Cub Cadet LTX1045, LTX1046M, LTX1042KW warranty Adjusting the Seat, Gas and Oil

Page 11

Adjusting the Seat

To adjust the position of the seat, pull up and hold the seat adjustment lever. Slide the seat forward or rearward to the desired position; then release the adjustment lever. Make sure seat is locked into position before operating the tractor. See Figure 3-5.

Figure 3-5

WARNING! Before operating the tractor, make sure the seat is engaged in the seat-stop. Engage the parking brake. Stand behind the machine and pull back on seat until it clicks into place.

Gas and Oil

The fuel tank is located under the hood. Remove the fuel cap by turning it counterclockwise. Use only clean, fresh (no more than 30 days old), unleaded gasoline. Do not overfill the tank.

The tractor is equipped with a tethered, ratcheting cap, STOP filling tank once fuel is seen inside the filler neck. This ensures that a proper expansion volume is created. Do NOT top off tank.

See Figure 3-6.

Figure 3-6

WARNING! Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine

indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

NOTE: Your tractor is shipped with oil in the engine. However, you MUST check the oil level before operating.

CAUTION: Always check the engine oil level before each use as instructed in the separate Engine Owner’s Manual. Add oil as necessary. Failure to do so may result in serious damage to your engine.

Section 3 — Assembly & Set-Up

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Operator’s Manual Record Product Information Table of ContentsTo The Owner Thank YouGeneral Operation Important Safe Operation PracticesAvoid erratic operation and excessive speed Slope OperationDo Not Towing ServiceGeneral Service ChildrenSpark Arrestor Do not modify engineAvoid jack-knifing when towing, go slow and make wide turns Safety SymbolsTOO Steep Slope GaugeTractor Set-Up Assembly & Set-UpContents of Crate Checking Tire Pressure Connecting the Battery CablesSetting the Deck Gauge Wheels Gas and Oil Adjusting the SeatChoke Control Controls & FeaturesSeat Adjustment Lever Throttle/Choke ControlDrive Pedal Ignition Switch ModuleSystems Indicator Monitor/Hour Meter LCD Deck Lift LeverParking Brake/Cruise Control Lever Fuel Level IndicatorPTO/Blade Engage Handle Stopping the Engine Safety Interlock SwitchesOperation Starting the EngineDriving The Tractor Reverse Caution ModeOperating the Headlights Engaging the Parking Brake Setting the Cruise ControlUsing the Deck Lift Lever Driving On SlopesMowing Engaging the PTOChanging the Engine Oil Maintenance & AdjustmentsMaintenance Schedule MaintenanceSmart Jet Cleaning the TractorAir Cleaner Spark Plug Hydrostatic TransmissionDeck Wheels LubricationFront Wheels Pivot Points & LinkageLeveling the Deck Front To Rear AdjustmentsParking Brake Adjustment Hex Bolt Adjustment GearBefore storing the machine for an extended period Steering AdjustmentOff-Season Storage Ball Joint Drag Link Hex NutDeck Idler Bracket ServiceCutting Deck Removal Deck Lift Arm Deck Support Pin Changing the Deck BeltReplace the belt guard. See Figure Cutting BladesPulley Jump Starting BatteryCharging FuseTires Changing the Transmission Drive BeltProblem Cause Remedy TroubleshootingKM-11013-7050 Component Part Number and DescriptionSpark Plug BPR4ES NGK Kawasaki Choke Control Cable Kawasaki Twin Fuel Tank Cap Kaw. & Kohl. Twin CylThrottle Control Cable Kawasaki Twin Model Number Description Attachments & AccessoriesYour Warranty Rights and Obligations GDOC-100223 Rev. a Warranted PartsCanada GDOC-100014 REV. BManual del Operador Registro de información de producto Al propietarioGracias ÍndiceFuncionamiento general Medidas importantes de seguridadNo haga lo siguiente Funcionamiento en pendientesHaga lo siguiente Manejo seguro de la gasolina ServicioNiños RemolqueGuardachispas No modifique el motorAviso referido a emisiones Evite navaja al remolcar. Vaya lento y haga vueltas anchas Símbolos De SeguridadGuarde manos y pies lejos de hacer girar partes Aceptar Mover Manualmente el Tractor Montaje y ConfiguraciónConfiguración del tractor Contenido del cajónAjuste de las ruedas de calibración de la plataforma Instalación del cable de la bateríasControl de la presión de los neumáticos Gasolina y aceite Ajuste del asientoPalanca de ajuste del asiento Controles y CaracterísticasControl del regulador/cebador Pedal de frenoFreno Pedal de la transmisiónPedal de la marcha atrás Módulo del interruptor de encendidoAceite Cargo NetoIndicador de nivel de combustible Control del EstranguladorEnganche de cuchilla esté en posición desconectada OFF FuncionamientoEncendido del motor Detención del motorBotón de Conducción del tractorModo de precaución en marcha atrás Activación del control de crucero Operación en pendientesColocación del freno de mano PTO enganche de cuchilla hasta la posición on Conectada Utilización de la palanca de elevación de la plataformaCorte de césped Motor Mantenimiento y AjustesCalendario de mantenimiento MantenimientoPalanca de cambio Limpieza del tractorDepurador de aire Bujía de encendidoRuedas de plataforma LubricaciónRuedas delanteras Puntos de pivote y varillajePerno Hexagonal Engranaje de Ajuste AjustesNivelación de la plataforma adelante atrás Nivelación de la plataforma lado a ladoRótula Barra de Acoplamiento Tuerca hexagonal Almacenamiento fuera de temporadaAjuste del freno de mano Ajuste del volanteSoporte De la Cubierta Polea ServicioExtracción de la plataforma de corte Para retirar las cuchillas, haga lo siguiente Cuchillas de corteFigura Borde desgastado De cuchilla Ventilete AfiladoCarga de la batería BateríaFusible Arranque por medio de conexión en puenteCambio de la correa de la plataforma NeumáticosCambio de la correa de transmisión Replace the belt guard. See Figura Solución de Problemas Nivelada Afile o cambie la cuchilla AngostaAfile o cambie la cuchilla Corte desigual La plataforma no está correctamenteComponente Número de pieza y Descripción Piezas de reemplazoControl del Acelerador Kawasaki Doble Tapa del Tanque de CombustibleMáquina Quitanieve Archivo adjunto Aditamentos y AccesoriosSUS Derechos Y Obligaciones EN Cuanto a LA Garantía GDOC-100223 ModificadaEn Estados Unidos de América En Canadá

LTX1045, LTX1042KW, LTX1046M specifications

Cub Cadet is a well-known name in the lawn care industry, renowned for producing high-quality riding mowers. Among their popular models are the Cub Cadet LTX1046M, LTX1042KW, and LTX1045, each designed to deliver exceptional performance and ease of use.

The Cub Cadet LTX1046M features a robust 19.5 HP Kohler engine, providing ample power for tackling large lawns. Its 46-inch deck allows for efficient cutting while reducing mowing time. The LTX1046M also includes a hydrostatic transmission, which offers seamless speed adjustments, making it easier to navigate various terrains. The Comfort Glide front axle enhances maneuverability and reduces the impact of uneven ground, ensuring a smoother mowing experience.

On the other hand, the LTX1042KW is equipped with a reliable 18 HP Kawasaki engine, emphasizing performance and fuel efficiency. This model boasts a compact 42-inch mowing deck, allowing it to navigate tighter spaces while still delivering a clean cut. The LTX1042KW features a dual blade cutting system, providing superior grass clipping distribution and reducing the likelihood of clumping. Additionally, its Ergonomic steering wheel ensures comfort during prolonged usage.

Meanwhile, the LTX1045 provides an excellent balance of power and versatility with a 22 HP Kohler engine. Its 45-inch deck offers flexibility in handling larger areas while still being efficient around obstacles. This model is designed with a premium seat featuring high back support, allowing users to mow comfortably for extended periods. The LTX1045 also includes an optional bagging attachment, making it ideal for users who prefer to collect clippings for a tidier lawn.

All three models feature Cub Cadet's signature Cut Model technology, which enhances cutting performance and ensures a clean finish. The Easy Clean Deck design makes maintenance simpler, allowing users to wash the deck without heavy lifting. Additionally, the intuitive control panel across all three mowers provides users with easy access to essential functions, including blade engagement and ignition.

In summary, whether you choose the LTX1046M, LTX1042KW, or LTX1045, each model offers unique features and reliable performance, making them excellent choices for lawn care enthusiasts. These riding mowers combine power, comfort, and advanced technology to ensure that your lawn always looks its best.
Top Page Image Contents