Snapper 2167519B specifications Maintenance, Service Periodic, Storage Procedure

Page 13

Maintenance (Continued)

!

WARNING

!

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

Check Mower Blade

1.Disconnect the spark plug wire and secure the end away from the plug.

2.Tilt the mower up on its rear wheels for access to the blade cap screw (A, Figure 19). Do not tilt the mower with the spark plug or carburetor down.

Important: Drain the fuel tank before tipping the mower. DO NOT tip the machine with the carburetor or spark plug down. Oil from the crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

3.Check the torque of the blade cap screw. Recommended torque should be 40 ft. lbs.

4.Check the blade for sharpness, wear and damage. Refer to the Section entitled “Blade Wear Limits”.

A

Figure 19: Tightening the blade cap screw

Check Transmission Poly-V Belt

1.Visually check the poly-v belt for cracking, fraying, sev- ered or exposed belt strands. If worn or damaged, replace the belt before operating the mower.

Service - Periodic

Perform all maintenance as described in the “Service Schedule” section of this manual.

Engine

Service the engine according to the engine owner’s manual.

Air Filter

Refer to the engine owner’s manual for service instructions.

Engine Oil

Refer to the engine owner’s manual for service instructions.

Storage Procedure

Refer to the Engine Owner’s Manual for directions regarding engine storage preparations. Prepare the mower for “end of season” storage as follows:

1.Drain the fuel from the fuel tank and let the engine run until all fuel is out of the carburetor.

2.Disconnect and remove the spark plug wire away from the spark plug before any other preparations are made!

3.Tape all openings closed to prevent spraying water into the exhaust or air intakes during washing.

4.Tilt the mower up on its rear wheels and thoroughly clean the underside of the deck. Do not tilt the mower with the spark plug or carburetor down. Scrape away any accumulation of grass with a putty knife and/or wire brush.

5.Lubricate all exposed metal with a light coating of oil to prevent corrosion.

6.On self-propelled models, disconnect the transfer rod clip and remove the ground speed control rod before folding the handles.

7.Loosen the handle knobs. Carefully fold the handles forward, “flexing” the control cables to prevent cable damage.

8.Store the mower in a shed or other dry area, protected from weather.

Maintenance

Check Engine Drive Belt

1.Visually check the engine drive belt for cracking, fraying, severed or exposed belt strands. If worn or damaged, replace the belt before operating the mower.

11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Steel Deck Walk Mowers Series Engine Date of Purchase Retailer Retailers Phone Number EquipmentTable of Contents Slope Operation Protection for ChildrenPreparation From Previous Column PreparationSafe Handling of Gasoline From Previous Maintenance and StorageOperation Operation From Previous ColumnFeatures and Controls Features and ControlsStarting and Operation Operation Pre-Start Check ListEngine and Blade Briggs Engines Operation Handle Height AdjustmentStopping Engine and Blade Kawasaki EngineRecycling Operation Cutting Height AdjustmentRemoving the Recycling Cover Installing the Grass Bag Adapter Installing the Discharge DeflectorInstalling the Grass Bag Installing the Recycling PlugService After First 5 Hours Maintenance Maintenance IntroductionCheck Grease Level in Transmission Change Engine OilService Periodic MaintenanceStorage Procedure Standard Blade Wear Limit Mower Blade ReplacementNinja Blade Wear Limit Blade SharpeningWheel Drive Control Adjustment Self-Propelled Models Only Cleaning Drive Disc & Driven Disc Driven and Drive Disc ServiceDrive Spring Repair/Replacement Driven Disc AdjustmentAdjusting the driven disc Driven Disc ReplacementRemoving the driven disc assembly Driven Disc Bearing ReplacementEngine Drive Belt Replacement Stretch Type Belts Belt ServiceReplacing the Bearing On the Pulley End Of the Hex Shaft Procedure Transmission Poly-V Belt ReplacementNew Battery Preparation Maintenance Battery ServiceBattery Service Battery StorageMaintenance/Replacement Parts Service ScheduleProbable Cause Corrective Action TroubleshootingYear Limited Warranty Page Page Page Common Service Parts Product Specifications

2167519B specifications

Snapper 2167519B represents a sophisticated approach to outdoor power equipment, designed to meet the needs of both casual users and professional landscapers. This high-performance walk-behind mower is engineered for efficiency, durability, and convenience, making it a popular choice among lawn care enthusiasts.

One of the standout features of the Snapper 2167519B is its robust 190cc engine. This powerful engine provides ample torque and performance, enabling the mower to easily tackle a variety of grass types and terrains. The engine is designed for easy starting and reliable operation, ensuring that users can get to work without the frustrations often associated with small engines.

The Snapper 2167519B is equipped with a 21-inch cutting deck, which strikes a balance between maneuverability and cutting capacity. This size is ideal for residential lawns and smaller commercial properties, making it versatile for different mowing needs. The deck is constructed from high-quality materials to withstand the rigors of frequent use, and it features a design that promotes efficient grass clipping discharge, whether mulching, bagging, or side discharging.

Another key characteristic of the Snapper 2167519B is its height adjustment feature, which allows users to easily modify cutting heights between 1 to 4 inches. This feature accommodates various grass types and user preferences, ensuring a clean and even cut every time.

User comfort is also a priority for the Snapper 2167519B. The mower features ergonomic handlebars designed to reduce fatigue during extended operation. Additionally, the self-propelled option enhances ease of use, allowing users to navigate hilly terrains or dense grass with minimal effort.

In terms of technology, the Snapper 2167519B includes a rear-wheel drive system, which provides excellent traction and stability on uneven surfaces. The design also features larger rear wheels that enhance maneuverability and ease of turning.

In summary, the Snapper 2167519B is a compelling choice for anyone in need of a dependable and efficient walk-behind mower. With its powerful engine, versatile cutting capabilities, and user-friendly features, this mower is well-suited for a variety of lawn care tasks, delivering quality performance season after season. Whether for residential use or light commercial applications, the Snapper 2167519B stands out as a reliable and effective tool for maintaining any lawn.
Top Page Image Contents