Snapper 24 HP manual Operation, General Operating Safety, Checks Before Starting

Page 16

Operation

Operation

GENERAL OPERATING SAFETY

Before first time operation:

•Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower.

•Become familiar with all of the controls and how to stop the unit.

•Drive in an open area without mowing to become accustomed to the unit brake lever or set the parking brake.

WARNING

Never operate on slopes greater than 17.6 percent (10°) which is a rise of 3-1/2 feet (106 cm) vertically in 20 feet (607 cm) horizontally. Select slow ground speed before driving onto a slope. Use extra caution when operating on slopes with a rear-mounted grass catcher. Mow across the face of slopes, not up and down, use caution when changing directions and DO NOT START OR STOP ON SLOPE.

WARNING

Never allow passengers to ride on the unit.

Before leaving the operator’s position for any reason, engage the parking brake, disengage the PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, tractor and mower free of grass, leaves and excess grease. Do not stop or park tractor over dry leaves, grass or combustible materials.

Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills.

CHECKS BEFORE STARTING

•Check that crankcase is filled to full mark on dipstick. See the engine Operator’s Manual for instructions and oil recommendations.

•Make sure all nuts, bolts, screws and pins are in place and tight.

•Adjust the seat position, and make certain you can reach all controls from operator’s position.

•Fill the fuel tank with fresh fuel. Refer to engine manual for fuel recommendations.

A

C

B

Figure 1. Pre-Start Checks

A.Fuel Tank Cap

B.Crankcase Oil Fill

C.Seat Adjustment Lever

WARNING

Do not load this zero-turn rider on a trailer or truck using two separate ramps. Only use a single ramp that is at least one foot wider than the width of the rear wheels of this rider. This rider has a zero turning radius and the rear wheels could fall off the ramps, or the rider could tip over injuring the operator or bystanders.

14

www.simplicitymfg.com www.snapper.com

Page 15 Page 17
Image 16
Page 15 Page 17
Contents OPERATOR’S Manual 24HP Zero-Turn RidersDate Purchased Table of Contents Operating Safety Safety Rules & InformationSlope Operation Retaining Walls, Drop-offs, and Water General Operation Safety Rules and Information Slope OperationService & Maintenance Safe Handling of GasolineIdentification Numbers Safety Decals Safety DecalsNorth American Models CE Export ModelsSafety Interlock System North American Models only Safety Interlock SystemExport Models only Safety Interlock System Operational Safety ChecksSafety Icons North American Safety IconsCE Export Safety Icons ServicingFeatures & Controls Control FunctionsPTO Switch Seat Adjustment LeverHour Meter Transmission Oil FillOperation General Operating SafetyChecks Before Starting Stopping the Rider and Engine Starting the EnginePushing the Rider by Hand Zero Turn Driving Practice Smooth TravelForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Executing an End-Of-Row Zero TurnExecuting Turns TurningInstallation Mower Removal InstallationRemoval Mowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingWhen and How Often to Mow Mowing MethodsMowing Patterns Proper Broadcast MowingAttaching a Trailer Proper MulchingBefore Every Spring Each Hours 100 200 Fall Use Regular MaintenanceCheck Transmission Oil Change Transmission Oil Filter Lubrication GreaseOil Arm PivotRemoving the Mower Blade Servicing the Mower BladesInspecting the Mower Blades Reinstalling the Mower Blades Sharpening the Mower BladeBalancing the Mower Blades NailCheck Tire Pressures Adding FuelFuel Filter Tire PressureEngine Maintenance Change Engine OIL & FilterTransmission OIL Filter Change Check / Fill Transmission OILChange Interval Every 200 Hours Cleaning the Battery and Cables Battery MaintenanceStorage Troubleshooting, Adjustments, & Service Troubleshooting the RiderTroubleshooting, Adjustments, & Service Troubleshooting the MowerTroubleshooting Common Cutting Problems StreakingGround Speed Control Lever Adjustment Seat AdjustmentSeat Position Adjustment Cutting Height Adjustment Speed Balancing AdjustmentNeutral Adjustment Parking Brake Adjustment Suspension Adjustment A. Front Shock Adjustment CollarPTO Clutch Adjustment Blade Brake CheckMower Deck Leveling Orient Blades Side-to-SideMower Belt Replacement Roller BAR Leveling Select ModelsHydraulic Pump Drive Belt Replacement Battery ChargingSpecifications Technical ManualsPage Product Quick Specs Belts and Blades Tractor

24 HP specifications

The Snapper 24 HP is a powerful and reliable riding lawn mower designed to tackle large lawns and challenging terrains with ease. With its robust engine and advanced features, it offers a premium mowing experience for homeowners and professionals alike.

At the heart of the Snapper 24 HP is a dependable 24 horsepower (HP) Briggs & Stratton engine. This high-performance engine provides ample power to efficiently cut through thick grass and maintain exhilarating speed while mowing. The engine is equipped with an overhead valve design, promoting better fuel efficiency and lower emissions, making it an environmentally friendly option.

One of the standout features of the Snapper 24 HP is its 42-inch cutting deck, which provides a wide cutting path for improved mowing efficiency. The deck is made from durable steel, designed to withstand the rigors of regular use, while also ensuring a clean and precise cut. It offers multiple cutting height adjustments, allowing users to customize their lawn's height from 1.5 to 4 inches, catering to various grass types and seasonal needs.

Additionally, the Snapper 24 HP comes with a hydrostatic transmission system that allows for smooth forward and reverse operation. This technology not only enhances maneuverability but also makes it easier to navigate obstacles such as trees and garden beds without the need for constant gear shifting. As a result, users can enjoy a more efficient mowing experience while reducing fatigue.

Comfort is prioritized in the design of the Snapper 24 HP. It features an ergonomic seat and easy-to-reach controls, ensuring that users can mow their lawns for extended periods without discomfort. The removable engine cover allows for quick access to the engine for maintenance and repairs, enabling users to keep their equipment running in top condition.

Furthermore, the Snapper 24 HP is equipped with a warranty that underscores its durability and reliability. With its combination of power, versatility, and user-friendly features, the Snapper 24 HP stands out as an ideal choice for anyone looking to maintain an impeccably manicured lawn. Whether you are a seasoned lawn care professional or a homeowner who takes pride in their outdoor space, the Snapper 24 HP delivers performance and innovation you can trust.
Top Page Image Contents