Cub Cadet 7284 Head Light Bulb Replacement, Hazard Bulb Replacement, Tail Light Bulb Replacement

Page 32

HEAD LIGHT BULB REPLACEMENT

The tractor is equipped with four headlight bulbs. If one of the bulbs should burn out, replace the bulb as follows:

Fully raise the hood so that the hood prop cylinders hold the hood in the raised position.

Pull both locking tabs of the wire harness plug away from the bulb/socket assembly and unplug the wire harness from the bulb assembly. See Figure 37.

BULB/SOCKET

ASSEMBLY.

WIRE

HARNESS REFLECTOR

PLUG

LOCKING TAB

Replace a tail light bulb as follows:

Turn the light socket counterclockwise to align the socket tabs with the notches in the tail light reflector.

Once aligned, carefully pull the light socket out of the tail light reflector.

Pull the light bulb from the socket and replace with a like part.

Align the tabs of the socket with the notches in the reflector and carefully insert the socket. Turn the socket fully clockwise to lock in place.

HAZARD BULB REPLACEMENT

Flashing hazard lights are installed on each side of the ROPS. Replace the bulbs as follows:

Grasp the outer half of the light housing and both the front and rear lenses. Accessing the screws from the notches at the top and bottom of the outer housing, remove the two screws fastening the outer and inner housings together. See Figure 38.

LENSES

Figure 37

NOTCH

SCREW

BULB SOCKET

Turn the bulb/socket assembly approximately a quarter turn counterclockwise to align its tabs with the notches of the reflector, then remove from the reflector.

Replace with a new bulb/socket assembly (Cub Cadet No. 725-3161A).

Align the tabs of the new bulb/socket assembly with the notches of the reflector and insert the bulb.

Turn the bulb/socket assembly clockwise to lock in place. Plug the wire harness into the socket, making sure the plug locking tabs lock onto the socket assembly.

NOTCH

OUTER HOUSING

INNER HOUSING

TAIL LIGHT BULB REPLACEMENT

Each tail light assembly has two light bulbs — a reverse indicator bulb (Cub Cadet no. 725-3263) and a tail light (Cub Cadet no. 725-3262). Access the back side of the tail lights from under the rear fender.

NOTE: Use caution when removing the tail light sockets from the reflector housings. The bulbs can be pulled from the sockets and dropped into the reflector housing, requiring removal of the reflector housing to retrieve the bulb.

Figure 38

Remove the outer housing and lenses.

Push in on the bulb and turn counterclockwise to remove the bulb from the light socket.

Align the new bulb with the socket slot, push the bulb into the socket, and turn clockwise to lock it in the socket.

While making certain the lenses engage the front and rear grooves of the inner housing, install the lenses and outer housing. Secure with the two screws.

32

Image 32
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualTo the Owner Table of ContentsCalling Service Information Rops Information Plate Recording Model and Serial Number InformationTractor Model Plate Important Safe Operation Practices General OperationSlope Operation ChildrenOperating the PTO Do notSafety Frame Rops ServiceStarting AID Located Under Hood Safety LabelsFAN Warning Label Located on Each Side of Radiator Roll Over Warning Label Located on RIGHT/REAR Fender Battery Warning Label Located Under HoodPTO Warning Label Located on Rear PTO Shield Controls and Features Floorboard and Dash Panel Mounted ControlsPTO Switch Ignition SwitchSeat Adjustment Lever Steering WheelHazard Light Switch Headlight SwitchDifferential Lock Pedal Parking Brake LeverBattery Indicator Light Engine Coolant Temperature LightParking Brake Indicator Light PTO Indicator LightFender Mounted Conrtols and Features PTO Reverse Override SwitchFuel Fill Cap PTO Selection LeverTransmission Hi/Lo Range Shift Lever Cup HolderHand Holds Amber Hazard LightsFolding the Rops OperationRollover Protective Structure Rops Fueling the Tractor Safety Interlock SystemNEW Tractor BREAK-IN Procedures Using Jumper Cables to Start Engine Starting the EngineCold Weather Starting Stopping the EngineUsing the FORWARD/REVERSE Pedal Driving the TractorDriving on Slopes Stopping the TractorLOW Using the HI/LO Range Shift LeverUsing the Differential Lock Pedal Engaging the PTO Using the Hydraulic Lift LeverUsing the PTO Selection Lever Using the PTO Reverse Override Switch Using the TOP Link Retainer HookHazard Lights LightingUsing the Three Point Hitch Using the Auxiliary Hydraulic ValveUsing the Hitch Plate Using the Auxiliary Hydraulic Control HandleTractor Weighting On Demand Four Wheel DriveAdjustments Adjusting the SeatAdjusting the Seat Belt Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes Adjusting Hydraulic Lift Feedback RODGeneral Information MaintenanceLubrication Table Chart Illustration Lubrication and Maintenance Chart Service Intervals Operation toAccessing the Engine Compartment General Battery InformationBattery Removal Charging the BatteryBattery Maintenance Battery StorageTail Light Bulb Replacement Head Light Bulb ReplacementHazard Bulb Replacement Accessing the Fuse Center Servicing Electrical SystemInstrument Panel Fuses RelaysHazard Light Flasher Relay Checking TRANSMISSION/HYDRAULIC System OIL LevelInitial Break-In Period Filter Change Changing TRANSMISSION/HYDRAULIC System OILRegularly Scheduled Oil Filter Changes Check Front Axle OilCheck Final Reduction Gear Case Oil Changing Front Axle and Final Reduction Gear Case OILMaintenance of the Rollover Protective Structure Rops Tire MaintenanceLubrication of Main Drive Shaft Lubrication of FWD Drive ShaftTractor Storage Removing the Tractor from StorageEngine Maintenance Cleaning the EngineCleaning RADIATOR/RADIATOR Screen Checking Engine OIL LevelAdding Engine OIL Changing the Engine OIL and FilterChecking Engine Coolant Level Changing the Engine Coolant Changing the AIR CleanerInspection of Cooling System Hoses Changing The Fuel Filter Servicing the Fuel FilterDraining The Fuel Filter Engine Breather Service Fuel Injector Nozzle ServiceSpecifications Power Take-Off General DimensionsHydraulic Lift System BrakesOptional Equipment and Accessories Description Model NumberPage Page Page CUB Cadet LLC Post Office BOX CLEVELAND, Ohio