Cub Cadet SLTX1054 warranty Adjustments, Deck Spindle, Leveling the Deck Front To Rear

Page 22

Deck Spindle

Grease fittings can be found on each deck spindle. See Fig. 6-4. Lubricate with 251H EP grease or an equivalent No. 2 multi- purpose lithium grease. Using a grease gun, apply two strokes (minimum) or sufficient grease to the spindle shaft.

Figure 6-4

Adjustments

WARNING! Shut the engine off, remove the ignition key and engage the parking brake before making adjustments. Protect your hands by using

heavy gloves when handling the blades.

NOTE: Check the tractor’s tire pressure before performing any deck leveling adjustments. Refer to Tires on page 27 for information regarding tire pressure.

Leveling the Deck (Front To Rear)

The front of the cutting deck is supported by a stabilizer bar that can be adjusted to level the deck from front to rear. The front of the deck should be between 1⁄4” and 3⁄8” lower than the rear of the deck. Adjust if necessary as follows:

1.Park the tractor on a firm, level surface and place the deck lift lever in the top notch.

2.Rotate the blade nearest the discharge chute so that it is parallel with the tractor.

3.Measure the distance from the front of the blade tip to the ground and the rear of the blade tip to the ground. The first measurement taken should be between 1⁄4” and 3⁄8” less than the second measurement.

Determine the approximate distance necessary for proper adjustment and proceed, if necessary.

1.Loosen (thread outward) the hex lock nut on the end of the deck hanger rod. See Fig. 6-5.

Figure 6-5

2.To raise the front of the deck, tighten (thread inward) the inner hex nut against the front hanger bracket.

3.To lower the front of the deck, loosen (thread outward) the hex nut, away from the front hanger bracket. See Fig. 6-5.

4.Retighten the lock nut against the hex nut when proper adjustment is achieved.

22

Section 6 — Maintenance & Adjustments

Image 22
Contents Operator’s Manual Thank You Table of ContentsTo The Owner Record Product InformationImportant Safe Operation Practices California Proposition General OperationSlope Operation Do NotChildren ServiceGeneral Service TowingDo not modify engine Spark ArrestorSafety Symbols SymbolImportant Safe Operation Practices Contents of Crate Assembly & Set-UpTractor Set-Up Setting the Deck Gauge Wheels Connecting the Battery CablesChecking Tire Pressure Adjusting the Seat Gas and OilBrake Pedal Controls and FeaturesSeat Adjustment Lever Throttle/Choke Control LeverDeck Lift Lever Ignition Switch ModuleSystems Indicator Monitor/Hour Meter LCD Drive PedalPTO / Blade Engage Knob Fuel Level IndicatorParking Brake/Cruise Control Lever Starting the Engine Safety Interlock SwitchesOperation Stopping the EngineReverse Caution Mode Driving The TractorDriving On Slopes Engaging the Parking Brake Setting the Cruise ControlUsing the Deck Lift Lever Operating the HeadlightsOnoff MowingMaintenance Maintenance & AdjustmentsMaintenance Schedule Changing the Engine OilAir Cleaner Spark Plug Hydrostatic Transmission Cleaning the TractorSmart Jet Pivot Points & Linkage LubricationFront Wheels Deck WheelsDeck Spindle AdjustmentsLeveling the Deck Front To Rear Ball Joint Adjustment Gear Hex Bolt Steering AdjustmentParking Brake Adjustment Leveling the Deck Side to SideCutting Deck Removal ServiceInsert Ratchet Here Deck Idler Bracket Deck Lift Arm Deck Support Pin Cutting BladesFlange Lock Nut Block of Wood Jump Starting BatteryCharging Changing the Transmission Drive Belt FuseTires Changing the Deck Belt Hex Screws Belt Keeper RodOuter Spindle Pulleys PulleyPTO Belt Troubleshooting Problem Cause RemedyReplacement Parts Component Part Number and DescriptionComponent Part Number and DescriptionAttachments & Accessories Model Number DescriptionPage Your Warranty Rights and Obligations Vapor lines U.S.A Manual del Operador Índice Al propietarioGracias Registro de información de productoProposición 65 de California Medidas importantes de seguridadFuncionamiento general Haga lo siguiente Funcionamiento en pendientesNo haga lo siguiente Remolque ServicioNiños Manejo seguro de la gasolinaAviso referido a emisiones No modifique el motorGuardachispas Advertencia Superficie Caliente El poste de una empalizada Contenido del cajón Montaje y ConfiguraciónConfiguración del tractor Mover Manualmente el TractorControl de la presión de los neumáticos Instalación del cable de la bateríasAjuste de las ruedas de calibración de la plataforma Ajuste del asiento Gasolina y aceitePedal de freno Controles y CaracterísticasControl del regulador/cebador Palanca de ajuste del asientoPedal de la transmisión Módulo del interruptor de encendidoPedal de la marcha atrás Indicador de nivel de combustible Cargo NetoBatería Si el motor equipados Encendido del motor FuncionamientoDetención del motor Operación en pendientes Conducción del tractorBotón de Utilización de la palanca de elevación de la plataforma Corte de céspedFuncionamiento de los faros delanteros Colocación del freno de mano Activación del control de cruceroMantenimiento Mantenimiento y AjustesCalendario de mantenimiento MotorBujía de encendido Limpieza del tractorDepurador de aire Palanca de cambioPuntos de pivote y varillaje LubricaciónRuedas delanteras Ruedas de plataformaHusillo de plataforma AjustesNivelación de la plataforma adelante atrás Ajuste del volante Nivelación de la plataforma lado a ladoAjuste del freno de mano Engranaje De ajuste Perno HexagonalExtracción de la plataforma de corte ServicioInserte aquí Trinquete Soporte de la Cubierta Polea Cuchillas de corte Para retirar las cuchillas, haga lo siguienteArranque por medio de conexión en puente BateríaCarga de la batería Cambio de la correa de transmisión FusibleNeumáticos Cambio de la correa de la plataformaPTO Solución de Problemas Cebador no activadoEl motor vacila a altas Piezas de reemplazo ComponenteComponente Número de pieza y Descripción Aditamentos y Accesorios DescripciónSUS Derechos Y Obligaciones EN Cuanto a LA Garantía Líneas de vapor GDOC-100014 REV. B

SLTX1054 specifications

The Cub Cadet SLTX1054 is a robust riding lawn mower designed for homeowners seeking power, precision, and ease of use in lawn care. With its strong build and user-friendly features, this mowing machine stands out in the crowded market of garden equipment.

One of the key features of the SLTX1054 is its powerful 26-horsepower Kohler engine. This V-twin engine ensures efficient performance, offering plenty of torque for tough mowing jobs. The engine is designed with durability in mind, allowing for consistent performance over time, even in demanding conditions.

The 54-inch cutting deck is another notable aspect of the SLTX1054. This wide deck allows for expansive coverage, making it ideal for medium to large lawns. The deck is equipped with a combination of high-performance blades that deliver a clean cut, promoting healthier grass growth. With adjustable cutting heights ranging from 1.5 inches to 4 inches, homeowners can customize their mowing experience based on their lawn's specific needs.

The Cub Cadet SLTX1054 also showcases advanced technologies that enhance usability. The hydrostatic transmission offers smooth acceleration and effortless operation. This feature enables the operator to control the mower's speed with a simple push of the pedal, eliminating the need for gear shifting, which can be cumbersome on traditional lawn tractors.

Another highlight is the tight turning radius, which allows users to maneuver easily around flower beds, trees, and other obstacles. This agility reduces the need for additional trimming and provides a cleaner finish overall. The comfortable, adjustable high-back seat ensures an enjoyable driving experience for longer mowing tasks, reducing fatigue for the operator.

The SLTX1054 is also equipped with a dash-mounted deck lift, enabling users to raise and lower the mowing deck conveniently without leaving the driver's seat. This feature simplifies transitions between different cutting heights, making it easier to adapt to changing terrains.

Durability is a hallmark of the Cub Cadet brand, and the SLTX1054 is no exception. With its reinforced steel frame and rugged construction, this mower is built to withstand the rigors of regular lawn maintenance. Its tough, powder-coated finish adds an extra layer of protection against rust and corrosion.

In conclusion, the Cub Cadet SLTX1054 combines power, performance, and ease of use in a single package. With features like a robust engine, expansive cutting deck, hydrostatic transmission, and advanced maneuverability, this riding mower is a fantastic choice for homeowners looking to maintain their lawns efficiently and effectively. Whether tackling large lawns or navigating tight spaces, the SLTX1054 is up to the challenge.