Snapper E281022BE, E281222BE, E331522KVE Interlock System, Lubrication Grease Fittings

Page 17

Section 3 - MAINTENANCE

3.2.7. INTERLOCK SYSTEM

Check interlock controls for proper function:

The engine MUST NOT start if:

1.Blade Control is “ON” and/or clutch/brake pedal is released.

The engine and blades MUST STOP if:

2.The operator leaves the operator position with Blade Control “ON” and/or clutch/brake pedal is released.

WARNING

DO NOT operate machine if interlock system is not functioning properly. Contact your SNAPPER dealer immediately for assistance.

3.2.8. REVERSE LOCKOUT MECHANISM

Check function of Reverse Lockout Mechanism with engine off.

1.Depress and hold blade pedals.

2.Depress and hold clutch/brake pedal.

3.Shift lever must not go into reverse.

WARNING

DO NOT operate machine if Reverse Lockout Mechanism is not functioning properly. Contact your SNAPPER dealer immediately for assistance.

3.2.9. LUBRICATION – GREASE FITTINGS

The following components on the Rear Engine Rider are equipped with grease fittings and require periodic lubrication. Apply General Purpose grease (NLGI No.2) with a grease gun.

1.Front Wheel Bearings. Refer to Section “FRONT WHEEL BEARINGS – LUBRICATION”.

2.Rear Axle Bearing. Refer to Section “REAR AXLE BEARING – LUBRICATION”.

3.Mower Blade Spindle. Refer to Section “MOWER BLADE SPINDLE – LUBRICATION”.

3.3SERVICE - EVERY 25 OPERATING HOURS

3.3.1.Perform all service required after the first 5 hours of operation. Refer to Section “SERVICE – AFTER 5 HOURS”.

3.3.2.BATTERY FLUID LEVEL

1.Remove battery. Refer to Section “BATTERY REMOVAL”.

2.Remove battery caps. Check fluid level.

3.Add water only to bring fluid to proper level – approximately 3/16” above plates.

DO NOT OVERFILL.

4.Reinstall battery. Refer to Section “BATTERY INSTALLATION”.

3.3.3. MOWER DECK LEVELNESS

Check mower deck for proper level. Adjust as required. Refer to Section “MOWER DECK ADJUSTMENT – LEVELNESS”.

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

3.3.4. CLEAN MOWER DECK

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Clean underside of mower deck, removing all accumulation of grass clippings and debris.

5.Clean top of deck, removing all grass clippings and debris.

3.3.5MOWER BLADE SPINDLE - LUBRICATION 1. Follow WARNING statement found on this page.

2. Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “FUEK TANK REMOVAL”. If 3/4 or less, proceed to next step.

3. Carefully stand Rear Engine Rider on rear bumper.

4. Lubricate spindle with three shots of general purpose grease from grease gun. See Figure 3.5.

IMPORTANT: If the Rear Engine Rider will be on its rear bumper for longer than two hours, remove the battery. Refer to Section “BATTERY REMOVAL”.

3.3.6.MOWER DECK LINKAGE - LUBRICATION Lubricate all mower deck linkage pivot points with a light coat of motor oil.

SPINDLE

GREASE

FITTING

FIGURE 3.5

(Continued on next page)

17

Image 17
Contents Manual No -4391 I.R /19/01 European Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionFamiliarization Decals / Symbols Lowest Height CUT Battery Caution PRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartEngine Manual Start Starting & OperationEngine Electric Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineDo not park machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Reverse Lockout Mechanism Override Reverse Lockout MechanismService Engine AIR Cleaner Check Mower Blade Service After First 5 Hours Change Engine OILBlade Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltService Brake / Park Brake Battery Fluid Level Service Every 25 Operating HoursClean Mower Deck Interlock SystemRear Axle Bearing Lubrication Service Every 25 Operating Hours from previousFront Wheel Bearing Lubrication Engine Service AnnuallyFuel Filter Every TWO YearsRemoving Fuel Tank Storage OUT of SeasonMower Drive Belt Adjustment for 28 Decks only Engine Adjustments & RepairMower Deck Adjustment Side-To-Side Levelness Blade Brake AdjustmentFront to Rear Levelness 28 & 33 Decks Mower Deck AdjustmentChain Case Clutch Yoke Cable Housing Spring Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsBelt Replacement Blade Drive Belt ReplacementBelt Removal DecksBattery Installation Battery Battery RemovalBattery Storage Battery ServiceNEW Battery Preparation 1. Remove battery from carton Battery TestingSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionBlades Not Cutting Loss Of TractionCutting Grass ImproperlyTo be Performed Pages Subject Service ReferenceMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyService Notes European Rear Engine Riding Mower Series

E281022BE, E281222BE, E331522KVE, E331522KVE, E281022BE, E281222BE, E281222BE, E281022BE, E331522KVE specifications

The Snapper E281222BE, E281022BE, and E331522KVE models are part of Snapper’s extensive range of outdoor power equipment, known for their reliability and innovative features. These models are designed to cater to the needs of homeowners and professional landscapers alike, providing efficient and effective solutions for lawn care.

Starting with the Snapper E281222BE, this model stands out with its 21-inch cutting deck, which facilitates a wider cutting path, reducing mowing time. It is equipped with a powerful Briggs & Stratton engine that delivers strong performance, allowing for efficient cutting through various types of grass and terrain. The E281222BE also features a 3-in-1 mowing system, enabling users to mulch, bag, or side discharge grass clippings, offering versatility depending on the user's preference and yard conditions.

Next in line, the Snapper E281022BE presents a similar design but with slight modifications geared towards providing an economical and efficient solution for smaller lawns. This model also has a 21-inch cutting deck and shares the robust engine characteristics of its counterpart. However, it’s particularly known for its lightweight construction, making it easier to maneuver around tight spaces and flower beds. The E281022BE promotes excellent grass management with its easy-to-use height adjustment system that allows for customized cutting heights.

The E331522KVE model, on the other hand, offers additional features aimed at enhancing user experience. It boasts a larger 33-inch cutting deck, making it ideal for medium to large lawns. This model is powered by a powerful engine designed for high performance, while its variable-speed drive system allows for greater control over mowing speed. Furthermore, the E331522KVE integrates advanced technologies such as Smart-Cut™ technology, which adjusts power and speed automatically according to grass conditions, ensuring efficient grass management in varying scenarios.

All models feature durable construction with weather-resistant components, making them reliable choices for all seasons. Ergonomically designed handles and easy-to-access controls ensure comfort during extended use. Snapper’s commitment to sustainability is reflected in these models, as they are designed to maintain optimal fuel efficiency while minimizing emissions.

In conclusion, Snapper's E281222BE, E281022BE, and E331522KVE models offer a blend of power, efficiency, and ease of use. These characteristics make them suitable for various lawn care tasks while catering to the specific needs of the user. Whether you’re maintaining a small residential lawn or managing larger grassy areas, these Snapper models provide the performance and features necessary to achieve a beautifully manicured landscape.