Black & Decker PW2100 General Information, Technical Information, Electrical Connection

ENGLISH

3GENERAL INFORMATION (FIG.1)

3.1Use of the manual

This manual forms an integral part of the appliance and should be kept for future reference. Please read it carefully before installing/ using the unit. If the appliance is sold, the Seller must pass on this manual to the new owner along with the appliance.

3.2Delivery

The appliance is delivered partially assembled in a cardboard box. The supply package is illustrated in FIG.1.

3.2.1Documentation supplied with the appliance A1 Use and maintenance manual

3.3Disposing of packaging

The packaging materials are not environmental pollutants but must still be recycled or disposed of in compliance with the relevant legislation in the country of use.

3.4Safety signs

Comply with the instructions provided by the safety signs fitted to the appliance.

Check that they are present and legible; otherwise, fit replacements in the original positions.

4TECHNICAL INFORMATION (FIG.1)

4.1Envisaged use

This appliance has been designed for individual use for the cleaning of vehicles, machines, boats, masonry, etc, to remove stubborn dirt using clean water and biodegradable chemical detergents.

Vehicle engines may be washed only if the dirty water is disposed of as per regulations in force.

-  Intake water temperature: see data plate on the appliance.

-  Intake water pressure: below 10 bar.

-  Operating ambient temperature above 0°C.

4.2Operator

The symbol on the front cover identifies the appliance’s intended operator (professional or non-professional).

4.3Improper use

Use by unskilled persons or those who have not read and under- stood the instructions in the manual is forbidden.

The introduction of inflammable, explosive and toxic liquids into the appliance is prohibited.

Use of the appliance in a potentially inflammable or explosive atmosphere is forbidden.

The use of non-original spare parts and any other spare parts not specifically intended for the model in question is prohibited.

All modifications to the appliance are prohibited. Any modifications made to the appliance shall render warranty.

4.4Main components

B1 Adjustable spray nozzle

B2 Lance

B3 Gun with safety catch

B4 Power supply cable with plug

B5 High pressure hose

B6 Detergent tank

B7 Quick Connector

4.4.1Accessories

C1 Nozzle cleaning tool

C2 Handle

C3 Hose reel

4.5Safety devices

Caution - Danger!

Do not tamper with or adjust the safety valve set-

ting.

-Safety valve and pressure limiting valve.

The safety valve is also a pressure limiting valve. When the gun trigger is released, the valve opens and the water recirculates

through the pump inlet.

- Safety catch (D): prevents accidental spraying of water.

5ELECTRICAL CONNECTION

5.1Assembly

Caution - Danger!

All installation and assembly operations must be performed with the appliance disconnected from the mains power supply.

The assembly sequence is illustrated in FIG.2.

5.2Electrical connection

The electrical connection should be made by a qualified electrician and should comply with regulations.

Caution - Danger!

Check that the electrical supply voltage and frequen- cy (V-Hz) correspond to those specified on the appliance data plate (FIG.2). The appliance should only be connected to a mains power supply equipped with an adequate earth connection and a differential security breaker (30 mA) to cut off the electricity supply in the instance of a short circuit.

5.2.1Use of extension cables

Use cables featuring “IPX5” protection level.

The cross-section of the extension cable should be pro- portionate to its length; the longer it is, the greater its cross-section should be.

Follow the instructions in Table I on page 5.

Inadequate extension cables can be dangerous.

5.3Water supply connection

Caution - Danger!

Only clean or filtered water should be used for intake. The delivery of the water intake tap should be equal to that of pump capacity.

Place the appliance as close to the water supply system as possible.

5.3.1Connection points

• Water outlet (OUTLET)

n Water inlet with filter (INLET)

5.3.2Connection to the mains water supply

The appliance can be connected directly to the mains drinking water supply only if the supply hose is fitted with a backflow preventer valve as per current regulations in force. Make sure that the hose is at least Ø 13 mm and that it is reinforced.

6STARTING THE APPLIANCE

6.1Connecting to the mains water system / water supply Detergent flow is adjusted using the regulator (F).

6.1.1Warning. Comply strictly with the technical regulations and standards of the local water supply company.

Ensure that the water mains connection complies with the data provided in the appliance’s technical specifications.

6.1.2Connect the water supply hose (not supplied) to the appliance’s intake connection (FIG.2.3).

6.1.3Turn on the water supply.

6.1.4Vent the air from the appliance. To vent the air from the appliance, set the nozzle (B1 FIG.1) in low pressure mode (fully forward) and press the trigger (first releasing the safety catch FIG. 4 Ref. D if necessary) until the water which flows out is free from air bubbles. When done, return the nozzle to the high pressure setting.

16