Snapper 24 HP manual Mowing Recommendations, Height of Grass, Cut Here On First Pass Second

Page 21

MOWING

Before mowing, set the cutting height as described in the Troubleshooting, Adjustments & Service section.

1.Engage the parking brake. Make sure the PTO switch is disengaged and the motion control lever is in the NEUTRAL position.

2.Start the engine (see STARTING THE ENGINE).

3.Set the throttle to FULL.

4.Engage the PTO by pulling up on the PTO switch.

5.Begin mowing. See Mowing Recommendations section for tips on mowing patterns and lawn care. See Trouble Shooting section for information on trouble shooting common cutting problems.

6.When finished, shut off the PTO.

7.Stop the engine (see STOPPING THE TRACTOR AND ENGINE).

MOWING RECOMMENDATIONS

Several factors can affect how well your machine cuts grass, Following proper mowing recommendations can improve the performance and life of your machine.

Height of Grass

Often cutting height is a matter of personal preference. Typically, you should mow the grass when it is is between three and five inches high. The proper cutting height range for a specific lawn will depend upon several factors, including the type of grass, the amount of rainfall, the prevailing temperature, and the lawn’s overall condition.

Cutting the grass too short causes weak, thin grass plants, which are easily damaged by dry periods and pests. Cutting too short is often more damaging than allowing the grass to be slightly higher.

Letting grass grow a bit longer—especially when it is hot and dry—reduces heat build-up, preserves needed moisture and protects the grass from heat damage and other problems. However, allowing grass to grow too high can cause thin turf and additional problems.

Cutting off too much at one time shocks the plant’s growth system and weakens the grass plants. A good rule of thumb is the 1/3 rule: to cut no more than one third of the grass height, and never more than 1 inch at a time.

The amount of grass you are able to cut in one pass is also effected by the type of mowing system you are using (for example, broadcasting with side discharge decks can process a much larger volume of grass than mulching does).

Operation

Figure 12. Proper Cutting Height

Tall Grass Requires Incremental Cutting

For extremely tall grass, set the cutting height at maximum for the first pass, and then reset it to the desired height and mow a second or third time.

Don’t cover the grass surface with a heavy layer of clippings. Consider using a grass collection system and starting a compost pile.

Cut Here On

 

 

Cut

First Pass

 

 

Here On

 

 

 

 

Second

 

 

 

 

Pass

 

 

 

Figure 13. Incremental Cutting

Operation

19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 24HP Zero-Turn Riders OPERATOR’S ManualDate Purchased Table of Contents Safety Rules & Information Operating SafetySlope Operation Retaining Walls, Drop-offs, and Water General Operation Slope Operation Safety Rules and InformationSafe Handling of Gasoline Service & MaintenanceIdentification Numbers Safety Decals Safety DecalsNorth American Models CE Export ModelsNorth American Models only Safety Interlock System Safety Interlock SystemExport Models only Safety Interlock System Operational Safety ChecksNorth American Safety Icons Safety IconsCE Export Safety Icons ServicingControl Functions Features & ControlsSeat Adjustment Lever PTO SwitchHour Meter Transmission Oil FillGeneral Operating Safety OperationChecks Before Starting Starting the Engine Stopping the Rider and EnginePushing the Rider by Hand Smooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerExecuting Turns TurningMower Removal Installation InstallationRemoval Mowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods When and How Often to MowMowing Patterns Proper Broadcast MowingProper Mulching Attaching a TrailerRegular Maintenance Before Every Spring Each Hours 100 200 Fall UseCheck Transmission Oil Change Transmission Oil Filter Grease LubricationOil Arm PivotServicing the Mower Blades Removing the Mower BladeInspecting the Mower Blades Sharpening the Mower Blade Reinstalling the Mower BladesBalancing the Mower Blades NailAdding Fuel Check Tire PressuresFuel Filter Tire PressureChange Engine OIL & Filter Engine MaintenanceCheck / Fill Transmission OIL Transmission OIL Filter ChangeChange Interval Every 200 Hours Battery Maintenance Cleaning the Battery and CablesStorage Troubleshooting the Rider Troubleshooting, Adjustments, & ServiceTroubleshooting the Mower Troubleshooting, Adjustments, & ServiceStreaking Troubleshooting Common Cutting ProblemsSeat Adjustment Ground Speed Control Lever AdjustmentSeat Position Adjustment Speed Balancing Adjustment Cutting Height AdjustmentNeutral Adjustment Suspension Adjustment A. Front Shock Adjustment Collar Parking Brake AdjustmentBlade Brake Check PTO Clutch AdjustmentOrient Blades Side-to-Side Mower Deck LevelingRoller BAR Leveling Select Models Mower Belt ReplacementBattery Charging Hydraulic Pump Drive Belt ReplacementTechnical Manuals SpecificationsPage Belts and Blades Tractor Product Quick Specs

24 HP specifications

The Snapper 24 HP is a powerful and reliable riding lawn mower designed to tackle large lawns and challenging terrains with ease. With its robust engine and advanced features, it offers a premium mowing experience for homeowners and professionals alike.

At the heart of the Snapper 24 HP is a dependable 24 horsepower (HP) Briggs & Stratton engine. This high-performance engine provides ample power to efficiently cut through thick grass and maintain exhilarating speed while mowing. The engine is equipped with an overhead valve design, promoting better fuel efficiency and lower emissions, making it an environmentally friendly option.

One of the standout features of the Snapper 24 HP is its 42-inch cutting deck, which provides a wide cutting path for improved mowing efficiency. The deck is made from durable steel, designed to withstand the rigors of regular use, while also ensuring a clean and precise cut. It offers multiple cutting height adjustments, allowing users to customize their lawn's height from 1.5 to 4 inches, catering to various grass types and seasonal needs.

Additionally, the Snapper 24 HP comes with a hydrostatic transmission system that allows for smooth forward and reverse operation. This technology not only enhances maneuverability but also makes it easier to navigate obstacles such as trees and garden beds without the need for constant gear shifting. As a result, users can enjoy a more efficient mowing experience while reducing fatigue.

Comfort is prioritized in the design of the Snapper 24 HP. It features an ergonomic seat and easy-to-reach controls, ensuring that users can mow their lawns for extended periods without discomfort. The removable engine cover allows for quick access to the engine for maintenance and repairs, enabling users to keep their equipment running in top condition.

Furthermore, the Snapper 24 HP is equipped with a warranty that underscores its durability and reliability. With its combination of power, versatility, and user-friendly features, the Snapper 24 HP stands out as an ideal choice for anyone looking to maintain an impeccably manicured lawn. Whether you are a seasoned lawn care professional or a homeowner who takes pride in their outdoor space, the Snapper 24 HP delivers performance and innovation you can trust.
Top Page Image Contents