Cub Cadet LTX1046M, LTX1042KW, LTX1045 warranty Battery, Jump Starting

Page 27

Figure 7-9

4.To properly sharpen the cutting blades, remove equal amounts of metal from both ends of the blades along the cutting edges, parallel to the trailing edge, at a 25°- 30° angle. Always grind each cutting blade edge equally to maintain proper blade balance. See Figure 7-10.

CAUTION: If the cutting edge of the blade has previously been sharpened, or if any metal separation is present, replace the blades with new ones.

WARNING! A poorly balanced blade will cause excessive vibration, may cause damage to the tractor and/or result in personal injury.

Figure 7-10

5.Test the blade’s balance using a blade balancer. Grind metal from the heavy side until it balances evenly.

NOTE: When replacing the blade, be sure to install the blade with the side of the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the ground when the mower is in the operating position.

CAUTION: Use a torque wrench to tighten the blade spindle hex flange nut to between 70 ft-lbs and 90 ft-lbs.

Battery

CALIFORNIA PROPOSITION 65 WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

CAUTION: If removing the battery, disconnect the NEGATIVE (Black) wire from its terminal first, followed by the POSITIVE (Red) wire. When reinstalling the battery, always connect the POSITIVE (Red) wire its terminal first, followed by the NEGATIVE (Black) wire.

Jump Starting

WARNING! Never jump start a damaged or frozen battery. Be certain the vehicles do not touch and ignitions are off. Do not allow cable clamps to touch.

1.Connect the positive (+) cable to positive (+) post of your tractor’s discharged battery.

2.Connect the other end of the cable to the positive (+) post of the jumper battery.

3.Connect the negative () cable to the other post of the jumper battery.

4.Make the final connection on the engine block of the tractor, away from the battery. Attach to an unpainted part to assure a good connection.

CAUTION: If the jumper battery is installed on a vehicle (i.e. car, truck), do NOT start the vehicle’s engine when jump starting your tractor.

5.Start the tractor (as instructed in the Operation section of this manual).

6.Set the tractor’s parking brake before removing the jumper cables, in reverse order of connection.

Section 7 — Service

27

Image 27
Contents Operator’s Manual Record Product Information Table of ContentsTo The Owner Thank YouGeneral Operation Important Safe Operation PracticesSlope Operation Do NotAvoid erratic operation and excessive speed Towing ServiceGeneral Service ChildrenSpark Arrestor Do not modify engineAvoid jack-knifing when towing, go slow and make wide turns Safety SymbolsTOO Steep Slope GaugeAssembly & Set-Up Contents of CrateTractor Set-Up Connecting the Battery Cables Setting the Deck Gauge WheelsChecking Tire Pressure Gas and Oil Adjusting the SeatChoke Control Controls & FeaturesSeat Adjustment Lever Throttle/Choke ControlDrive Pedal Ignition Switch ModuleSystems Indicator Monitor/Hour Meter LCD Deck Lift LeverFuel Level Indicator PTO/Blade Engage HandleParking Brake/Cruise Control Lever Stopping the Engine Safety Interlock SwitchesOperation Starting the EngineDriving The Tractor Reverse Caution ModeOperating the Headlights Engaging the Parking Brake Setting the Cruise ControlUsing the Deck Lift Lever Driving On SlopesMowing Engaging the PTOChanging the Engine Oil Maintenance & AdjustmentsMaintenance Schedule MaintenanceSmart Jet Cleaning the TractorAir Cleaner Spark Plug Hydrostatic TransmissionDeck Wheels LubricationFront Wheels Pivot Points & LinkageLeveling the Deck Front To Rear AdjustmentsParking Brake Adjustment Hex Bolt Adjustment GearBefore storing the machine for an extended period Steering AdjustmentOff-Season Storage Ball Joint Drag Link Hex NutService Cutting Deck RemovalDeck Idler Bracket Deck Lift Arm Deck Support Pin Changing the Deck BeltCutting Blades PulleyReplace the belt guard. See Figure Jump Starting BatteryCharging FuseTires Changing the Transmission Drive BeltProblem Cause Remedy TroubleshootingComponent Part Number and Description Spark Plug BPR4ES NGK KawasakiKM-11013-7050 Fuel Tank Cap Kaw. & Kohl. Twin Cyl Throttle Control Cable Kawasaki TwinChoke Control Cable Kawasaki Twin Model Number Description Attachments & AccessoriesYour Warranty Rights and Obligations GDOC-100223 Rev. a Warranted PartsCanada GDOC-100014 REV. BManual del Operador Registro de información de producto Al propietarioGracias ÍndiceFuncionamiento general Medidas importantes de seguridadFuncionamiento en pendientes Haga lo siguienteNo haga lo siguiente Manejo seguro de la gasolina ServicioNiños RemolqueNo modifique el motor Aviso referido a emisionesGuardachispas Símbolos De Seguridad Guarde manos y pies lejos de hacer girar partesEvite navaja al remolcar. Vaya lento y haga vueltas anchas Aceptar Mover Manualmente el Tractor Montaje y ConfiguraciónConfiguración del tractor Contenido del cajónInstalación del cable de la baterías Control de la presión de los neumáticosAjuste de las ruedas de calibración de la plataforma Gasolina y aceite Ajuste del asientoPalanca de ajuste del asiento Controles y CaracterísticasControl del regulador/cebador Pedal de frenoFreno Pedal de la transmisiónPedal de la marcha atrás Módulo del interruptor de encendidoAceite Cargo NetoIndicador de nivel de combustible Control del EstranguladorEnganche de cuchilla esté en posición desconectada OFF FuncionamientoEncendido del motor Detención del motorConducción del tractor Modo de precaución en marcha atrásBotón de Operación en pendientes Colocación del freno de manoActivación del control de crucero Utilización de la palanca de elevación de la plataforma Corte de céspedPTO enganche de cuchilla hasta la posición on Conectada Motor Mantenimiento y AjustesCalendario de mantenimiento MantenimientoPalanca de cambio Limpieza del tractorDepurador de aire Bujía de encendidoRuedas de plataforma LubricaciónRuedas delanteras Puntos de pivote y varillajePerno Hexagonal Engranaje de Ajuste AjustesNivelación de la plataforma adelante atrás Nivelación de la plataforma lado a ladoRótula Barra de Acoplamiento Tuerca hexagonal Almacenamiento fuera de temporadaAjuste del freno de mano Ajuste del volanteServicio Extracción de la plataforma de corteSoporte De la Cubierta Polea Para retirar las cuchillas, haga lo siguiente Cuchillas de corteFigura Borde desgastado De cuchilla Ventilete AfiladoCarga de la batería BateríaFusible Arranque por medio de conexión en puenteNeumáticos Cambio de la correa de transmisiónCambio de la correa de la plataforma Replace the belt guard. See Figura Solución de Problemas Nivelada Afile o cambie la cuchilla AngostaAfile o cambie la cuchilla Corte desigual La plataforma no está correctamenteComponente Número de pieza y Descripción Piezas de reemplazoControl del Acelerador Kawasaki Doble Tapa del Tanque de CombustibleMáquina Quitanieve Archivo adjunto Aditamentos y AccesoriosSUS Derechos Y Obligaciones EN Cuanto a LA Garantía GDOC-100223 ModificadaEn Estados Unidos de América En Canadá

LTX1045, LTX1042KW, LTX1046M specifications

Cub Cadet is a well-known name in the lawn care industry, renowned for producing high-quality riding mowers. Among their popular models are the Cub Cadet LTX1046M, LTX1042KW, and LTX1045, each designed to deliver exceptional performance and ease of use.

The Cub Cadet LTX1046M features a robust 19.5 HP Kohler engine, providing ample power for tackling large lawns. Its 46-inch deck allows for efficient cutting while reducing mowing time. The LTX1046M also includes a hydrostatic transmission, which offers seamless speed adjustments, making it easier to navigate various terrains. The Comfort Glide front axle enhances maneuverability and reduces the impact of uneven ground, ensuring a smoother mowing experience.

On the other hand, the LTX1042KW is equipped with a reliable 18 HP Kawasaki engine, emphasizing performance and fuel efficiency. This model boasts a compact 42-inch mowing deck, allowing it to navigate tighter spaces while still delivering a clean cut. The LTX1042KW features a dual blade cutting system, providing superior grass clipping distribution and reducing the likelihood of clumping. Additionally, its Ergonomic steering wheel ensures comfort during prolonged usage.

Meanwhile, the LTX1045 provides an excellent balance of power and versatility with a 22 HP Kohler engine. Its 45-inch deck offers flexibility in handling larger areas while still being efficient around obstacles. This model is designed with a premium seat featuring high back support, allowing users to mow comfortably for extended periods. The LTX1045 also includes an optional bagging attachment, making it ideal for users who prefer to collect clippings for a tidier lawn.

All three models feature Cub Cadet's signature Cut Model technology, which enhances cutting performance and ensures a clean finish. The Easy Clean Deck design makes maintenance simpler, allowing users to wash the deck without heavy lifting. Additionally, the intuitive control panel across all three mowers provides users with easy access to essential functions, including blade engagement and ignition.

In summary, whether you choose the LTX1046M, LTX1042KW, or LTX1045, each model offers unique features and reliable performance, making them excellent choices for lawn care enthusiasts. These riding mowers combine power, comfort, and advanced technology to ensure that your lawn always looks its best.