Snapper E331522KVE, E281022BE, E281222BE Blade Brake, Service Brake / Park Brake

Page 16

Section 3 - MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.4. CHECK BLADE DRIVE BELT

The blade drive consists of a single belt from the engine to the deck. Inspect for signs of deterioration and proper tension.

1.Lower deck to lowest setting.

2.Remove four self-tapping screws, two on each side of mower drive belt cover. See Figure 3.3.

3.Slide cover back and rotate out.

or slack it must be replaced. Refer to Section “BLADE DRIVE BELT REPLACEMENT”.

ENGINE

PULLEY

BELT SPACING SHOULD BE 1-1/4”

IDLER

PULLEY

REMOVE FOUR (4)

SELF-TAPPING

SCREWS

REMOVE COVER

FIGURE 3.3

4.With engine “OFF” and deck in 3rd height of cut position, move blade lever back to the “ON” position and depress blade pedals.

5.28” and 30” Decks: Measure the belt spacing at idler pulley. See Figure 3.4. The belt spacing should be 1 1/4” but no less 1”. If the measurement is less than 1”, the belt tension should be adjusted.

Refer to Section “BLADE DRIVE BELT ADJUSTMENT”.

WARNING

The following procedure requires the engine and blades to be operated. Exercise extreme caution. Clear area of loose parts & tools first. Only operate blades when seated in the operator’s seat.

IMPORTANT: The blade drive belt on 33” decks does not require tension adjustment. If the belt becomes worn

MOWER

DECK

PULLEY

FIGURE 3.4

3.2.5.BLADE BRAKE

1.Check blade brake for proper function. Blade should stop rotating in 3 seconds or less after moving the blade control lever to the “OFF” position or after releasing the blade pedals.

WARNING

Blades must stop rotating in 3 seconds or less after the blade has been turned off. DO NOT operate machine until blade brake has been adjusted and functioning properly.

2.If the blade continues to rotate longer than 3 seconds do not operate machine. Refer to Section “BLADE BRAKE ADJUSTMENT” or contact your SNAPPER dealer for assistance.

3.2.6.SERVICE BRAKE / PARK BRAKE

1.Check machine brake for proper function. Engage park brake. Push machine. Rear tires should skid. Drive machine forward and apply brake. Machine should come to a complete stop in less than 5 ft.

2.If brakes are not functioning properly brake adjustment must be completed before operating machine. Refer to Section “SERVICE BRAKE –

PARK BRAKE ADJUSTMENT”.

16

Image 16
Contents European Rear Engine Riding Mower Series Manual No -4391 I.R /19/01Important Safety Instructions Operation Table of Contents Introduction NomenclatureFamiliarization Decals / Symbols Lowest Height CUT Battery Caution OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Electric Start Starting & OperationEngine Manual Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Cutting Height AdjustmentDo not park machine on slopes Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideService After First 5 Hours Change Engine OIL Service Engine AIR Cleaner Check Mower BladeService Brake / Park Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltBlade Brake Service Every 25 Operating Hours Battery Fluid LevelClean Mower Deck Interlock SystemFront Wheel Bearing Lubrication Service Every 25 Operating Hours from previousRear Axle Bearing Lubrication Service Annually EngineFuel Filter Every TWO YearsStorage OUT of Season Removing Fuel TankEngine Adjustments & Repair Mower Drive Belt Adjustment for 28 Decks onlyBlade Brake Adjustment Mower Deck Adjustment Side-To-Side LevelnessMower Deck Adjustment Front to Rear Levelness 28 & 33 DecksChain Case Clutch Yoke Cable Housing Spring Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBlade Drive Belt Replacement Belt ReplacementBelt Removal DecksBattery Battery Removal Battery InstallationBattery Service Battery StorageNEW Battery Preparation 1. Remove battery from carton Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopLoss Of Traction Blades Not CuttingCutting Grass ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyService Notes European Rear Engine Riding Mower Series

E281022BE, E281222BE, E331522KVE, E331522KVE, E281022BE, E281222BE, E281222BE, E281022BE, E331522KVE specifications

The Snapper E281222BE, E281022BE, and E331522KVE models are part of Snapper’s extensive range of outdoor power equipment, known for their reliability and innovative features. These models are designed to cater to the needs of homeowners and professional landscapers alike, providing efficient and effective solutions for lawn care.

Starting with the Snapper E281222BE, this model stands out with its 21-inch cutting deck, which facilitates a wider cutting path, reducing mowing time. It is equipped with a powerful Briggs & Stratton engine that delivers strong performance, allowing for efficient cutting through various types of grass and terrain. The E281222BE also features a 3-in-1 mowing system, enabling users to mulch, bag, or side discharge grass clippings, offering versatility depending on the user's preference and yard conditions.

Next in line, the Snapper E281022BE presents a similar design but with slight modifications geared towards providing an economical and efficient solution for smaller lawns. This model also has a 21-inch cutting deck and shares the robust engine characteristics of its counterpart. However, it’s particularly known for its lightweight construction, making it easier to maneuver around tight spaces and flower beds. The E281022BE promotes excellent grass management with its easy-to-use height adjustment system that allows for customized cutting heights.

The E331522KVE model, on the other hand, offers additional features aimed at enhancing user experience. It boasts a larger 33-inch cutting deck, making it ideal for medium to large lawns. This model is powered by a powerful engine designed for high performance, while its variable-speed drive system allows for greater control over mowing speed. Furthermore, the E331522KVE integrates advanced technologies such as Smart-Cut™ technology, which adjusts power and speed automatically according to grass conditions, ensuring efficient grass management in varying scenarios.

All models feature durable construction with weather-resistant components, making them reliable choices for all seasons. Ergonomically designed handles and easy-to-access controls ensure comfort during extended use. Snapper’s commitment to sustainability is reflected in these models, as they are designed to maintain optimal fuel efficiency while minimizing emissions.

In conclusion, Snapper's E281222BE, E281022BE, and E331522KVE models offer a blend of power, efficiency, and ease of use. These characteristics make them suitable for various lawn care tasks while catering to the specific needs of the user. Whether you’re maintaining a small residential lawn or managing larger grassy areas, these Snapper models provide the performance and features necessary to achieve a beautifully manicured landscape.