Snapper 24 HP manual Check / Fill Transmission OIL, Transmission OIL Filter Change

Page 30

Regular Maintenance

CHECK / FILL TRANSMISSION OIL

Oil Type: 20W-50 conventional detergent motor oil.

1.Check the oil level when the unit is cold. Raise the seat plate to gain access to the transmission oil reservoirs (A, Figure 26). The oil should be up to the “FULL COLD” mark (B). If the oil is below this level, proceed to step 2.

2.Before removing the reservoir cap, make sure the area around the reservoir cap and fill neck of the reservoir is free of dust, dirt, or other debris.

Remove the reservoir cap.

3.Add oil up to the “FULL COLD” mark (B, Figure 26).

4.Reinstall the reservoir cap.

A

B

Figure 26. Transmission Oil Reservoirs

A.Transmission Oil Reservoirs

B.“FULL COLD” Mark

Maintenance

TRANSMISSION OIL FILTER CHANGE

Change Interval: Every 200 Hours

1.Locate the transmission oil filters (A, Figure 27) underneath the rear of the machine on the transmissions.

2.Remove the three 1/4” filter guard screws (C) and the filter guard (B).

3.Clean the area around the filter base and remove the filter.

4.Apply a film of new oil to the gasket of the new replacement filter. After the oil has drained, thread the new filter onto the filter base until the gasket makes contact, then tighten 3/4 of a turn more.

5.Reinstall the filter guard with the three 1/4” filter guard screws

6.Using a hex bit swivel socket or a modified allen wrench remove the top port plug from the transmissions.

7.Remove the transmission reservoir cap and fill with oil until oil appears at the bottom of the transmission’s top port (approximately 2 qts (1,89L).

8.Reinstall the top port plug and tighten to 15 ft lbs (20,38 Nm).

9.Continue to add oil to the transmission oil reservoirs until the oil lever reaches the “FULL COLD” mark. Reinstall the oil reservoir cap.

10.Repeat this process for the other side of the machine.

A

B

D

C

Figure 27. Transmission (Left Side Shown.)

A.Transmission Oil Filter

B.Filter Guard

C.1/4” Filter Guard Screws

D.Top Port Plug

11.Run the unit for several minutes and check the transmission oil level.

IMPORTANT NOTE: Use caution after changing the filter; air in the hydraulic system may affect the responsiveness of the control levers. Repeat step 11 until the air is out of the system.

28

www.simplicitymfg.com www.snapper.com

Page 29 Page 31
Image 30
Page 29 Page 31
Contents OPERATOR’S Manual 24HP Zero-Turn RidersDate Purchased Table of Contents Operating Safety Safety Rules & InformationSlope Operation Retaining Walls, Drop-offs, and Water General Operation Safety Rules and Information Slope OperationService & Maintenance Safe Handling of GasolineIdentification Numbers North American Models Safety DecalsSafety Decals CE Export ModelsExport Models only Safety Interlock System Safety Interlock SystemNorth American Models only Safety Interlock System Operational Safety ChecksCE Export Safety Icons Safety IconsNorth American Safety Icons ServicingFeatures & Controls Control FunctionsHour Meter PTO SwitchSeat Adjustment Lever Transmission Oil FillGeneral Operating Safety OperationChecks Before Starting Starting the Engine Stopping the Rider and EnginePushing the Rider by Hand Forward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting Turns Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn TurningMower Removal Installation InstallationRemoval Height of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingAttaching a Trailer Proper MulchingRegular Maintenance Before Every Spring Each Hours 100 200 Fall UseCheck Transmission Oil Change Transmission Oil Filter Oil LubricationGrease Arm PivotServicing the Mower Blades Removing the Mower BladeInspecting the Mower Blades Balancing the Mower Blades Reinstalling the Mower BladesSharpening the Mower Blade NailFuel Filter Check Tire PressuresAdding Fuel Tire PressureEngine Maintenance Change Engine OIL & FilterCheck / Fill Transmission OIL Transmission OIL Filter ChangeChange Interval Every 200 Hours Battery Maintenance Cleaning the Battery and CablesStorage Troubleshooting, Adjustments, & Service Troubleshooting the RiderTroubleshooting, Adjustments, & Service Troubleshooting the MowerTroubleshooting Common Cutting Problems StreakingSeat Adjustment Ground Speed Control Lever AdjustmentSeat Position Adjustment Speed Balancing Adjustment Cutting Height AdjustmentNeutral Adjustment Parking Brake Adjustment Suspension Adjustment A. Front Shock Adjustment CollarPTO Clutch Adjustment Blade Brake CheckMower Deck Leveling Orient Blades Side-to-SideMower Belt Replacement Roller BAR Leveling Select ModelsHydraulic Pump Drive Belt Replacement Battery ChargingSpecifications Technical ManualsPage Product Quick Specs Belts and Blades Tractor

24 HP specifications

The Snapper 24 HP is a powerful and reliable riding lawn mower designed to tackle large lawns and challenging terrains with ease. With its robust engine and advanced features, it offers a premium mowing experience for homeowners and professionals alike.

At the heart of the Snapper 24 HP is a dependable 24 horsepower (HP) Briggs & Stratton engine. This high-performance engine provides ample power to efficiently cut through thick grass and maintain exhilarating speed while mowing. The engine is equipped with an overhead valve design, promoting better fuel efficiency and lower emissions, making it an environmentally friendly option.

One of the standout features of the Snapper 24 HP is its 42-inch cutting deck, which provides a wide cutting path for improved mowing efficiency. The deck is made from durable steel, designed to withstand the rigors of regular use, while also ensuring a clean and precise cut. It offers multiple cutting height adjustments, allowing users to customize their lawn's height from 1.5 to 4 inches, catering to various grass types and seasonal needs.

Additionally, the Snapper 24 HP comes with a hydrostatic transmission system that allows for smooth forward and reverse operation. This technology not only enhances maneuverability but also makes it easier to navigate obstacles such as trees and garden beds without the need for constant gear shifting. As a result, users can enjoy a more efficient mowing experience while reducing fatigue.

Comfort is prioritized in the design of the Snapper 24 HP. It features an ergonomic seat and easy-to-reach controls, ensuring that users can mow their lawns for extended periods without discomfort. The removable engine cover allows for quick access to the engine for maintenance and repairs, enabling users to keep their equipment running in top condition.

Furthermore, the Snapper 24 HP is equipped with a warranty that underscores its durability and reliability. With its combination of power, versatility, and user-friendly features, the Snapper 24 HP stands out as an ideal choice for anyone looking to maintain an impeccably manicured lawn. Whether you are a seasoned lawn care professional or a homeowner who takes pride in their outdoor space, the Snapper 24 HP delivers performance and innovation you can trust.
Top Page Image Contents