Snapper CP215520HV specifications Driven Disc Ring Replacement, Proper driven disc adjustment

Page 18

Maintenance (Continued)

!

WARNING

!

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

Driven Disc Adjustment (Continued)

2.Remove the driven disc spring (A, Figure 28) from the driven disc assembly (B). Also remove the pin and washer (C) from the transfer rod (D), and remove the end of the transfer rod from the hole in the driven disc assembly.

A

B

Maintenance

A

B

D C

Figure 29: Proper driven disc adjustment

C

A

D

B E

Figure 28: Adjusting the driven disc

3.Slide the driven disc assembly over to 1/8” (A, Figure 29) from the outside edge of the drive disc (B).

4.Loosen the jam nut (A, Figure 30) securing the transfer rod (B) to the ball joint (C) on the pivot bracket (D).

5.Turn the rod in or out of the ball joint until the end of the rod aligns with the hole (E) in the driven disc assembly from which the rod was removed.

IMPORTANT: Do not move the pivot bracket.

6.Reinstall the rod as removed in Step 2. Move the ground speed control to the ‘slow’ position, then back to the ‘fast’ position. Recheck the 1/8” measurement described previously. Readjust as needed. Tighten the nut when finished.

7.Reinstall the driven disc spring to the driven disc assembly.

Figure 30: Adjusting the transfer rod

Driven Disc Ring Replacement

If the rubber ring on the driven disc is badly chunked or worn, it must be replaced. Install a new driven disc ring as follows:

1.Remove the pin and washer (C, Figure 28) from the transfer rod (D), and remove the end of the transfer rod from the hole in the driven disc assembly.

16

www.snapper.com

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Steel Deck Walk Mowers Commercial Models Series Date of Purchase Retailer Retailers Phone Number Equipment EngineTable of Contents Preparation Protection for ChildrenSlope Operation Preparation From Previous ColumnOperation Maintenance and StorageSafe Handling of Gasoline From Previous Operation From Previous ColumnFeatures and Controls Features and ControlsOperation Pre-Start Check List Starting and OperationEngine and Blade Handle Height Adjustment OperationPropelling the Mower Cutting Height Adjustment Recycling OperationRemoving the Recycling Cover Installing the Discharge Deflector Installing the Grass Bag AdapterInstalling the Recycling Plug Installing the recycling plugInstalling the Grass Bag Dumping the Grass BagCheck Grease Level in Transmission Maintenance Maintenance IntroductionService After First 5 Hours Change Engine OilMaintenance Service PeriodicStorage Procedure Ninja Blade Wear Limit Mower Blade ReplacementStandard Blade Wear Limit Blade SharpeningWheel Drive Control Adjustment Self-Propelled Models Only Drive Spring Repair/Replacement Driven and Drive Disc ServiceCleaning Drive Disc & Driven Disc Driven Disc AdjustmentDriven Disc Ring Replacement Proper driven disc adjustmentDriven Disc Bearing Replacement Replacing the driven disc bearingBelt Service Engine Drive Belt Replacement Stretch Type BeltsReplacing the Bearing On the Pulley End Of the Hex Shaft Transmission Poly-V Belt Replacement ProcedureService Schedule Maintenance/Replacement PartsTroubleshooting Probable Cause Corrective ActionYear Limited Warranty Page Page Page Product Specifications Common Service Parts Part Number

CP215520HV specifications

The Snapper CP215520HV is an exceptional residential riding mower that combines power, performance, and versatility, catering to homeowners looking for an efficient way to maintain their lawns. This model features a robust 21.5-horsepower Briggs & Stratton engine, known for its reliability and ease of starting. The engine delivers ample power to handle various mowing conditions, making quick work of grassy terrains.

One of the standout features of the Snapper CP215520HV is its cutting deck. The 42-inch, fabricated steel deck provides a wide cutting path, which helps to reduce mowing time while ensuring a clean cut. The deck is designed with a washout port, making it easy for users to clean the underside and maintain optimal performance. This model also offers multiple cutting height adjustments, ranging from 1.5 to 4.5 inches. This versatility allows homeowners to tailor the mowing height to suit their lawn's needs and seasonal changes.

In terms of comfort and control, the Snapper CP215520HV is equipped with an ergonomic steering wheel and a comfortable high-back seat. The operator station is designed for ease of use, allowing for intuitive handling without fatigue during extended mowing sessions. The steering system features a tight turning radius, enabling easy maneuverability around gardens and landscaping features.

The mower is built with durability in mind, constructed from sturdy materials designed to withstand the rigors of regular use. The heavy-duty frame offers stability and longevity, ensuring that the mower remains a reliable partner for years. Additionally, the Snapper CP215520HV incorporates a hydrostatic transmission, providing smooth and responsive speed control without the need for shifting gears.

Safety features are also a priority with this model. The mower is equipped with an automatic engine shut-off function that activates when the operator leaves the seat, preventing potential accidents. Furthermore, the headlights improve visibility during early morning or late evening mowing tasks.

Overall, the Snapper CP215520HV is an impressive amalgamation of innovative technology, user-friendly features, and durable construction. Designed for both efficiency and comfort, it stands out as a top choice for homeowners seeking a dependable riding mower that can tackle residential lawns effectively. Whether users need to mow a small yard or a larger property, this model promises to deliver exceptional results.
Top Page Image Contents