Snapper E331522KVE, E281022BE, E281222BE Starting & Operation, Engine Electric Start

Page 10

Section 2 - OPERATING INSTRUCTIONS

2.3STARTING & OPERATION

2.3.1. ENGINE (ELECTRIC START) (Continued)

8.Should the battery be too weak to start the engine, Refer to Section “ENGINE (MANUAL START)” to manually start the electric start engines.

2.3.2. ENGINE (MANUAL START)

IMPORTANT: When the ignition key is turned to “ON”, and the recoil handle is pulled, the engine will turn over, but will not start unless the Clutch/Brake Pedal is pressed all the way down with Parking Brake engaged (See Figure 2.8) and the Blade Lever is in the “Off” position (See Figure 2.4). Start engine as follows:

1.Move transmission shift lever to (N) Neutral position. DO NOT start engine with transmission shift lever in a drive position.

WARNING

It is possible to start engine with transmission shift lever in a drive position. Follow starting instructions carefully.

2.Make certain the Blade Lever is in the “Off” position. See Figure 2.4.

3.Press Clutch/Brake Pedal all the way down, move Parking Brake Latch over and release the Clutch/Brake Pedal to set Parking Brake. See Figure 2.8.

TO START ENGINE, PUSH

CLUTCH/BRAKE PEDAL ALL

THE WAY DOWN

5.Move engine speed control to the choke position to start a cold engine. See Figure 2.6

6.Turn key to “ON” position. See Figure 2.9.

KEY

FIGURE 2.9

7.Pull starter rope with a smooth, even motion until engine starts. Always guide the starter rope back into the recoil housing. Never allow rope to snap back. After Engine starts, move engine speed control to the “FAST” position.

8.Allow a brief warm-up until engine runs smooth.

MOVE

PARKING

BRAKE

LATCH

OVER

FIGURE 2.8

4.Open vent on fuel filler cap by turning counterclockwise. NOTE: Failure to open vent on the fuel filler cap can cause engine to stall. See Figure 2.2.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents European Rear Engine Riding Mower Series Manual No -4391 I.R /19/01Important Safety Instructions Operation Table of Contents Introduction NomenclatureFamiliarization Decals / Symbols Lowest Height CUT Battery Caution OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Electric Start Starting & OperationEngine Manual Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Cutting Height AdjustmentDo not park machine on slopes Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideService After First 5 Hours Change Engine OIL Service Engine AIR Cleaner Check Mower BladeService Brake / Park Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltBlade Brake Clean Mower Deck Service Every 25 Operating HoursBattery Fluid Level Interlock SystemFront Wheel Bearing Lubrication Service Every 25 Operating Hours from previousRear Axle Bearing Lubrication Fuel Filter Service AnnuallyEngine Every TWO YearsStorage OUT of Season Removing Fuel TankEngine Adjustments & Repair Mower Drive Belt Adjustment for 28 Decks onlyBlade Brake Adjustment Mower Deck Adjustment Side-To-Side LevelnessMower Deck Adjustment Front to Rear Levelness 28 & 33 DecksChain Case Clutch Yoke Cable Housing Spring Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBelt Removal Blade Drive Belt ReplacementBelt Replacement DecksBattery Battery Removal Battery InstallationNEW Battery Preparation 1. Remove battery from carton Battery ServiceBattery Storage Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopCutting Grass Loss Of TractionBlades Not Cutting ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyService Notes European Rear Engine Riding Mower Series

E281022BE, E281222BE, E331522KVE, E331522KVE, E281022BE, E281222BE, E281222BE, E281022BE, E331522KVE specifications

The Snapper E281222BE, E281022BE, and E331522KVE models are part of Snapper’s extensive range of outdoor power equipment, known for their reliability and innovative features. These models are designed to cater to the needs of homeowners and professional landscapers alike, providing efficient and effective solutions for lawn care.

Starting with the Snapper E281222BE, this model stands out with its 21-inch cutting deck, which facilitates a wider cutting path, reducing mowing time. It is equipped with a powerful Briggs & Stratton engine that delivers strong performance, allowing for efficient cutting through various types of grass and terrain. The E281222BE also features a 3-in-1 mowing system, enabling users to mulch, bag, or side discharge grass clippings, offering versatility depending on the user's preference and yard conditions.

Next in line, the Snapper E281022BE presents a similar design but with slight modifications geared towards providing an economical and efficient solution for smaller lawns. This model also has a 21-inch cutting deck and shares the robust engine characteristics of its counterpart. However, it’s particularly known for its lightweight construction, making it easier to maneuver around tight spaces and flower beds. The E281022BE promotes excellent grass management with its easy-to-use height adjustment system that allows for customized cutting heights.

The E331522KVE model, on the other hand, offers additional features aimed at enhancing user experience. It boasts a larger 33-inch cutting deck, making it ideal for medium to large lawns. This model is powered by a powerful engine designed for high performance, while its variable-speed drive system allows for greater control over mowing speed. Furthermore, the E331522KVE integrates advanced technologies such as Smart-Cut™ technology, which adjusts power and speed automatically according to grass conditions, ensuring efficient grass management in varying scenarios.

All models feature durable construction with weather-resistant components, making them reliable choices for all seasons. Ergonomically designed handles and easy-to-access controls ensure comfort during extended use. Snapper’s commitment to sustainability is reflected in these models, as they are designed to maintain optimal fuel efficiency while minimizing emissions.

In conclusion, Snapper's E281222BE, E281022BE, and E331522KVE models offer a blend of power, efficiency, and ease of use. These characteristics make them suitable for various lawn care tasks while catering to the specific needs of the user. Whether you’re maintaining a small residential lawn or managing larger grassy areas, these Snapper models provide the performance and features necessary to achieve a beautifully manicured landscape.
Top Page Image Contents