Snapper E281222BE, E281022BE, E331522KVE, E331522KVE, E281022BE, E281222BE Operation

Page 3

IMPORTANT SAFETY INSTRUCTIONS

PREPARATION

(Continued From Previous Page)

7.Keep people and pets out of mowing area. Immediately STOP blades, STOP engine, and STOP machine if anyone enters the area.

8.Check shields, deflectors, switches, blade controls and other safety devices frequently for proper operation and location.

9.Make sure all safety decals are clearly legible. Replace if damaged.

10.Protect yourself when mowing and wear safety glasses, long pants and substantial footwear.

11.Know how to STOP blades and engine quickly in preparation for emergencies.

12.Use extra care when loading or unloading the machine into a trailer or truck.

13.Check grass catcher components frequently for signs of wear or deterioration and replace as needed to prevent injury from thrown objects going through weak or worn spots.

OPERATION

1.Mount and dismount machine from left side.

2.Start engine from operator's seat, if possible. Make sure blades are OFF and parking brake is set.

3.DO NOT leave machine with engine running. STOP engine, STOP blades, SET brake, and Remove key before leaving operators position of any reason.

4.DO NOT operate machine unless properly seated with feet on feet rests or pedal(s).

5.STOP BLADES and ENGINE and make sure blades have stopped before removing grass catcher or unclogging mower to prevent loss of fingers or hand.

6.Blades must be OFF except when cutting grass. Set blades in highest position when mowing over rough ground.

7.Keep hands and feet away from rotating blades underneath deck. DO NOT place foot on ground while BLADES are ON or machine is in motion.

8.DO NOT operate machine without entire grass catcher or guards in place. DO NOT point discharge at people, passing cars, windows or doors.

9.Slow down before turning.

10.Watch out for traffic when near or crossing roadways.

11.STOP engine immediately after striking an obstruction. Inspect machine and repair damage before resuming operation.

12.Operate machine only in daylight or with good artificial light.

13.Move joystick (if equipped) SLOWLY to maintain control during speed and directional changes.

OPERATION

(Continued From Previous Column)

14.Exercise CAUTION when pulling loads. Limit loads to those you can safely control and attach loads to hitch plate as specified with SNAPPER attachment instructions.

15.DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, a deadly poison.

MAINTENANCE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of children in a well ventilated, unoccupied building.

2.Keep engine free of grass, leaves or excess grease to reduce fire hazard and engine overheating.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Check brakes frequently; adjust, repair or replace as needed.

5.Keep all bolts, nuts and screws properly tight. Check that all cotter pins are in proper position.

6.Always provide adequate ventilation when running engine. Exhaust gases contain carbon monoxide, an odorless and deadly poison.

7.Disconnect negative (black) cable from battery before performing maintenance or service. Cranking engine could cause injury.

8.DO NOT work under machine without safety blocks.

9.Service engine and make adjustments only when engine is stopped. Remove spark plug wire(s) from spark plug(s) and secure wire(s) away from spark plug(s).

10.DO NOT change engine governor speed settings or overspeed engine.

11.Lubricate machine at intervals specified in manual to prevent controls from binding.

12.Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them.

13.DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.

14.Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices.

15.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Manual No -4391 I.R /19/01 European Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionFamiliarization Decals / Symbols Lowest Height CUT Battery Caution PRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartStarting & Operation Engine Electric StartEngine Manual Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineCutting Height Adjustment Stopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park BrakeDo not park machine on slopes Reverse Lockout Mechanism Override Reverse Lockout MechanismService Engine AIR Cleaner Check Mower Blade Service After First 5 Hours Change Engine OILService After First 5 Hours 3.2.4. Check Blade Drive Belt Service Brake / Park BrakeBlade Brake Interlock System Service Every 25 Operating HoursBattery Fluid Level Clean Mower DeckService Every 25 Operating Hours from previous Front Wheel Bearing LubricationRear Axle Bearing Lubrication Every TWO Years Service AnnuallyEngine Fuel FilterRemoving Fuel Tank Storage OUT of SeasonMower Drive Belt Adjustment for 28 Decks only Engine Adjustments & RepairMower Deck Adjustment Side-To-Side Levelness Blade Brake AdjustmentFront to Rear Levelness 28 & 33 Decks Mower Deck AdjustmentChain Case Clutch Yoke Cable Housing Spring Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsDecks Blade Drive Belt ReplacementBelt Replacement Belt RemovalBattery Installation Battery Battery RemovalBattery Testing Battery ServiceBattery Storage NEW Battery Preparation 1. Remove battery from cartonSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionImproperly Loss Of TractionBlades Not Cutting Cutting GrassTo be Performed Pages Subject Service ReferenceMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyService Notes European Rear Engine Riding Mower Series

E281022BE, E281222BE, E331522KVE, E331522KVE, E281022BE, E281222BE, E281222BE, E281022BE, E331522KVE specifications

The Snapper E281222BE, E281022BE, and E331522KVE models are part of Snapper’s extensive range of outdoor power equipment, known for their reliability and innovative features. These models are designed to cater to the needs of homeowners and professional landscapers alike, providing efficient and effective solutions for lawn care.

Starting with the Snapper E281222BE, this model stands out with its 21-inch cutting deck, which facilitates a wider cutting path, reducing mowing time. It is equipped with a powerful Briggs & Stratton engine that delivers strong performance, allowing for efficient cutting through various types of grass and terrain. The E281222BE also features a 3-in-1 mowing system, enabling users to mulch, bag, or side discharge grass clippings, offering versatility depending on the user's preference and yard conditions.

Next in line, the Snapper E281022BE presents a similar design but with slight modifications geared towards providing an economical and efficient solution for smaller lawns. This model also has a 21-inch cutting deck and shares the robust engine characteristics of its counterpart. However, it’s particularly known for its lightweight construction, making it easier to maneuver around tight spaces and flower beds. The E281022BE promotes excellent grass management with its easy-to-use height adjustment system that allows for customized cutting heights.

The E331522KVE model, on the other hand, offers additional features aimed at enhancing user experience. It boasts a larger 33-inch cutting deck, making it ideal for medium to large lawns. This model is powered by a powerful engine designed for high performance, while its variable-speed drive system allows for greater control over mowing speed. Furthermore, the E331522KVE integrates advanced technologies such as Smart-Cut™ technology, which adjusts power and speed automatically according to grass conditions, ensuring efficient grass management in varying scenarios.

All models feature durable construction with weather-resistant components, making them reliable choices for all seasons. Ergonomically designed handles and easy-to-access controls ensure comfort during extended use. Snapper’s commitment to sustainability is reflected in these models, as they are designed to maintain optimal fuel efficiency while minimizing emissions.

In conclusion, Snapper's E281222BE, E281022BE, and E331522KVE models offer a blend of power, efficiency, and ease of use. These characteristics make them suitable for various lawn care tasks while catering to the specific needs of the user. Whether you’re maintaining a small residential lawn or managing larger grassy areas, these Snapper models provide the performance and features necessary to achieve a beautifully manicured landscape.
Top Page Image Contents