Cub Cadet 7284 manual Check Final Reduction Gear Case Oil

Page 37

Check Final Reduction Gear Case Oil

Check the oil level at the two final reduction gear case fill plugs.

Locate the fill plugs approximately midway up on the front of the right and left gear cases. See Figure 47.

Remove the fill plugs and check that the oil level is at the bottom edge of the fill port opening.

FILL PLUG

RH FINAL

REDUCTION

GEAR CASE

Figure 47

If the oil level is low, use a funnel with a flexible spout to add enough Cub Cadet Gear Lube to bring the level up to the bottom of the fill port.

Reinstall the fill plug in each gear case.

CHANGING FRONT AXLE AND FINAL REDUCTION GEAR CASE OIL

Change the front axle and final reduction gear case oil after every 300 hours of operation. The total dry capacity of both gear cases and the axle housing is approximately 82 oz. (2.5 qts.)

Change the front axle and final reduction gear case as follows:

Operate the tractor for a short period to warm the oil to the normal operating temperature. Place the tractor on a level surface, engage the parking brake, and stop the tractor engine.

To prevent debris from entering the front axle housing, clean the area around the oil fill plug/ dipstick and the axle drain plug located at the center front of the axle. Refer to Figure 46 and Figure 48.

Place a suitable container beneath the front of the axle housing.

Remove the oil fill plug/dipstick to help vent the axle, then remove the drain plug and allow the oil to drain into the container. Reinstall the drain plug after draining the oil. See Figure 48.

FRONT AXLE

 

DRAIN PLUG

 

Figure 48

Fill the axle with Cub Cadet Gear Lube until the oil level reaches the full mark on the dipstick. Do not over fill the axle housing.

Reinstall the fill plug/dipstick in the axle housing.

Move the drain pan underneath either of the final reduction gear cases.

Remove the fill plug and drain plug from the gear case and drain the oil. See Figure 49. After the oil has drained, reinstall the drain plug.

Using a funnel with a flexible spout, fill the gear case up to the bottom of the fill port with Cub Cadet Gear Lube. Reinstall the fill plug.

FILL PLUG

RH FINAL

REDUCTION

GEAR CASE

DRAIN PLUG

Figure 49

Repeat the previous three steps to change the oil in the other final reduction gear case.

Dispose of used oil in an environmentally safe manner. If necessary, contact your area EPA office for proper disposal proce- dures and recycling center locations.

37

Image 37
Contents Operator’s Manual Important Read Safety Rules and Instructions CarefullyCalling Service Information Table of ContentsTo the Owner Tractor Model Plate Recording Model and Serial Number InformationRops Information Plate General Operation Important Safe Operation PracticesChildren Slope OperationOperating the PTO Do notService Safety Frame RopsFAN Warning Label Located on Each Side of Radiator Safety LabelsStarting AID Located Under Hood PTO Warning Label Located on Rear PTO Shield Battery Warning Label Located Under HoodRoll Over Warning Label Located on RIGHT/REAR Fender Floorboard and Dash Panel Mounted Controls Controls and FeaturesIgnition Switch PTO SwitchSeat Adjustment Lever Steering WheelHeadlight Switch Hazard Light SwitchDifferential Lock Pedal Parking Brake LeverEngine Coolant Temperature Light Battery Indicator LightParking Brake Indicator Light PTO Indicator LightPTO Reverse Override Switch Fender Mounted Conrtols and FeaturesFuel Fill Cap PTO Selection LeverCup Holder Transmission Hi/Lo Range Shift LeverHand Holds Amber Hazard LightsRollover Protective Structure Rops OperationFolding the Rops NEW Tractor BREAK-IN Procedures Safety Interlock SystemFueling the Tractor Starting the Engine Using Jumper Cables to Start EngineCold Weather Starting Stopping the EngineDriving the Tractor Using the FORWARD/REVERSE PedalDriving on Slopes Stopping the TractorUsing the Differential Lock Pedal Using the HI/LO Range Shift LeverLOW Using the PTO Selection Lever Using the Hydraulic Lift LeverEngaging the PTO Using the TOP Link Retainer Hook Using the PTO Reverse Override SwitchHazard Lights LightingUsing the Auxiliary Hydraulic Valve Using the Three Point HitchUsing the Hitch Plate Using the Auxiliary Hydraulic Control HandleOn Demand Four Wheel Drive Tractor WeightingAdjusting the Seat AdjustmentsAdjusting the Seat Belt Three Point Hitch AdjustmentsCheck the TOE-IN AS Follows Adjusting Front Wheel TOE-INAdjusting Hydraulic Lift Feedback ROD Adjusting the BrakesLubrication Table MaintenanceGeneral Information Chart Illustration Service Intervals Operation to Lubrication and Maintenance ChartGeneral Battery Information Accessing the Engine CompartmentCharging the Battery Battery RemovalBattery Maintenance Battery StorageHazard Bulb Replacement Head Light Bulb ReplacementTail Light Bulb Replacement Servicing Electrical System Accessing the Fuse CenterInstrument Panel Fuses RelaysChecking TRANSMISSION/HYDRAULIC System OIL Level Hazard Light Flasher RelayChanging TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter ChangeCheck Front Axle Oil Regularly Scheduled Oil Filter ChangesChanging Front Axle and Final Reduction Gear Case OIL Check Final Reduction Gear Case OilTire Maintenance Maintenance of the Rollover Protective Structure RopsLubrication of Main Drive Shaft Lubrication of FWD Drive ShaftRemoving the Tractor from Storage Tractor StorageCleaning the Engine Engine MaintenanceCleaning RADIATOR/RADIATOR Screen Checking Engine OIL LevelChanging the Engine OIL and Filter Adding Engine OILChecking Engine Coolant Level Inspection of Cooling System Hoses Changing the AIR CleanerChanging the Engine Coolant Draining The Fuel Filter Servicing the Fuel FilterChanging The Fuel Filter Fuel Injector Nozzle Service Engine Breather ServiceSpecifications General Dimensions Power Take-OffHydraulic Lift System BrakesDescription Model Number Optional Equipment and AccessoriesPage Page Page CLEVELAND, Ohio CUB Cadet LLC Post Office BOX