6.2Adjusting the detergent pressure
Set the adjustable nozzle on " 
" to deliver detergent at the correct pressure (on models with this feature).
6.3Adjusting the pressure
The regulator (G) is used to adjust the working pressure. The pres- sure is shown on the pressure gauge (where fitted).
7INFORMATION ON USE OF THE APPLIANCE (FIG.4)
7.1Operating in high pressure mode
Unwind the high pressure hose to the required length. Hold the gun open for a few seconds.
Turn the master switch (FIG.4 Ref. H) to (I) (On).
Set the nozzle (FIG. 1 Ref. B1) in high pressure mode (fully back (FIG.3, "
"position).
Press the trigger of the gun (FIG.4 Ref.I) to obtain a jet of water. Adjust the type of jet by turning the nozzle (FIG. 3 Ref. E).
To stop operation of the appliance, release the trigger (FIG.4 Ref.I). The appliance is fitted with a pressure switch.
The motor does not start unless the trigger of the gun (FIG.4 Ref. I) is pressed.
Caution - Danger!
During operation the appliance must be positioned as shown in FIG. 4 on a sturdy, stable surface.
Caution - Danger!
Do not obstruct the appliance’s cooling vents during operation.
To allow the TSS device to function correctly, do not operate the trigger (pressing or releasing) at intervals of less than
If the appliance is to be out of use for more than 10 min., it should always be switched off using the
7.2Operating in low pressure mode and with detergent Unwind the high pressure hose to the required length.
When using detergent, the adjustable nozzle must be set on "
". Set the nozzle (FIG. 1 Ref. B1) in low pressure mode (fully forward (FIG.3).
Press the trigger of the gun (FIG.4 Ref.I) to obtain a jet of water. Hold the gun open for a few seconds.
Turn the master switch (FIG.4 Ref. H) to (I) (On).
To stop operation of the appliance, release the trigger (FIG.4 Ref.I). The motor does not start unless the trigger of the gun (FIG.4 Ref. I) is pressed.
Caution - Danger!
During operation the appliance must be positioned as shown in FIG. 4 on a sturdy, stable surface.
7.2.1Adjusting the detergent
Detergent flow is adjusted using the regulator (F).
7.3Stopping the appliance
1) Set the starter device switch off (OFF/0).
2) Depress the gun trigger and discharge the residual pressure inside the hoses.
3) Engage the gun safety catch (D).
7.4Restarting
1) Release the safety catch (D).
2) Depress the gun trigger and discharge the residual air inside the hoses.
3) Set the starter device on (ON/1).
ENGLISH
7.5Storage
1)Switch the appliance off (OFF/0).
2)Remove the plug from the socket.
3)Turn off the water supply tap.
4)Discharge the residual pressure from the gun until all the water has come out of the nozzle.
5)Drain the detergent tank.
6)Engage the gun safety catch (D).
7.6Recommended cleaning procedure
Dissolve dirt by applying the detergent mixed with water to the surface while still dry.
When dealing with vertical surfaces work from the bottom upwards.
Leave the detergent to act for
8MAINTENANCE (FIG.5)
Any maintenance operations not covered by this chapter should be carried out by an Authorized Sales and Service Centre.
Caution - Danger!
Always disconnect the plug from the power socket before carrying out any work on the appliance.
8.1Cleaning the nozzle
1) Disconnect the lance from the nozzle.
2) Remove any dirt deposits from the nozzle hole using the tool (C1).
8.2Cleaning the filter
Clean the inlet filter (L) every time before using the unit. Please read the Cleaning the Water Inlet Filter section.
8.3End-of-season storage
Treat the appliance with
17