Snapper 150Z Parts and Belt Diagram: Mower Deck Removal and Installation Guide

Page 16

MOWER DECK REMOVAL &

INSTALLATION

NOTE: Perform mower removal and installation on a hard, level surface such as a concrete floor.

WARNING

Engage parking brake, disengage PTO, stop engine and remove key before attempting to install or remove the mower.

Removing the Mower Deck

1.Turn the PTO off, put the control levers in PARK posi- tion, turn the ignition OFF, remove the key, and wait for all moving parts to stop.

2.Pivot the rider’s front wheels forward.

3.Place the cutting height adjustment crank (D, Figure 10) in the lowest cutting position.

4.Release tension on the drive belt using the mower belt release lever (E, Figure 10) and remove the drive belt from the engine pulley.

5.Disconnect the front hitch by removing the hitch rod and clip (A, Figures 10 & 11), and lifting the mower hitch (B) up and off the rider hitch bracket (D).

6.Slide the mower deck forward until the rear mower supports (C) disengage the frame of the rider.

7.Slide the mower deck out from under the right side of the rider.

Installing the Mower Deck

1.Pivot the rider’s front wheels forward.

2.Place the cutting height adjustment crank (D, Figure 10) in the lowest cutting position.

3.Slide the mower deck under the right side of the rider. Slide the mower backwards making sure that the rear mower supports (C, Figure 11) slide up the ramps on the frame. The rear of the mower is supported by these frame ramps.

4.Hang the mower hitch (B, Figure 11) on the rider hitch bracket (D) and secure with the hitch rod and clip (A).

5.Use the mower belt release lever (D, Figure 12) to release tension on the mower idler pulley, and install the drive belt as shown in Figure 12.

D

C

A

BE

Figure 10. Mower Components

A.Hitch Rod and Clip

B.Mower Hitch

C.Rear Mower Supports

D.Cutting Height Adjustment Crank

E.Mower Belt Release Lever

C

D

B A

Figure 11. Mower Hitch Components

A.Hitch Rod and Clip

B.Mower Hitch

C.Rear Mower Supports

D.Rider Hitch Bracket

 

B

C

A

 

 

C

E

D

E

Figure 12. Mower Belt Routing

A.Engine Pulley

B.Mower Drive Belt

C.Back-Side Idler Pulleys

D.Mower Belt Release Lever

E.Arbor Pulleys

14

Image 16
Contents OPERATOR’S Manual Mfg. No DescriptionPage Table of Contents Safety Rules General OperationIgnition System Service & Maintenance Safe Handling of GasolineSafety & Operation Decals Identification Numbers North AmericanCE Models OnlyPRE-OPERATION Read The Operator’s ManualOperation Control FunctionsGround Speed Levers Parking Brake Throttle ControlGeneral Operating Safety Checks Before Starting Fuel RecommendationsEmergency Stopping Stopping the Rider & EngineStarting the Engine MowingDriving Practice Smooth TravelForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Practice Turning In PlaceExecuting Turns Executing an End-Of-Row Zero TurnInstalling the Mower Deck Mower Deck Removal InstallationRemoving the Mower Deck Maintenance Maintenance ScheduleRider MAINTENANCE, All Models 18.5HP Briggs & StrattonClean Debris from Engine Cooling Areas and AIR Filter Clean Debris from Rider and Engine CompartmentCheck Tire Pressure Grease LubricationOil Clean Deck Check / Replace Mower Blades Blade RemovalCheck Rider Safety System Cleaning the Battery and CablesOperational Safety Checks Check / Adjust PTO Clutch Adjust PTO Clutch Window Adjustment Nut Feeler GaugeChange Engine OIL Check Engine OIL LevelChange Engine OIL & Filter AIR Filter & PRE-CLEANER Air Filter Removal & InstallationAir Filter Service Pre-Cleaner Pre-Cleaner ServiceReplace Spark Plug Ground Speed Control Lever Adjustment Service & AdjustmentsSpeed Balancing Adjustment Cutting Height Adjustment PTO Clutch AdjustmentBrake Adjustment Battery ChargingMower Deck Leveling Adjustments Side to Side LevelingMower Drive Belt Replacement Mower Belt ReplacementFront To Back Leveling Storage StorageTroubleshooting Troubleshooting the RiderTroubleshooting the Mower Dimensions EngineChassis TransmissionPage Page RO D U C T S