Cub Cadet LTX1046M, LTX1042KW, LTX1045 warranty Service, Cutting Deck Removal, Deck Idler Bracket

Page 24

Service

Cutting Deck Removal

1.Place the PTO/Blade Engage lever in the disengaged (OFF) position and engage the parking brake.

2.Lower the deck by moving the deck lift lever into the bottom notch on the right fender.

3.Locate the engine pulley under the front of your tractor. See Figure 7-1.

Figure 7-1

4.Remove the belt guard and belt as follows. Refer to Figure

7-1:

a.Remove the hex screws.

b.Pull the belt keeper rod to the right and down to remove.

c.Remove the deck belt from around the tractor’s engine pulley.

7

NOTE: If there is too much tension on the belt for it to be easily removed from the engine pulley, carefully insert a 3⁄8” drive ratchet wrench (set to loosen) into the square hole found in the deck idler bracket and pivot it toward the tractor’s left side to relieve tension on the belt. See Figure 7-2.

Deck Idler

Bracket

Figure 7-2

WARNING! Avoid pinching injuries. Never place your fingers on the idler spring or between the belt and a pulley while removing the belt.

5.Looking at the cutting deck from the left side of the tractor, locate the deck support pin on the rear left side of the deck.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Operator’s Manual Table of Contents To The OwnerThank You Record Product InformationImportant Safe Operation Practices General OperationSlope Operation Do NotAvoid erratic operation and excessive speed Service General ServiceChildren TowingDo not modify engine Spark ArrestorSafety Symbols Avoid jack-knifing when towing, go slow and make wide turnsSlope Gauge TOO SteepAssembly & Set-Up Contents of CrateTractor Set-Up Connecting the Battery Cables Setting the Deck Gauge WheelsChecking Tire Pressure Adjusting the Seat Gas and OilControls & Features Seat Adjustment LeverThrottle/Choke Control Choke ControlIgnition Switch Module Systems Indicator Monitor/Hour Meter LCDDeck Lift Lever Drive PedalFuel Level Indicator PTO/Blade Engage HandleParking Brake/Cruise Control Lever Safety Interlock Switches OperationStarting the Engine Stopping the EngineReverse Caution Mode Driving The TractorEngaging the Parking Brake Setting the Cruise Control Using the Deck Lift LeverDriving On Slopes Operating the HeadlightsEngaging the PTO MowingMaintenance & Adjustments Maintenance ScheduleMaintenance Changing the Engine OilCleaning the Tractor Air CleanerSpark Plug Hydrostatic Transmission Smart JetLubrication Front WheelsPivot Points & Linkage Deck WheelsAdjustments Parking Brake AdjustmentHex Bolt Adjustment Gear Leveling the Deck Front To RearSteering Adjustment Off-Season StorageBall Joint Drag Link Hex Nut Before storing the machine for an extended periodService Cutting Deck RemovalDeck Idler Bracket Changing the Deck Belt Deck Lift Arm Deck Support PinCutting Blades PulleyReplace the belt guard. See Figure Battery Jump StartingFuse TiresChanging the Transmission Drive Belt ChargingTroubleshooting Problem Cause RemedyComponent Part Number and Description Spark Plug BPR4ES NGK KawasakiKM-11013-7050 Fuel Tank Cap Kaw. & Kohl. Twin Cyl Throttle Control Cable Kawasaki TwinChoke Control Cable Kawasaki Twin Attachments & Accessories Model Number DescriptionYour Warranty Rights and Obligations Warranted Parts GDOC-100223 Rev. aGDOC-100014 REV. B CanadaManual del Operador Al propietario GraciasÍndice Registro de información de productoMedidas importantes de seguridad Funcionamiento generalFuncionamiento en pendientes Haga lo siguienteNo haga lo siguiente Servicio NiñosRemolque Manejo seguro de la gasolinaNo modifique el motor Aviso referido a emisionesGuardachispas Símbolos De Seguridad Guarde manos y pies lejos de hacer girar partesEvite navaja al remolcar. Vaya lento y haga vueltas anchas Aceptar Montaje y Configuración Configuración del tractorContenido del cajón Mover Manualmente el TractorInstalación del cable de la baterías Control de la presión de los neumáticosAjuste de las ruedas de calibración de la plataforma Ajuste del asiento Gasolina y aceiteControles y Características Control del regulador/cebadorPedal de freno Palanca de ajuste del asientoPedal de la transmisión Pedal de la marcha atrásMódulo del interruptor de encendido FrenoCargo Neto Indicador de nivel de combustibleControl del Estrangulador AceiteFuncionamiento Encendido del motorDetención del motor Enganche de cuchilla esté en posición desconectada OFFConducción del tractor Modo de precaución en marcha atrásBotón de Operación en pendientes Colocación del freno de manoActivación del control de crucero Utilización de la palanca de elevación de la plataforma Corte de céspedPTO enganche de cuchilla hasta la posición on Conectada Mantenimiento y Ajustes Calendario de mantenimientoMantenimiento MotorLimpieza del tractor Depurador de aireBujía de encendido Palanca de cambioLubricación Ruedas delanterasPuntos de pivote y varillaje Ruedas de plataformaAjustes Nivelación de la plataforma adelante atrásNivelación de la plataforma lado a lado Perno Hexagonal Engranaje de AjusteAlmacenamiento fuera de temporada Ajuste del freno de manoAjuste del volante Rótula Barra de Acoplamiento Tuerca hexagonalServicio Extracción de la plataforma de corteSoporte De la Cubierta Polea Cuchillas de corte Para retirar las cuchillas, haga lo siguienteBorde desgastado De cuchilla Ventilete Afilado FiguraBatería FusibleArranque por medio de conexión en puente Carga de la bateríaNeumáticos Cambio de la correa de transmisiónCambio de la correa de la plataforma Replace the belt guard. See Figura Solución de Problemas Angosta Afile o cambie la cuchillaCorte desigual La plataforma no está correctamente Nivelada Afile o cambie la cuchillaPiezas de reemplazo Componente Número de pieza y DescripciónTapa del Tanque de Combustible Control del Acelerador Kawasaki DobleAditamentos y Accesorios Máquina Quitanieve Archivo adjuntoSUS Derechos Y Obligaciones EN Cuanto a LA Garantía Modificada GDOC-100223En Estados Unidos de América En Canadá

LTX1045, LTX1042KW, LTX1046M specifications

Cub Cadet is a well-known name in the lawn care industry, renowned for producing high-quality riding mowers. Among their popular models are the Cub Cadet LTX1046M, LTX1042KW, and LTX1045, each designed to deliver exceptional performance and ease of use.

The Cub Cadet LTX1046M features a robust 19.5 HP Kohler engine, providing ample power for tackling large lawns. Its 46-inch deck allows for efficient cutting while reducing mowing time. The LTX1046M also includes a hydrostatic transmission, which offers seamless speed adjustments, making it easier to navigate various terrains. The Comfort Glide front axle enhances maneuverability and reduces the impact of uneven ground, ensuring a smoother mowing experience.

On the other hand, the LTX1042KW is equipped with a reliable 18 HP Kawasaki engine, emphasizing performance and fuel efficiency. This model boasts a compact 42-inch mowing deck, allowing it to navigate tighter spaces while still delivering a clean cut. The LTX1042KW features a dual blade cutting system, providing superior grass clipping distribution and reducing the likelihood of clumping. Additionally, its Ergonomic steering wheel ensures comfort during prolonged usage.

Meanwhile, the LTX1045 provides an excellent balance of power and versatility with a 22 HP Kohler engine. Its 45-inch deck offers flexibility in handling larger areas while still being efficient around obstacles. This model is designed with a premium seat featuring high back support, allowing users to mow comfortably for extended periods. The LTX1045 also includes an optional bagging attachment, making it ideal for users who prefer to collect clippings for a tidier lawn.

All three models feature Cub Cadet's signature Cut Model technology, which enhances cutting performance and ensures a clean finish. The Easy Clean Deck design makes maintenance simpler, allowing users to wash the deck without heavy lifting. Additionally, the intuitive control panel across all three mowers provides users with easy access to essential functions, including blade engagement and ignition.

In summary, whether you choose the LTX1046M, LTX1042KW, or LTX1045, each model offers unique features and reliable performance, making them excellent choices for lawn care enthusiasts. These riding mowers combine power, comfort, and advanced technology to ensure that your lawn always looks its best.
Top Page Image Contents