Snapper CZT19481KWV important safety instructions Towing, From Previous

Page 4

!

IMPORTANT SAFETY INSTRUCTIONS

!

OPERATION

(Continued From Previous Page)

16.On slopes, the weight of the towed equipment may cause loss of traction and loss of control. When towing, travel slowly and allow extra distance to stop.

17.DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, a deadly poi- son.

18.DO NOT discharge material against a wall or obstruction. Material may ricochet back towards the operator.

19.Only use accessories approved by the manufacturer. See manufacturer's instructions for proper operation and installation of accessories.

TOWING

1.Tow only with a machine that has a hitch designed for towing. DO NOT attach towed equipment except at the hitch point.

2.Follow the manufacturer's recommendation for weight limits for towed equipment and towing on slopes.

3.DO NOT allow children or others on towed equipment.

4.On slopes, the weight of the towed equipment may cause loss of traction and loss of control.

5.Travel slowly and allow extra distance to stop.

MAINTENANCE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of chil- dren in a well ventilated, unoccupied building.

2.Keep engine free of grass, leaves or excess grease to reduce fire hazard and engine overheating.

MAINTENANCE

(Continued From Previous Column)

3.When draining fuel tank, drain fuel into an approved con- tainer outdoors and away from open flame.

4.Check brakes frequently; adjust, repair or replace as needed.

5.Keep all bolts, nuts and screws properly tight. Check that all cotter pins are in proper position.

6.Always provide adequate ventilation when running engine. Exhaust gases contain carbon monoxide, an odorless and deadly poison.

7.Disconnect negative (black) cable from battery before performing maintenance or service. Cranking engine could cause injury.

8.DO NOT work under machine without safety blocks.

9.Service engine and make adjustments only when engine is stopped. Remove spark plug wire(s) from spark plug(s) and secure wire(s) away from spark plug(s).

10.DO NOT change engine governor speed settings or over- speed engine.

11.Lubricate machine at intervals specified in manual to pre- vent controls from binding.

12.Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when han- dling them.

13.DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.

14.Have machine serviced by an authorized SNAPPER deal- er at least once a year and have the dealer install any new safety devices.

15.Maintain or replace safety and instruction labels as nec- essary.

16.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

!

WARNING

!

Grass Catcher bags used on SNAPPER products are made of woven fabric, and are subject to deterioration and wear during nor- mal usage. Check condition of bags before each use. Immediately replace worn or damaged catcher bags with only bags recom- mended by SNAPPER. The Grass Catcher is optional equipment on some models.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Commercial MID-MOUNT Zero Turning Hydro Drive Series Important Safety Instructions From Previous ColumnSafe Handling of Gasoline Towing From PreviousTable of Contents Introduction FamiliarizationNomenclature Safety Messages and Symbols Safety Messages and Symbols Roll BAR Protective Structure Decals Operating Instructions PRE-START Check ListOperating Instructions Stopping Engine Starting Mower BladesStopping Mower Blades Parking BrakeOPERATION- Motion Controls Cutting Height AdjustmentDriving Machine Safety Interlock System Checks Stopping MachineFolding the Roll BAR Protective Structure Engine Must not Start ifService After First 5 Hours Maintenanceoperating InstructionsCheck Mower Blade Check Mower Drive Belt 1. Lower deck to lowest setting After Every 25 Operating Hours 4.3.1. EngineMower Components 1. Mower Drive Belt Deck shown with discharge raisedRiding Mower Lubrication 1. Front Wheel Bearings Before Operating MachineAnnually END of Each Season EngineDeck Removal Maintenanceoperating Instructions ADJUSTMENTSOPERAINGINSTRUCTIONS& Repair Neutral Position AdjustmentsNeutral Position Adjustments From Previous Mower Deck & Component AdjustmentsMower Deck Adjustment Levelness Side to Side and Front to RearParking Brake Adjustment Tracking Adjustment Traction Belt ReplacementTraction Belt Tension Belt Replacement Belt AdjustmentMower Drive Belt Replacement and Adjustment Belt RemovalBlade Sharpening Battery Installation 10BATTERY Battery RemovalBattery Charging Battery Testing State of Charge Digital Voltmeter11HYDRAULIC SYSTEM, Purging SectionTROUBLESHOOTING3 Operating Instructions Problem Probable Cause Corrective ActionCutting Grass SERVICEection3 SCHEDULE- OP Rating Instructions Service REF. Number Each100 Performed USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Commercial MID-MOUNT Zero Turning Hydro Drive Series
Related manuals
Manual 40 pages 5.07 Kb

CZT19481KWV specifications

The Snapper CZT19481KWV is a powerful and versatile lawn mower that combines strength and efficiency to deliver exceptional performance for both residential and commercial landscaping needs. Designed with attention to detail and advanced technology, this mower stands out in its category, making lawn care both easier and more enjoyable.

At the heart of the Snapper CZT19481KWV is its robust 19.5 HP Briggs & Stratton engine, known for its reliability and impressive power output. This engine ensures smooth and consistent cutting performance on a variety of terrains, from flat lawns to hilly landscapes. Additionally, its Easy Start feature allows users to fire up the mower with minimal effort, transforming what could be a cumbersome task into a quick and straightforward experience.

One of the standout features of the CZT19481KWV is its zero-turn technology, which provides unparalleled maneuverability. This design allows the operator to make sharp turns and navigate around obstacles with ease, significantly reducing mowing time. With a cutting width of 48 inches, this mower efficiently tackles large areas while maintaining precision.

The mower comes equipped with a heavy-duty steel deck that ensures durability and long-lasting performance. Its robust construction minimizes the chances of wear and tear, even when faced with tough mowing conditions. The deck also features a 3-in-1 cutting system, allowing users to choose between bagging, mulching, or side discharging grass clippings, providing flexibility based on lawn care preferences.

User comfort is a priority with the Snapper CZT19481KWV. It features an adjustable high-back seat, which provides excellent support and reduces fatigue during long mowing sessions. The ergonomically designed controls are easy to reach and operate, ensuring that users can maintain focus on the task at hand without distraction.

In terms of maintenance, the Snapper CZT19481KWV is designed for simplicity. Features like an easy-access oil drain and large fuel tank reduce the hassle often associated with lawn mower upkeep. Its compact design makes it easy to store, while the stylish aesthetics give it a modern touch that will appeal to a wide range of users.

With its combination of impressive features, durable construction, and user-friendly design, the Snapper CZT19481KWV is an excellent choice for those looking to elevate their lawn care experience, delivering results that are both professional and aesthetically pleasing. Whether maintaining a sprawling landscape or a simple backyard, this mower is equipped to handle it all with efficiency and ease.
Top Page Image Contents