Cub Cadet 7284 manual Hazard Light Flasher Relay, Checking TRANSMISSION/HYDRAULIC System OIL Level

Page 34

Hazard Light Flasher Relay

The flasher relay controls the on/off flashing of the hazard lights. If the hazard lights do not function properly, the flasher relay is probably faulty.

Replace the relay as follows:

•Remove the dash panel insert by removing the two screws. Refer to Figure 40.

•Pull the wire harness from the dash opening. Cut and remove the electrical tape holding the flasher relay to the harness. See Figure 43

•After first noting the position of the two harness leads, disconnect the leads and replace the faulty relay with a new relay.

•Secure the relay to the wire harness with electrical tape.

•Position the wire harness in the dash panel and reinstall the dash panel insert.

FLASHER

RELAY

TAPE

WIRE

HARNESS

HARNESS

LEADS

Figure 43

CHECKING TRANSMISSION/HYDRAULIC SYSTEM OIL LEVEL

Check the hydro transmission/hydraulic system oil level after every 50 hours of operation. Check the oil level only while the engine is stopped and the tractor is standing on a level surface.

The oil fill plug/dipstick is located at the rear of the tractor, above the rear PTO shield. See Figure 44.

•Clean the area around the oil fill plug/dipstick to prevent debris from entering the transmission housing. See Figure 44.

OIL FILL PLUG/DIPSTICK

PTO SHIELD

Full Mark

F

A

Add Mark

Figure 44

•Turn the oil fill plug/dipstick counterclockwise to unscrew from the transmission housing.

•Withdraw the dipstick and wipe it clean, then reinsert and screw in all the way. Unscrew and withdraw again to read the oil level. Always keep the oil level between the add and full marks on the dipstick (See Figure 44).

•If the oil level is low, add Cub Cadet hydraulic oil. Loosely position a funnel in the fill hole so that there is enough clearance around the fun- nel to allow the transmission to vent while the oil is poured into the transmission. Fill ONLY to the full mark, never overfill the transmission.

NOTE: Always use Cub Cadet hydraulic oil to ensure correct formulation. Substitute oils could affect performance and may cause damage to the transmission.

•Reinsert the oil fill plug/dipstick into the transmission housing and turn clockwise until tight.

34

Image 34

Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualCalling Service Information Table of ContentsTo the Owner Tractor Model Plate Recording Model and Serial Number InformationRops Information Plate Important Safe Operation Practices General OperationOperating the PTO Slope OperationChildren Do notSafety Frame Rops ServiceFAN Warning Label Located on Each Side of Radiator Safety LabelsStarting AID Located Under Hood PTO Warning Label Located on Rear PTO Shield Battery Warning Label Located Under HoodRoll Over Warning Label Located on RIGHT/REAR Fender Controls and Features Floorboard and Dash Panel Mounted ControlsSeat Adjustment Lever PTO SwitchIgnition Switch Steering WheelDifferential Lock Pedal Hazard Light SwitchHeadlight Switch Parking Brake LeverParking Brake Indicator Light Battery Indicator LightEngine Coolant Temperature Light PTO Indicator LightFuel Fill Cap Fender Mounted Conrtols and FeaturesPTO Reverse Override Switch PTO Selection LeverHand Holds Transmission Hi/Lo Range Shift LeverCup Holder Amber Hazard LightsRollover Protective Structure Rops OperationFolding the Rops NEW Tractor BREAK-IN Procedures Safety Interlock SystemFueling the Tractor Cold Weather Starting Using Jumper Cables to Start EngineStarting the Engine Stopping the EngineDriving on Slopes Using the FORWARD/REVERSE PedalDriving the Tractor Stopping the TractorUsing the Differential Lock Pedal Using the HI/LO Range Shift LeverLOW Using the PTO Selection Lever Using the Hydraulic Lift LeverEngaging the PTO Hazard Lights Using the PTO Reverse Override SwitchUsing the TOP Link Retainer Hook LightingUsing the Hitch Plate Using the Three Point HitchUsing the Auxiliary Hydraulic Valve Using the Auxiliary Hydraulic Control HandleTractor Weighting On Demand Four Wheel DriveAdjusting the Seat Belt AdjustmentsAdjusting the Seat Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes Adjusting Hydraulic Lift Feedback RODLubrication Table MaintenanceGeneral Information Chart Illustration Lubrication and Maintenance Chart Service Intervals Operation toAccessing the Engine Compartment General Battery InformationBattery Maintenance Battery RemovalCharging the Battery Battery StorageHazard Bulb Replacement Head Light Bulb ReplacementTail Light Bulb Replacement Instrument Panel Fuses Accessing the Fuse CenterServicing Electrical System RelaysHazard Light Flasher Relay Checking TRANSMISSION/HYDRAULIC System OIL LevelInitial Break-In Period Filter Change Changing TRANSMISSION/HYDRAULIC System OILRegularly Scheduled Oil Filter Changes Check Front Axle OilCheck Final Reduction Gear Case Oil Changing Front Axle and Final Reduction Gear Case OILLubrication of Main Drive Shaft Maintenance of the Rollover Protective Structure RopsTire Maintenance Lubrication of FWD Drive ShaftTractor Storage Removing the Tractor from StorageCleaning RADIATOR/RADIATOR Screen Engine MaintenanceCleaning the Engine Checking Engine OIL LevelAdding Engine OIL Changing the Engine OIL and FilterChecking Engine Coolant Level Inspection of Cooling System Hoses Changing the AIR CleanerChanging the Engine Coolant Draining The Fuel Filter Servicing the Fuel FilterChanging The Fuel Filter Engine Breather Service Fuel Injector Nozzle ServiceSpecifications Hydraulic Lift System Power Take-OffGeneral Dimensions BrakesOptional Equipment and Accessories Description Model NumberPage Page Page CUB Cadet LLC Post Office BOX CLEVELAND, Ohio