATE

RIGHT SIDE

LOOSEN BOLTS, ALIGN

MOTION CONTROL

3.

Remove old mower drive belt. Note the belt routing.

See Figure 5.13.

5.7.2. BELT REPLACEMENT

1.

Route new belt around blade pulleys, idler pulley,

and clutch pulley in the same position as old belt was

removed. See Figure 5.13.

2.

Reconnect deck idler tensioning rod as previously

removed. Refer to Section 'Belt Adjustment' below for

proper belt tension adjustment.

3.

Reinstall power unit footrest.

5.7.3.

BELT ADJUSTMENT

LEVER BLOCK

HANDLEBARS AS IN FIGURE 5.12a

To adjust belt tension, loosen jam nut on deck idler tensioning rod, then adjust inner nut in or out until idler

FIGURE 5.12

5.6aMOTION LEVER HANDLEBAR ALIGNMENT

Handlebars of both left and right Motion Control Levers should be aligned when levers are dropped from their neutral lock positions. See Figure 5.12a. If bars are not aligned:

1.Loosen bolts that secure handlebar adjustment brackets to lever blocks, and adjust handlebars until aligned. See Figure 5.12. Retighten bolts after align- ment is achieved.

2.Note that handlebars are adjustable, and can be raised or lowered to provide optimum operator com- fort. Simply remove hardware securing handlebars to handlebar adjustment brackets, raise or lower bars, and replace hardware.

ALIGN HANDLEBARS

RAISE OR

 

LOWER BARS

 

DROP LEVERS FROM

 

REMOVE

NEUTRAL POSITION

HARDWARE

 

 

 

spring measures 2-5/16". See Figure 5.13a. Tighten jam nut against inner nut after adjustment is achieved.

RIGHT

PULLEY

CENTER

PULLEYELECTRIC CLUTCH

MOWER

DRIVE

BELT

LEFT

 

PULLEY

BELT ROUTING

FIGURE 5.13

FIGURE 5.12a

5.7MOWER DRIVE BELT REPLACEMENT AND ADJUSTMENT

Inspect mower drive belt. Replace belt if it shows signs of excessive wear, damage and/or is broken.

5.7.1.

BELT REMOVAL

1.

Remove power unit footrest.

2.

Remove jam nut, inner nut, washers and spring

from front threads of deck idler tensioning rod. See

Figure 5.13a. Slip rod out of deck bracket, and swivel

AFTER REPLACING BELT, REPLACE SPRING, WASHERS AND INNER NUT, AND TIGHTEN UNTIL SPRING LENGTH IS 2-5/16”. THEN INSTALL JAM NUT AND TIGHTEN AGAINST INNER NUT.

TO REMOVE BELT, REMOVE JAM NUT AND INNER NUT, WASHERS AND SPRING

2-5/16”

deck idler pulley back.

FIGURE 5.13a

24

Image 24
Contents Commercial MID-MOUNT Zero Turning Hydro Drive Series Important Safety Instructions From Previous ColumnSafe Handling of Gasoline Towing From PreviousTable of Contents Familiarization IntroductionNomenclature Safety Messages and Symbols Safety Messages and Symbols Roll BAR Protective Structure Decals Operating Instructions PRE-START Check ListOperating Instructions Stopping Engine Starting Mower BladesStopping Mower Blades Parking BrakeCutting Height Adjustment OPERATION- Motion ControlsDriving Machine Safety Interlock System Checks Stopping MachineFolding the Roll BAR Protective Structure Engine Must not Start ifMaintenanceoperating Instructions Service After First 5 HoursCheck Mower Blade Check Mower Drive Belt 1. Lower deck to lowest setting After Every 25 Operating Hours 4.3.1. EngineMower Components 1. Mower Drive Belt Deck shown with discharge raisedRiding Mower Lubrication 1. Front Wheel Bearings Before Operating MachineAnnually END of Each Season EngineDeck Removal Maintenanceoperating Instructions ADJUSTMENTSOPERAINGINSTRUCTIONS& Repair Neutral Position AdjustmentsNeutral Position Adjustments From Previous Mower Deck & Component AdjustmentsMower Deck Adjustment Levelness Side to Side and Front to RearParking Brake Adjustment Traction Belt Replacement Tracking AdjustmentTraction Belt Tension Belt Replacement Belt AdjustmentMower Drive Belt Replacement and Adjustment Belt RemovalBlade Sharpening 10BATTERY Battery Removal Battery InstallationBattery Charging Battery Testing State of Charge Digital Voltmeter11HYDRAULIC SYSTEM, Purging SectionTROUBLESHOOTING3 Operating Instructions Problem Probable Cause Corrective ActionCutting Grass SERVICEection3 SCHEDULE- OP Rating Instructions Service REF. Number Each100 Performed USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Commercial MID-MOUNT Zero Turning Hydro Drive Series
Related manuals
Manual 40 pages 5.07 Kb

CZT19481KWV specifications

The Snapper CZT19481KWV is a powerful and versatile lawn mower that combines strength and efficiency to deliver exceptional performance for both residential and commercial landscaping needs. Designed with attention to detail and advanced technology, this mower stands out in its category, making lawn care both easier and more enjoyable.

At the heart of the Snapper CZT19481KWV is its robust 19.5 HP Briggs & Stratton engine, known for its reliability and impressive power output. This engine ensures smooth and consistent cutting performance on a variety of terrains, from flat lawns to hilly landscapes. Additionally, its Easy Start feature allows users to fire up the mower with minimal effort, transforming what could be a cumbersome task into a quick and straightforward experience.

One of the standout features of the CZT19481KWV is its zero-turn technology, which provides unparalleled maneuverability. This design allows the operator to make sharp turns and navigate around obstacles with ease, significantly reducing mowing time. With a cutting width of 48 inches, this mower efficiently tackles large areas while maintaining precision.

The mower comes equipped with a heavy-duty steel deck that ensures durability and long-lasting performance. Its robust construction minimizes the chances of wear and tear, even when faced with tough mowing conditions. The deck also features a 3-in-1 cutting system, allowing users to choose between bagging, mulching, or side discharging grass clippings, providing flexibility based on lawn care preferences.

User comfort is a priority with the Snapper CZT19481KWV. It features an adjustable high-back seat, which provides excellent support and reduces fatigue during long mowing sessions. The ergonomically designed controls are easy to reach and operate, ensuring that users can maintain focus on the task at hand without distraction.

In terms of maintenance, the Snapper CZT19481KWV is designed for simplicity. Features like an easy-access oil drain and large fuel tank reduce the hassle often associated with lawn mower upkeep. Its compact design makes it easy to store, while the stylish aesthetics give it a modern touch that will appeal to a wide range of users.

With its combination of impressive features, durable construction, and user-friendly design, the Snapper CZT19481KWV is an excellent choice for those looking to elevate their lawn care experience, delivering results that are both professional and aesthetically pleasing. Whether maintaining a sprawling landscape or a simple backyard, this mower is equipped to handle it all with efficiency and ease.