Snapper E281022BE, E281222BE, E331522KVE Blade Drive Belt Replacement, Belt Removal, Decks

Page 26

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

4.5BLADE DRIVE BELT REPLACEMENT

Inspect mower drive belt as described in Section “CHECK MOWER DRIVE BELT”. Replace belt if signs of excessive wear and/or damage are present.

4.5.1. BELT REMOVAL

1.Remove mower drive belt cover. Refer to Section “DRIVE BELT COVER REMOVAL”.

2.Remove old belt.

4.5.2. BELT REPLACEMENT

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Route new belt through engine belt guide up to engine pulley. See Figure 4.14.

ENGINE PULLEY

ENGINE

BELT

GUIDE

FIGURE 4.14

5.Move transmission shift lever to the neutral (N) position.

6.Rotate clutch yoke (clutch yoke shown in Figure 4.9) out with your hand and work belt between drive disc and rubber driven disc.

7.To clear the primary chain case, move transmission shift lever to the #5 position. Route belt around drive disc and into drive pulley belt groove.

8.Remove idler. See Figure 4.15 and 4.16

9.Route belt onto spindle pulley. Make sure belt is inside spindle belt guide and idler belt guide. Route belt as shown in Figure 4.15 or 4.16.

10.Reinstall idler removed in Step 8. The idler belt guide tab should be positioned in the hole located on idler arm. Tighten idler pulley bolt securely.

11.Adjust belt guide. See Figure 4.15 or 4.16 for proper belt-to-belt guide clearances.

12.Check mower drive belt tension and adjust if necessary (28” deck only). Refer to Section “MOWER DRIVE BELT ADJUSTMENT”.

13.Reinstall mower drive belt cover.

28” DECKS

IDLER BELT GUIDE

1/16” NOMINAL

REMOVE IDLER

FIGURE 4.15

33” DECKS

33” MODELS

(DUAL IDLER SYSTEM)

1/16” NOMINAL

REMOVE IDLER

FIGURE 4.16

26

Image 26
Contents European Rear Engine Riding Mower Series Manual No -4391 I.R /19/01Important Safety Instructions Operation Table of Contents Introduction NomenclatureFamiliarization Decals / Symbols Lowest Height CUT Battery Caution OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Manual Start Starting & OperationEngine Electric Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeDo not park machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideService After First 5 Hours Change Engine OIL Service Engine AIR Cleaner Check Mower BladeBlade Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltService Brake / Park Brake Clean Mower Deck Service Every 25 Operating HoursBattery Fluid Level Interlock SystemRear Axle Bearing Lubrication Service Every 25 Operating Hours from previousFront Wheel Bearing Lubrication Fuel Filter Service AnnuallyEngine Every TWO YearsStorage OUT of Season Removing Fuel TankEngine Adjustments & Repair Mower Drive Belt Adjustment for 28 Decks onlyBlade Brake Adjustment Mower Deck Adjustment Side-To-Side LevelnessMower Deck Adjustment Front to Rear Levelness 28 & 33 DecksChain Case Clutch Yoke Cable Housing Spring Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBelt Removal Blade Drive Belt ReplacementBelt Replacement DecksBattery Battery Removal Battery InstallationNEW Battery Preparation 1. Remove battery from carton Battery ServiceBattery Storage Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopCutting Grass Loss Of TractionBlades Not Cutting ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyService Notes European Rear Engine Riding Mower Series

E281022BE, E281222BE, E331522KVE, E331522KVE, E281022BE, E281222BE, E281222BE, E281022BE, E331522KVE specifications

The Snapper E281222BE, E281022BE, and E331522KVE models are part of Snapper’s extensive range of outdoor power equipment, known for their reliability and innovative features. These models are designed to cater to the needs of homeowners and professional landscapers alike, providing efficient and effective solutions for lawn care.

Starting with the Snapper E281222BE, this model stands out with its 21-inch cutting deck, which facilitates a wider cutting path, reducing mowing time. It is equipped with a powerful Briggs & Stratton engine that delivers strong performance, allowing for efficient cutting through various types of grass and terrain. The E281222BE also features a 3-in-1 mowing system, enabling users to mulch, bag, or side discharge grass clippings, offering versatility depending on the user's preference and yard conditions.

Next in line, the Snapper E281022BE presents a similar design but with slight modifications geared towards providing an economical and efficient solution for smaller lawns. This model also has a 21-inch cutting deck and shares the robust engine characteristics of its counterpart. However, it’s particularly known for its lightweight construction, making it easier to maneuver around tight spaces and flower beds. The E281022BE promotes excellent grass management with its easy-to-use height adjustment system that allows for customized cutting heights.

The E331522KVE model, on the other hand, offers additional features aimed at enhancing user experience. It boasts a larger 33-inch cutting deck, making it ideal for medium to large lawns. This model is powered by a powerful engine designed for high performance, while its variable-speed drive system allows for greater control over mowing speed. Furthermore, the E331522KVE integrates advanced technologies such as Smart-Cut™ technology, which adjusts power and speed automatically according to grass conditions, ensuring efficient grass management in varying scenarios.

All models feature durable construction with weather-resistant components, making them reliable choices for all seasons. Ergonomically designed handles and easy-to-access controls ensure comfort during extended use. Snapper’s commitment to sustainability is reflected in these models, as they are designed to maintain optimal fuel efficiency while minimizing emissions.

In conclusion, Snapper's E281222BE, E281022BE, and E331522KVE models offer a blend of power, efficiency, and ease of use. These characteristics make them suitable for various lawn care tasks while catering to the specific needs of the user. Whether you’re maintaining a small residential lawn or managing larger grassy areas, these Snapper models provide the performance and features necessary to achieve a beautifully manicured landscape.