Snapper E331522KVE, E281022BE, E281222BE Service Annually, Engine, Fuel Filter, Every TWO Years

Page 19

Section 3 - MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

3.3SERVICE - EVERY 25 OPERATING HOURS 3.3.9. DIFFERENTIAL/CHAIN CASE - LUBRICATION 3. Check fill/level plug for damage. If signs of wear or cracks are visible, replace plug with new plug. See Figure 3.9.

4.To check lubricant in chain case, remove fill/level plug and look for lubricant on the internal components of the chain case. If no lubricant is visible, add "SNAPPER Transmission” grease as needed. See Figure 3.9.

AXLE

BOOTS

CHAIN

CASE

FILL/LEVEL PLUG

P.N. 1-1024

FIGURE 3.9

3.3.10.Check “MAINTENANCE SCHEDULE” Section of Engine Owner’s Manual for additional engine service.

3.4SERVICE - ANNUALLY

3.4.1.Perform all maintenance as specified in “MAINTENANCE SCHEDULE” Section of this manual.

3.4.2.ENGINE

Perform all maintenance as specified in Engine Owner’s Manual.

3.4.3. FUEL FILTER

Service fuel filter as instructed below, on COLD ENGINE ONLY!

IMPORTANT: To stop flow of fuel, tank may be removed from bracket and set on the floor so the fuel level will be below the filter. Refer to Section “REMOVING FUEL TANK”.

1.Remove hose clamps from fuel filter.

2.Remove fuel lines from filter. Discard filter.

3.Install new fuel filter. See Figure 3.10.

4.Reinstall fuel tank into bracket.

HOSE

CLAMPS

FUEL

FILTER

P.N. 1-4359

FIGURE 3.10

3.5EVERY TWO YEARS

In addition to regular maintenance, the following components of the Rear Engine Rider should be carefully inspected every two years for wear or damage. Replace worn or damaged parts with genuine SNAPPER replacement parts available from an authorized SNAPPER dealer.

3.5.1.All bushings and pivot areas.

3.5.2.Check both front wheel king pins.

3.5.3.Transmission shift lever and detent.

3.5.4.Clutch disc.

3.5.5.Clutch Yoke (See Figure 4.9).

3.5.6.Mower deck linkage and pivot areas.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Manual No -4391 I.R /19/01 European Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionFamiliarization Decals / Symbols Lowest Height CUT Battery Caution PRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartEngine Electric Start Starting & OperationEngine Manual Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Cutting Height AdjustmentDo not park machine on slopes Reverse Lockout Mechanism Override Reverse Lockout MechanismService Engine AIR Cleaner Check Mower Blade Service After First 5 Hours Change Engine OILService Brake / Park Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltBlade Brake Interlock System Service Every 25 Operating HoursBattery Fluid Level Clean Mower DeckFront Wheel Bearing Lubrication Service Every 25 Operating Hours from previousRear Axle Bearing Lubrication Every TWO Years Service AnnuallyEngine Fuel FilterRemoving Fuel Tank Storage OUT of SeasonMower Drive Belt Adjustment for 28 Decks only Engine Adjustments & RepairMower Deck Adjustment Side-To-Side Levelness Blade Brake AdjustmentFront to Rear Levelness 28 & 33 Decks Mower Deck AdjustmentChain Case Clutch Yoke Cable Housing Spring Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsDecks Blade Drive Belt ReplacementBelt Replacement Belt RemovalBattery Installation Battery Battery RemovalBattery Testing Battery ServiceBattery Storage NEW Battery Preparation 1. Remove battery from cartonSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionImproperly Loss Of TractionBlades Not Cutting Cutting GrassTo be Performed Pages Subject Service ReferenceMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyService Notes European Rear Engine Riding Mower Series

E281022BE, E281222BE, E331522KVE, E331522KVE, E281022BE, E281222BE, E281222BE, E281022BE, E331522KVE specifications

The Snapper E281222BE, E281022BE, and E331522KVE models are part of Snapper’s extensive range of outdoor power equipment, known for their reliability and innovative features. These models are designed to cater to the needs of homeowners and professional landscapers alike, providing efficient and effective solutions for lawn care.

Starting with the Snapper E281222BE, this model stands out with its 21-inch cutting deck, which facilitates a wider cutting path, reducing mowing time. It is equipped with a powerful Briggs & Stratton engine that delivers strong performance, allowing for efficient cutting through various types of grass and terrain. The E281222BE also features a 3-in-1 mowing system, enabling users to mulch, bag, or side discharge grass clippings, offering versatility depending on the user's preference and yard conditions.

Next in line, the Snapper E281022BE presents a similar design but with slight modifications geared towards providing an economical and efficient solution for smaller lawns. This model also has a 21-inch cutting deck and shares the robust engine characteristics of its counterpart. However, it’s particularly known for its lightweight construction, making it easier to maneuver around tight spaces and flower beds. The E281022BE promotes excellent grass management with its easy-to-use height adjustment system that allows for customized cutting heights.

The E331522KVE model, on the other hand, offers additional features aimed at enhancing user experience. It boasts a larger 33-inch cutting deck, making it ideal for medium to large lawns. This model is powered by a powerful engine designed for high performance, while its variable-speed drive system allows for greater control over mowing speed. Furthermore, the E331522KVE integrates advanced technologies such as Smart-Cut™ technology, which adjusts power and speed automatically according to grass conditions, ensuring efficient grass management in varying scenarios.

All models feature durable construction with weather-resistant components, making them reliable choices for all seasons. Ergonomically designed handles and easy-to-access controls ensure comfort during extended use. Snapper’s commitment to sustainability is reflected in these models, as they are designed to maintain optimal fuel efficiency while minimizing emissions.

In conclusion, Snapper's E281222BE, E281022BE, and E331522KVE models offer a blend of power, efficiency, and ease of use. These characteristics make them suitable for various lawn care tasks while catering to the specific needs of the user. Whether you’re maintaining a small residential lawn or managing larger grassy areas, these Snapper models provide the performance and features necessary to achieve a beautifully manicured landscape.
Top Page Image Contents