Snapper SGT27540D manual Regular Maintenance, Clean Radiator, Clean Transmission Oil Cooler

Page 28

Regular Maintenance

Engine Maintenance - General

Refer to the engine owner’s manual for all engine main- tenance procedures and recommendations.

Clean Debris Out of Engine

Compartment

Service Interval: Every 25 Hours, or As Necessary

Stop the engine and allow the unit to cool. Remove all debris from the engine compartment. Be sure all cooling fins, radiators, screens, and areas around the exhaust system are clean.

WARNING

Keep the unit free of grass, leaves, and other debris. Flammable debris many be ignited by hot engine parts causing serious injury or property damage.

Clean Radiator

Service Interval: Every 25 Hours, or As Necessary

Clean the radiator, or radiator screen with compressed air at regular intervals, or if dirty. The radiator is located at the rear of the engine compartment on liquid-cooled models. Liquid cooled models also have a removable radiator screen (F, Figure 24). Clean all cooling system components.

Clean Transmission Oil Cooler

Service Interval: Every 25 Hours, or As Necessary

The transmission oil cooler (C, Figures 24) is located behind the engine and should be cleaned with com- pressed air at regular intervals or if dirty.

Check Engine Coolant Level

Service Interval: Every 25 Hours, or As Necessary

The engine coolant level and quality should be checked before each use, when the engine is off and cool.

1.Check the coolant level in the overflow reservoir (A, Figure 24). Coolant should be between the “H” and “L” marks on the tank.

2.If the coolant level is below the “L” mark on the over- flow reservoir, add coolant by shutting off the engine, allowing the engine to cool, removing the reservoir cap, and adding coolant. Proper coolant mix is a 50/50 mixture of ethylene glycol and distilled water.

Change Engine Coolant

See Engine Manual for antifreeze recommendations and change intervals. See Figures 24 for drain plug locations.

B

C

 

D

 

 

 

 

 

 

 

 

A

 

 

 

E

 

 

 

 

 

 

I

H

F

J

K

G

 

 

 

Figure 24. Engine

A.Coolant Reservoir

B.Engine Oil Fill

C.Transmission Oil Cooler

D.Radiator Fill Cap

E.Fuel Filter / Water Separator

F.Radiator Screen

G.Radiator Drain Plug

H.Oil Filter

I.Oil Dipstick

J.Air Filter

K.Oil Drain Plug (Bottom of Engine)

26

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Mower Decks 27HP Hydro Tractors & Mower DecksMfg. No. Description Page Table of Contents Safety Rules & Information Operating Safety Safety Rules and Information Slope OperationSafety Rules & Information General OperationIgnition System Service & Maintenance Safe Handling of GasolineCE Identification Tag Markings Identification NumbersTractor ID Tag Mower ID Tag Safety Decals Safety DecalsDecal PTO Selector Positions Decal Danger, Rotating Fan CE, Diesel ModelsSafety Icons Operational Safety ChecksControl Functions Features & Controls Parking Brake Function Automatic Controlled TractionDashboard Display Functions General Operating Safety Slope OperationAdding Fuel Stopping The Tractor & EngineOperating the Tractor Using Inboard Hydraulics Pushing The Tractor By HandHydraulic System Functions GeneralUsing Auxiliary Hydraulics Auxiliary Hydraulics Angle Left Angle RightOptional 3-Point Hitch Operation Select Models Attachment Weight LimitLocking The Hitch Hitch Arms Installation Connecting a Drive Shaft Rear PTO Operation Select ModelsChecks Before Starting Starting & Stopping the PTOAttachment Recommendations Mower Deck Removal & Installation Removing the Mower DeckInstalling the Mower Deck Mower Electrical ConnectionAttaching a Trailer Volt Power OutletStorage Regular Maintenance Before Every Spring Each Hours Fall UseRegular Maintenance Clean RadiatorClean Transmission Oil Cooler Check Engine Coolant LevelService Interval Seasonally or as Needed Drain Fuel SeparatorService Interval Every 25 Hours Check Transmission Oil LevelCheck Front Axle Oil Level Change Transmission Oil & filterOil Filter Part No Safety Interlock System Check Service Interval Every Fall & SpringService Interval Every 100 Hours or Fall & Spring Check Mower Deck Gear Box OilBattery Maintenance Cleaning the Battery and CablesCheck Tire Pressures Size TreadGrease LubricationOil Grease the Electric Lift Rod GreaseFitting Yearly Arm Grease Fitting YearlyServicing The Mower Blades Removing the BladeMaintenance Records Troubleshooting Adjustment, & Service Troubleshooting the Mower Troubleshooting, Adjustment, & Service Seat AdjustmentBrake Adjustment Seat Slide AdjustmentTaillight & Dash Light Replacement Headlight ReplacementBattery Charging Mower Adjustments Gauge Wheel AdjustmentSide-to-Side Adjustment Lock Nut, 5/16-18 Spacer Bolt Leveling The MowerMower Drive Belt Replacement Mower Belt ReplacementTo avoid damaging belts, do not PRY Specifications 27 HP* Briggs & StrattonReplacement Parts Maintenance ItemsOptional Accessories Technical Manuals

SGT27540D specifications

The Snapper SGT27540D is a robust and versatile lawn mower designed to cater to both residential and light commercial users. This model, known for its efficiency and ease of use, combines advanced technology with practical features, making yard maintenance a seamless task.

One of the standout features of the SGT27540D is its powerful 27 horsepower engine, which provides ample power for tackling various types of terrain and grass conditions. The engine’s design incorporates advanced cooling and lubrication systems, ensuring longevity and reduced maintenance needs. This lawn mower also features a self-propelled drive system, which allows users to effortlessly navigate through their yards without straining themselves.

The Snapper SGT27540D is equipped with a 54-inch cutting deck, facilitating a wide cutting swath that can efficiently cover large expanses of grass in a short amount of time. This deck features a robust steel construction for durability, and the adjustable cutting height offers versatility, allowing users to choose the perfect blade height based on their lawn’s requirements.

One of the defining technologies in the SGT27540D is the signature Snapper HiVac mowing system. This technology optimizes grass lifting, ensuring that even the toughest mowing jobs result in a clean and precise cut. As an added bonus, the HiVac system also improves grass clipping collection, making post-mowing cleanup a breeze.

Another notable characteristic of the Snapper SGT27540D is its user-friendly controls. The ergonomically designed steering lever allows for intuitive operation, while the dashboard provides essential information about speed and engine performance. For added comfort, the mower features an adjustable seat that can accommodate users of different heights.

The safety of operators is also a priority in the design of the SGT27540D. It is equipped with a reliable blade brake system that halts the blades quickly when necessary, minimizing the risk of accidents.

In summary, the Snapper SGT27540D is an exemplary lawn mower that marries durable construction with advanced technology. Its powerful engine, efficient cutting system, and user-friendly design make it a preferred choice for anyone seeking to maintain a pristine lawn with minimal effort and maximum results.
Top Page Image Contents