Cub Cadet SLTX1054 Fuse, Tires Changing the Deck Belt, Changing the Transmission Drive Belt

Page 27

Fuse

WARNING! Before servicing, repairing, or inspecting, always disengage PTO, set parking brake, stop engine and remove key to prevent unintended starting.

A fuse is installed in your tractor’s wiring harness to protect the tractor’s electrical system from damage caused by excessive amperage.

If the electrical system does not function, or your tractor’s engine will not crank, check to be certain that the fuse has not blown. It is located under the hood, mounted behind the top of the dash panel on the support bar.

Caution: Always use a replacement fuse with the same amperage capacity as the blown fuse.

Tires

WARNING! Never exceed the maximum inflation pressure shown on the sidewall of the tire.

Changing the Deck Belt

WARNING! Shut the engine off and remove ignition key before removing the cutting blade(s) for sharpening or replacement. Protect your hands by

using heavy gloves when grasping blades and pulleys.

Warning! The V-belts found on your tractor are specially designed to engage and disengage safely. A substitute (non-OEM) V-belt can be dangerous by

not disengaging completely. For a proper working machine, use factory approved belts.

All belts on your tractor are subject to wear and should be replaced if any signs of wear are present. To change or replace the deck belt on your tractor, proceed as follows:

1.Remove the deck as instructed on page 24.

2.Remove the belt guards by removing the hex screws that fasten them to the deck. See Fig. 7-7.

Refer to the tire sidewall for exact tire manufacturer’s recommended or maximum psi. Do not overinflate.

Uneven tire pressure could cause the cutting deck to mow unevenly.

Changing the Transmission Drive Belt

Hex Screws

Belt Keeper Rod

Several components must be removed and special tools used in order to change the tractor’s transmission drive belt. See your Cub Cadet dealer to have the transmission drive belt replaced.

Deck Idler Pulley

Belt Guards

Figure 7-7

3.Loosen, but do not remove the belt keeper rod on the pulley located near the back of the deck. See Fig. 7-7.

4.Carefully remove the deck belt from around the three spindle pulleys and the two deck idler pulleys.

Section 7 — Service

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Operator’s Manual Record Product Information Table of ContentsTo The Owner Thank YouCalifornia Proposition General Operation Important Safe Operation PracticesDo Not Slope OperationTowing ServiceGeneral Service ChildrenSpark Arrestor Do not modify engineSymbol Safety SymbolsImportant Safe Operation Practices Assembly & Set-Up Contents of CrateTractor Set-Up Connecting the Battery Cables Setting the Deck Gauge WheelsChecking Tire Pressure Gas and Oil Adjusting the SeatThrottle/Choke Control Lever Controls and FeaturesSeat Adjustment Lever Brake PedalDrive Pedal Ignition Switch ModuleSystems Indicator Monitor/Hour Meter LCD Deck Lift LeverFuel Level Indicator PTO / Blade Engage KnobParking Brake/Cruise Control Lever Stopping the Engine Safety Interlock SwitchesOperation Starting the EngineDriving The Tractor Reverse Caution ModeOperating the Headlights Engaging the Parking Brake Setting the Cruise ControlUsing the Deck Lift Lever Driving On SlopesMowing OnoffChanging the Engine Oil Maintenance & AdjustmentsMaintenance Schedule MaintenanceCleaning the Tractor Air Cleaner Spark Plug Hydrostatic TransmissionSmart Jet Deck Wheels LubricationFront Wheels Pivot Points & LinkageAdjustments Deck SpindleLeveling the Deck Front To Rear Leveling the Deck Side to Side Steering AdjustmentParking Brake Adjustment Ball Joint Adjustment Gear Hex BoltService Cutting Deck RemovalInsert Ratchet Here Deck Idler Bracket Cutting Blades Deck Lift Arm Deck Support PinFlange Lock Nut Block of Wood Battery Jump StartingCharging Hex Screws Belt Keeper Rod FuseTires Changing the Deck Belt Changing the Transmission Drive BeltPulley Outer Spindle PulleysPTO Belt Problem Cause Remedy TroubleshootingComponent Part Number and Description Replacement PartsPart Number and Description ComponentModel Number Description Attachments & AccessoriesPage Your Warranty Rights and Obligations Vapor lines U.S.A Manual del Operador Registro de información de producto Al propietarioGracias ÍndiceMedidas importantes de seguridad Proposición 65 de CaliforniaFuncionamiento general Funcionamiento en pendientes Haga lo siguienteNo haga lo siguiente Manejo seguro de la gasolina ServicioNiños RemolqueNo modifique el motor Aviso referido a emisionesGuardachispas Advertencia Superficie Caliente El poste de una empalizada Mover Manualmente el Tractor Montaje y ConfiguraciónConfiguración del tractor Contenido del cajónInstalación del cable de la baterías Control de la presión de los neumáticosAjuste de las ruedas de calibración de la plataforma Gasolina y aceite Ajuste del asientoPalanca de ajuste del asiento Controles y CaracterísticasControl del regulador/cebador Pedal de frenoMódulo del interruptor de encendido Pedal de la transmisiónPedal de la marcha atrás Cargo Neto Indicador de nivel de combustibleBatería Si el motor equipados Funcionamiento Encendido del motorDetención del motor Conducción del tractor Operación en pendientesBotón de Corte de césped Utilización de la palanca de elevación de la plataformaFuncionamiento de los faros delanteros Activación del control de crucero Colocación del freno de manoMotor Mantenimiento y AjustesCalendario de mantenimiento MantenimientoPalanca de cambio Limpieza del tractorDepurador de aire Bujía de encendidoRuedas de plataforma LubricaciónRuedas delanteras Puntos de pivote y varillajeAjustes Husillo de plataformaNivelación de la plataforma adelante atrás Engranaje De ajuste Perno Hexagonal Nivelación de la plataforma lado a ladoAjuste del freno de mano Ajuste del volanteServicio Extracción de la plataforma de corteInserte aquí Trinquete Soporte de la Cubierta Polea Para retirar las cuchillas, haga lo siguiente Cuchillas de corteBatería Arranque por medio de conexión en puenteCarga de la batería Cambio de la correa de la plataforma FusibleNeumáticos Cambio de la correa de transmisiónPTO Cebador no activado Solución de ProblemasEl motor vacila a altas Componente Piezas de reemplazoComponente Número de pieza y Descripción Descripción Aditamentos y AccesoriosSUS Derechos Y Obligaciones EN Cuanto a LA Garantía Líneas de vapor GDOC-100014 REV. B

SLTX1054 specifications

The Cub Cadet SLTX1054 is a robust riding lawn mower designed for homeowners seeking power, precision, and ease of use in lawn care. With its strong build and user-friendly features, this mowing machine stands out in the crowded market of garden equipment.

One of the key features of the SLTX1054 is its powerful 26-horsepower Kohler engine. This V-twin engine ensures efficient performance, offering plenty of torque for tough mowing jobs. The engine is designed with durability in mind, allowing for consistent performance over time, even in demanding conditions.

The 54-inch cutting deck is another notable aspect of the SLTX1054. This wide deck allows for expansive coverage, making it ideal for medium to large lawns. The deck is equipped with a combination of high-performance blades that deliver a clean cut, promoting healthier grass growth. With adjustable cutting heights ranging from 1.5 inches to 4 inches, homeowners can customize their mowing experience based on their lawn's specific needs.

The Cub Cadet SLTX1054 also showcases advanced technologies that enhance usability. The hydrostatic transmission offers smooth acceleration and effortless operation. This feature enables the operator to control the mower's speed with a simple push of the pedal, eliminating the need for gear shifting, which can be cumbersome on traditional lawn tractors.

Another highlight is the tight turning radius, which allows users to maneuver easily around flower beds, trees, and other obstacles. This agility reduces the need for additional trimming and provides a cleaner finish overall. The comfortable, adjustable high-back seat ensures an enjoyable driving experience for longer mowing tasks, reducing fatigue for the operator.

The SLTX1054 is also equipped with a dash-mounted deck lift, enabling users to raise and lower the mowing deck conveniently without leaving the driver's seat. This feature simplifies transitions between different cutting heights, making it easier to adapt to changing terrains.

Durability is a hallmark of the Cub Cadet brand, and the SLTX1054 is no exception. With its reinforced steel frame and rugged construction, this mower is built to withstand the rigors of regular lawn maintenance. Its tough, powder-coated finish adds an extra layer of protection against rust and corrosion.

In conclusion, the Cub Cadet SLTX1054 combines power, performance, and ease of use in a single package. With features like a robust engine, expansive cutting deck, hydrostatic transmission, and advanced maneuverability, this riding mower is a fantastic choice for homeowners looking to maintain their lawns efficiently and effectively. Whether tackling large lawns or navigating tight spaces, the SLTX1054 is up to the challenge.
Top Page Image Contents