Snapper 2167519B specifications Transmission Poly-V Belt Replacement, Procedure

Page 20

Maintenance (Continued)

Maintenance

!

WARNING

!

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

Engine Drive Belt Replacement (Stretch Type Belts - Continued)

IMPORTANT: Drain the fuel tank before tipping the mower. DO NOT tip the machine with the carburetor or spark plug down. Oil from the crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

3.

Remove the driven disc. Refer to the Section entitled

 

“Driven Disc Replacement” for driven disc removal

 

procedure.

4.

Drain the fuel tank before tipping the mower. Do not tilt

 

the mower with the spark plug or carburetor down. Tilt

 

the mower up on its rear wheels and remove the blade

 

and blade hub. Assistance from another person may be

 

necessary to hold the mower in the tilted position.

5.

Hold the slotted end of the drive disc bolt (B, Figure 35)

 

with a screwdriver and remove the nut (G) and internal

 

tooth lock washer (F).

6.

Remove the belt cover, located under the deck.

7.

Lift the drive disc (A) up and remove the worn belt.

8.

Loop one end of the new belt over the engine pulley and

 

insert the other end through the slot in the deck.

9.

Loop the belt around the pulley on the bottom of the

 

drive disc.

A

B

C

D

E

F

G

Figure 35: Removing the drive disc

Transmission Poly-V Belt Replacement

1.Remove the driven disc. Refer to the Section entitled “Replacing Driven Disc Rubber Ring”.

2.Note the routing of the old belt around the three pulleys before removing it.

3.Place the new Poly-V Belt (A, Figure 36) over the end of the hex shaft (B) and onto the drive pulley (C).

4.Work the belt onto the top of the idler pulley (D).

5.Twist the belt sideways and pull it upward between the differential bracket (E) and driven pulley (F) and then down into the pulley groove. Make sure the Poly-V Belt is above the belt guide (G).

10. Reinstall the drive disc and retaining hardware.

IMPORTANT: 1) The square shoulder of the drive disc bolt must fit into the square hole of the bushing. 2) The square end of bushing must fit into the bracket slot.

11.Reinstall the belt cover and tighten the bolts securely.

12.Reinstall the blade hub and cutter blade. Recommended torque for the blade cap screw is 40 ft. lbs.

C

B

D

G

E

A

F

Figure 36: Poly-v belt routing

18

www.snapper.com

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Steel Deck Walk Mowers Series Date of Purchase Retailer Retailers Phone Number Equipment EngineTable of Contents Protection for Children Slope OperationPreparation From Previous Column PreparationMaintenance and Storage Safe Handling of Gasoline From PreviousOperation Operation From Previous ColumnFeatures and Controls Features and ControlsEngine and Blade Briggs Engines Operation Pre-Start Check ListStarting and Operation Handle Height Adjustment OperationStopping Engine and Blade Kawasaki EngineRemoving the Recycling Cover Cutting Height AdjustmentRecycling Operation Installing the Discharge Deflector Installing the Grass Bag AdapterInstalling the Recycling Plug Installing the Grass BagMaintenance Maintenance Introduction Service After First 5 HoursCheck Grease Level in Transmission Change Engine OilStorage Procedure MaintenanceService Periodic Mower Blade Replacement Standard Blade Wear LimitNinja Blade Wear Limit Blade SharpeningWheel Drive Control Adjustment Self-Propelled Models Only Driven and Drive Disc Service Cleaning Drive Disc & Driven DiscDrive Spring Repair/Replacement Driven Disc AdjustmentDriven Disc Replacement Adjusting the driven discDriven Disc Bearing Replacement Removing the driven disc assemblyReplacing the Bearing On the Pulley End Of the Hex Shaft Belt ServiceEngine Drive Belt Replacement Stretch Type Belts Transmission Poly-V Belt Replacement ProcedureMaintenance Battery Service New Battery PreparationBattery Service Battery StorageService Schedule Maintenance/Replacement PartsTroubleshooting Probable Cause Corrective ActionYear Limited Warranty Page Page Page Product Specifications Common Service Parts

2167519B specifications

Snapper 2167519B represents a sophisticated approach to outdoor power equipment, designed to meet the needs of both casual users and professional landscapers. This high-performance walk-behind mower is engineered for efficiency, durability, and convenience, making it a popular choice among lawn care enthusiasts.

One of the standout features of the Snapper 2167519B is its robust 190cc engine. This powerful engine provides ample torque and performance, enabling the mower to easily tackle a variety of grass types and terrains. The engine is designed for easy starting and reliable operation, ensuring that users can get to work without the frustrations often associated with small engines.

The Snapper 2167519B is equipped with a 21-inch cutting deck, which strikes a balance between maneuverability and cutting capacity. This size is ideal for residential lawns and smaller commercial properties, making it versatile for different mowing needs. The deck is constructed from high-quality materials to withstand the rigors of frequent use, and it features a design that promotes efficient grass clipping discharge, whether mulching, bagging, or side discharging.

Another key characteristic of the Snapper 2167519B is its height adjustment feature, which allows users to easily modify cutting heights between 1 to 4 inches. This feature accommodates various grass types and user preferences, ensuring a clean and even cut every time.

User comfort is also a priority for the Snapper 2167519B. The mower features ergonomic handlebars designed to reduce fatigue during extended operation. Additionally, the self-propelled option enhances ease of use, allowing users to navigate hilly terrains or dense grass with minimal effort.

In terms of technology, the Snapper 2167519B includes a rear-wheel drive system, which provides excellent traction and stability on uneven surfaces. The design also features larger rear wheels that enhance maneuverability and ease of turning.

In summary, the Snapper 2167519B is a compelling choice for anyone in need of a dependable and efficient walk-behind mower. With its powerful engine, versatile cutting capabilities, and user-friendly features, this mower is well-suited for a variety of lawn care tasks, delivering quality performance season after season. Whether for residential use or light commercial applications, the Snapper 2167519B stands out as a reliable and effective tool for maintaining any lawn.
Top Page Image Contents