Cub Cadet LTX1045 warranty Cleaning the Tractor, Air Cleaner, Spark Plug Hydrostatic Transmission

Page 20

3.Pop open the protective cap on the end of the oil drain valve to expose the drain port. See Figure 6-1

Figure 6-1

4.Remove the oil fill cap/dipstick from the oil fill tube.

5.Push the oil drain hose (packed with this manual) onto the oil drain port. Route the opposite end of the hose into an appropriate oil collection container with at least a 2.5 quart capacity, to collect the used oil.

6.The engine is equipped with either a twist-and-pull drain port or a tabbed drain port. If your engine has the twist- and-pull drain go to step a. If your engine is equipped with the tabbed drain go to step b.

a.Turn the oil drain valve 1⁄4-turn, then pull outward to begin draining oil. After the oil has finished draining, push the end of the oil drain valve back in and turn 1⁄4-turn to secure it back in place. Re-cap the end of the oil drain valve to keep debris from entering the drain port.

b.Pinch the tabs on the oil drain valve, then pull outward to begin draining oil. After the oil has finished draining, push the end of the oil drain valve back in, until the tabs click into place. Re-cap the end of the oil drain valve to keep debris from entering the drain port.

7.Replace the oil filter as instructed in the Kohler Owner’s Manual.

8.Refill the engine with new oil. Refer to the Kohler Owner’s Manual for information regarding the volume and weight of engine oil.

Air Cleaner

Service the pre-cleaner and cartridge/air cleaner element as instructed in the Engine Operator’s Manual.

Spark Plug

The spark plug should be cleaned and the gap reset once a season. Refer to the Kohler Owner’s Manual for correct plug type and gap specifications.

Hydrostatic Transmission

The hydrostatic transmission is sealed at the factory and is maintenance-free. The fluid level cannot be checked and the fluid cannot be changed.

Battery

CALIFORNIA PROPOSITION 65 WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known

to the State of California to cause cancer and reproductive harm. Wash hands after handling.

The battery is sealed and is maintenance-free. Acid levels cannot be checked and fluid can not be added.

Always keep the battery cables and terminals clean and free of corrosive build-up.

After cleaning the battery and terminals, apply a light coat of petroleum jelly or grease to both terminals.

CAUTION: If removing the battery for cleaning, disconnect the NEGATIVE (Black) wire from it’s terminal first, followed by the POSITIVE (Red) wire. When re-installing the battery, always connect the POSITIVE (Red) wire its terminal first, followed by the NEGATIVE (Black) wire. Be certain that the wires are connected to the correct terminals; reversing them could result in serious damage to your engine’s alternating system.

Cleaning the Tractor

Any fuel or oil spilled on the machine should be wiped off promptly. Do NOT allow debris to accumulate around the cooling fins of the engine, the transmission’s cooling fan or on any other part of the machine, especially the belts and pulleys.

Smart Jet

Your tractor’s deck is equipped with a water port on its surface as part of its deck wash system.

Use the Smart Jet to rinse grass clippings from the deck’s underside and prevent the buildup of corrosive chemicals. Complete the following steps AFTER EACH MOWING:

1.Drive the tractor to a level, clear spot on your lawn, near enough for your garden hose to reach.

CAUTION: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc.

1.Disengage the PTO (Blade Engage), set the parking brake and stop the engine.

2.Thread the hose coupler (packaged with your tractor’s Operator’s Manual) onto the end of your garden hose.

20

Section 6 — Maintenance & Adjustments

Image 20
Contents Operator’s Manual Table of Contents To The OwnerThank You Record Product InformationImportant Safe Operation Practices General OperationAvoid erratic operation and excessive speed Slope OperationDo Not Service General ServiceChildren TowingDo not modify engine Spark ArrestorSafety Symbols Avoid jack-knifing when towing, go slow and make wide turnsSlope Gauge TOO SteepTractor Set-Up Assembly & Set-UpContents of Crate Checking Tire Pressure Connecting the Battery CablesSetting the Deck Gauge Wheels Adjusting the Seat Gas and OilControls & Features Seat Adjustment LeverThrottle/Choke Control Choke ControlIgnition Switch Module Systems Indicator Monitor/Hour Meter LCDDeck Lift Lever Drive PedalParking Brake/Cruise Control Lever Fuel Level IndicatorPTO/Blade Engage Handle Safety Interlock Switches OperationStarting the Engine Stopping the EngineReverse Caution Mode Driving The TractorEngaging the Parking Brake Setting the Cruise Control Using the Deck Lift LeverDriving On Slopes Operating the HeadlightsEngaging the PTO MowingMaintenance & Adjustments Maintenance ScheduleMaintenance Changing the Engine OilCleaning the Tractor Air CleanerSpark Plug Hydrostatic Transmission Smart JetLubrication Front WheelsPivot Points & Linkage Deck WheelsAdjustments Parking Brake AdjustmentHex Bolt Adjustment Gear Leveling the Deck Front To RearSteering Adjustment Off-Season StorageBall Joint Drag Link Hex Nut Before storing the machine for an extended periodDeck Idler Bracket ServiceCutting Deck Removal Changing the Deck Belt Deck Lift Arm Deck Support PinReplace the belt guard. See Figure Cutting BladesPulley Battery Jump StartingFuse TiresChanging the Transmission Drive Belt ChargingTroubleshooting Problem Cause RemedyKM-11013-7050 Component Part Number and DescriptionSpark Plug BPR4ES NGK Kawasaki Choke Control Cable Kawasaki Twin Fuel Tank Cap Kaw. & Kohl. Twin CylThrottle Control Cable Kawasaki Twin Attachments & Accessories Model Number DescriptionYour Warranty Rights and Obligations Warranted Parts GDOC-100223 Rev. aGDOC-100014 REV. B CanadaManual del Operador Al propietario GraciasÍndice Registro de información de productoMedidas importantes de seguridad Funcionamiento generalNo haga lo siguiente Funcionamiento en pendientesHaga lo siguiente Servicio NiñosRemolque Manejo seguro de la gasolinaGuardachispas No modifique el motorAviso referido a emisiones Evite navaja al remolcar. Vaya lento y haga vueltas anchas Símbolos De SeguridadGuarde manos y pies lejos de hacer girar partes Aceptar Montaje y Configuración Configuración del tractorContenido del cajón Mover Manualmente el TractorAjuste de las ruedas de calibración de la plataforma Instalación del cable de la bateríasControl de la presión de los neumáticos Ajuste del asiento Gasolina y aceiteControles y Características Control del regulador/cebadorPedal de freno Palanca de ajuste del asientoPedal de la transmisión Pedal de la marcha atrásMódulo del interruptor de encendido FrenoCargo Neto Indicador de nivel de combustibleControl del Estrangulador AceiteFuncionamiento Encendido del motorDetención del motor Enganche de cuchilla esté en posición desconectada OFFBotón de Conducción del tractorModo de precaución en marcha atrás Activación del control de crucero Operación en pendientesColocación del freno de mano PTO enganche de cuchilla hasta la posición on Conectada Utilización de la palanca de elevación de la plataformaCorte de césped Mantenimiento y Ajustes Calendario de mantenimientoMantenimiento MotorLimpieza del tractor Depurador de aireBujía de encendido Palanca de cambioLubricación Ruedas delanterasPuntos de pivote y varillaje Ruedas de plataformaAjustes Nivelación de la plataforma adelante atrásNivelación de la plataforma lado a lado Perno Hexagonal Engranaje de AjusteAlmacenamiento fuera de temporada Ajuste del freno de manoAjuste del volante Rótula Barra de Acoplamiento Tuerca hexagonalSoporte De la Cubierta Polea ServicioExtracción de la plataforma de corte Cuchillas de corte Para retirar las cuchillas, haga lo siguienteBorde desgastado De cuchilla Ventilete Afilado FiguraBatería FusibleArranque por medio de conexión en puente Carga de la bateríaCambio de la correa de la plataforma NeumáticosCambio de la correa de transmisión Replace the belt guard. See Figura Solución de Problemas Angosta Afile o cambie la cuchillaCorte desigual La plataforma no está correctamente Nivelada Afile o cambie la cuchillaPiezas de reemplazo Componente Número de pieza y DescripciónTapa del Tanque de Combustible Control del Acelerador Kawasaki DobleAditamentos y Accesorios Máquina Quitanieve Archivo adjuntoSUS Derechos Y Obligaciones EN Cuanto a LA Garantía Modificada GDOC-100223En Estados Unidos de América En Canadá

LTX1045, LTX1042KW, LTX1046M specifications

Cub Cadet is a well-known name in the lawn care industry, renowned for producing high-quality riding mowers. Among their popular models are the Cub Cadet LTX1046M, LTX1042KW, and LTX1045, each designed to deliver exceptional performance and ease of use.

The Cub Cadet LTX1046M features a robust 19.5 HP Kohler engine, providing ample power for tackling large lawns. Its 46-inch deck allows for efficient cutting while reducing mowing time. The LTX1046M also includes a hydrostatic transmission, which offers seamless speed adjustments, making it easier to navigate various terrains. The Comfort Glide front axle enhances maneuverability and reduces the impact of uneven ground, ensuring a smoother mowing experience.

On the other hand, the LTX1042KW is equipped with a reliable 18 HP Kawasaki engine, emphasizing performance and fuel efficiency. This model boasts a compact 42-inch mowing deck, allowing it to navigate tighter spaces while still delivering a clean cut. The LTX1042KW features a dual blade cutting system, providing superior grass clipping distribution and reducing the likelihood of clumping. Additionally, its Ergonomic steering wheel ensures comfort during prolonged usage.

Meanwhile, the LTX1045 provides an excellent balance of power and versatility with a 22 HP Kohler engine. Its 45-inch deck offers flexibility in handling larger areas while still being efficient around obstacles. This model is designed with a premium seat featuring high back support, allowing users to mow comfortably for extended periods. The LTX1045 also includes an optional bagging attachment, making it ideal for users who prefer to collect clippings for a tidier lawn.

All three models feature Cub Cadet's signature Cut Model technology, which enhances cutting performance and ensures a clean finish. The Easy Clean Deck design makes maintenance simpler, allowing users to wash the deck without heavy lifting. Additionally, the intuitive control panel across all three mowers provides users with easy access to essential functions, including blade engagement and ignition.

In summary, whether you choose the LTX1046M, LTX1042KW, or LTX1045, each model offers unique features and reliable performance, making them excellent choices for lawn care enthusiasts. These riding mowers combine power, comfort, and advanced technology to ensure that your lawn always looks its best.