Snapper 24 HP manual Sharpening the Mower Blade, Balancing the Mower Blades, Nail

Page 27

Sharpening the Mower Blade

CAUTION

Avoid injury! Mower blades are sharp.

•Always wear gloves when handling the mower blades.

•Always wear safety eye protection when grinding.

1.Sharpen the mower blades with grinder, hand file, or electric blade sharpener.

2.Sharpen the mower blade by removing an equal amount of material from each end of the mower blade.

3.Keep the original bevel (A, Figure 20) when grinding. DO NOT change the mower blade bevel.

4.The mower blade should have a maximum 1/64” (0,40 mm) cutting edge (B) or less.

5.Balance the mower blades before installing.

Balancing the Mower Blades

CAUTION

Avoid injury! Keep mower blades balanced.

•An unbalanced mower blade can create excessive vibration and damage the unit or cause mower blade failure.

1.Clean the mower blade to remove any dried grass or other debris.

2.See Figure 21. Put the mower blade on a nail in a vise and turn the mower blade to the horizontal position.

3.Check the balance of the mower blade. If either end of the mower blade moves downward, sharpen the heavy end until the mower blade is balanced. See Sharpening the Mower Blades for proper sharpening instructions.

4.Repeat the process until the mower blade remains in the horizontal position.

Reinstalling the Mower Blades

WARNING

For your personal safety, blade mounting capscrews must each be installed with a hex/spline washer and spring washer, then securely tightened. Torque blade mounting capscrew to 45-55 ft. lbs. (61-75 N.m.)

1.Reinstall each mower blade with the air lifts pointing up towards the mower deck as shown in Figure 22. Wedge a wooden block between the mower blade and the mower deck housing, and secure the mower blade with the mower blade mounting bolt, hex washer and spring washer (A, B & E, Figure 22) and torque to 45-55 ft. lbs. (61- 75 N.m).

Regular Maintenance

A

B

Figure 20. Sharpening the Mower Blade

A.Mower Blade Bevel

B.Mower Blade Cutting Edge

 

A

Figure 21. Balancing the Mower Blade

Maintenance

 

A. Nail

 

E

 

 

B

 

A

D

 

Figure 22. Tightening the Mower Blade for Installation

A. Mower Blade Mounting Bolt B. Hex Washer

C. Mower Blade Air Lift (Install With Points Up) D. 4 X 4 Wooden Block

E. Spring Washer

25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 24HP Zero-Turn Riders OPERATOR’S ManualDate Purchased Table of Contents Safety Rules & Information Operating SafetySlope Operation Retaining Walls, Drop-offs, and Water General Operation Slope Operation Safety Rules and InformationSafe Handling of Gasoline Service & MaintenanceIdentification Numbers CE Export Models Safety DecalsSafety Decals North American ModelsOperational Safety Checks Safety Interlock SystemNorth American Models only Safety Interlock System Export Models only Safety Interlock SystemServicing Safety IconsNorth American Safety Icons CE Export Safety IconsControl Functions Features & ControlsTransmission Oil Fill PTO SwitchSeat Adjustment Lever Hour MeterGeneral Operating Safety OperationChecks Before Starting Starting the Engine Stopping the Rider and EnginePushing the Rider by Hand Reverse Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Travel PracticeTurning Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Executing TurnsMower Removal Installation InstallationRemoval Tall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassProper Broadcast Mowing When and How Often to MowMowing Methods Mowing PatternsProper Mulching Attaching a TrailerRegular Maintenance Before Every Spring Each Hours 100 200 Fall UseCheck Transmission Oil Change Transmission Oil Filter Arm Pivot LubricationGrease OilServicing the Mower Blades Removing the Mower BladeInspecting the Mower Blades Nail Reinstalling the Mower BladesSharpening the Mower Blade Balancing the Mower BladesTire Pressure Check Tire PressuresAdding Fuel Fuel FilterChange Engine OIL & Filter Engine MaintenanceCheck / Fill Transmission OIL Transmission OIL Filter ChangeChange Interval Every 200 Hours Battery Maintenance Cleaning the Battery and CablesStorage Troubleshooting the Rider Troubleshooting, Adjustments, & ServiceTroubleshooting the Mower Troubleshooting, Adjustments, & ServiceStreaking Troubleshooting Common Cutting ProblemsSeat Adjustment Ground Speed Control Lever AdjustmentSeat Position Adjustment Speed Balancing Adjustment Cutting Height AdjustmentNeutral Adjustment Suspension Adjustment A. Front Shock Adjustment Collar Parking Brake AdjustmentBlade Brake Check PTO Clutch AdjustmentOrient Blades Side-to-Side Mower Deck LevelingRoller BAR Leveling Select Models Mower Belt ReplacementBattery Charging Hydraulic Pump Drive Belt ReplacementTechnical Manuals SpecificationsPage Belts and Blades Tractor Product Quick Specs

24 HP specifications

The Snapper 24 HP is a powerful and reliable riding lawn mower designed to tackle large lawns and challenging terrains with ease. With its robust engine and advanced features, it offers a premium mowing experience for homeowners and professionals alike.

At the heart of the Snapper 24 HP is a dependable 24 horsepower (HP) Briggs & Stratton engine. This high-performance engine provides ample power to efficiently cut through thick grass and maintain exhilarating speed while mowing. The engine is equipped with an overhead valve design, promoting better fuel efficiency and lower emissions, making it an environmentally friendly option.

One of the standout features of the Snapper 24 HP is its 42-inch cutting deck, which provides a wide cutting path for improved mowing efficiency. The deck is made from durable steel, designed to withstand the rigors of regular use, while also ensuring a clean and precise cut. It offers multiple cutting height adjustments, allowing users to customize their lawn's height from 1.5 to 4 inches, catering to various grass types and seasonal needs.

Additionally, the Snapper 24 HP comes with a hydrostatic transmission system that allows for smooth forward and reverse operation. This technology not only enhances maneuverability but also makes it easier to navigate obstacles such as trees and garden beds without the need for constant gear shifting. As a result, users can enjoy a more efficient mowing experience while reducing fatigue.

Comfort is prioritized in the design of the Snapper 24 HP. It features an ergonomic seat and easy-to-reach controls, ensuring that users can mow their lawns for extended periods without discomfort. The removable engine cover allows for quick access to the engine for maintenance and repairs, enabling users to keep their equipment running in top condition.

Furthermore, the Snapper 24 HP is equipped with a warranty that underscores its durability and reliability. With its combination of power, versatility, and user-friendly features, the Snapper 24 HP stands out as an ideal choice for anyone looking to maintain an impeccably manicured lawn. Whether you are a seasoned lawn care professional or a homeowner who takes pride in their outdoor space, the Snapper 24 HP delivers performance and innovation you can trust.
Top Page Image Contents