Craftsman 919.672241, D28235 owner manual Maintenance

Page 13

8.Turn fuel valve to the ON position, 1/4 turn counterclockwise.

9.Move the choke control lever to

the CHOKE ON position and

the throttle control to the FAST

position. NOTE: No choke is needed to start a warm engine.

Choke

Control

Throttle

Control

Fuel Valve Knob

10.Pull starter grip slowly until you feel resistance, then pull briskly. Return starter grip gently. Pull rope with a rapid full arm stroke. Let rope rewind slowly. Repeat if necessary.

If the engine does not start after two pulls, pull the trigger to relieve the

pressure.

11.If the choke was used to start the engine, move the choke lever to the OFF position.

12.Depress trigger on gun to start water flow. NOTE: Stand on a stable surface and grip gun/spray wand firmly with both hands. Expect the gun to kick back when triggered.

13.Release trigger to stop water flow.

14.Adjust nozzle spray for the task being performed. See How To Use Spray Wand instructions in this section.

DO NOT let hoses come in contact with

very hot engine muffler during or immediately after use of your pressure washer.

MAINTENANCE

When performing maintenance, you may be exposed to hot surfaces, water pressure, or moving parts that can cause

serious injury or death! Before performing any maintenance or repair, disconnect spark plug wire, let engine cool and release all water pressure. The engine contains flammable fuel. DO NOT smoke or work near open flames while performing maintenance.

To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high-temperatures or dusty conditions, more frequent maintenance checks will be required.

13- ENG

D28235

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Pressure Washer Table of Contents Safety Guidelines Definitions Specification ChartModel No 919-672241 Pressure Washer EngineRisk of Explosion or Fire Maintenance InstructionsRisk to Breathing Risk of Chemical Burn Risk to Fluid InjectionRisk of Electrical Shock Risk of Unsafe OperationRisk of HOT Surfaces BOX Contents Assembly Throttle Control Lever Controls engine speed OperationPressure Washer Terminology 40º fan spray Narrow jet stream HOW to Apply Chemicals and Cleaning SolventsBefore Starting Maintenance Customer Responsibilities Table Maintenance TaskEngine Pressure WasherTo Change Oil CleaningInspect Pump Clean and Replace Spark PlugEngine Preparation StorageProblem Cause Correction Troubleshooting GuideProblem Cause Correction Pump Pulsates ProblemcausePressure Washer Model Number Repair PartsKey# Description Not Shown Pressure Pump Model Number D28703 Cylinder Barrel Honda Engine Model Number GCV160ADescription Part Number Description Part Number Qty OIL PANCrankshaft Repair Parts Crankshaft Pulley Description Part Number Qty FAN Cover Carburetor AIR Cleaner Muffler Flywheel Control Labels Garantie Complète DE UN AN SUR LES Laveuses À Pression Table DES MatièresSears Canada, Inc., Toronto, Ont. M5B 2B8 Mesures DE Sécurité Définitions Tableau DES SpécificationsRenseignements SUR LA Sécurité DU Consommateur De modèle 919.672241 Laveuse à pressionRisque Dexplosion OU D’INCENDIE Mesures DE Sécurité ImportantesPrévention Risque PAR Inhalation PréventionRisque Risque Dune Utilisation NON Sécuritaire Risque Prévention Contenu DE LA BoîteAssemblage Levier de commande des gaz Commande la Commande détrangleur Ouvre et ferme laUtilisation Laveuse À PressionUtilisation Terminologie DES Laveuses À PressionRéglage DE LA Pression Utilisation DE LA LanceApplication DES Produits CHIMIQUES/SOLVANTS DE Nettoyage Arrêt DE LA Laveuse À PressionRemarque La source deau doit fournir un Avant LE DémarrageMinimum de 5 gallons par minute à 20 lb/po2 Remarque Assurez-vous que le robinet deLa source deau est ouvert Entretien« Utilisation de la lance » de cette section NE laissez PAS Vérification du niveau d’huile Tableau DES Responsabilités DU Client Tache D’ENTRETIENMoteur Laveuse À PressionFiltre à air Changement de l’huileInspection NettoyagePompe Nettoyage et remplacement de la bougie d’allumageLance DE Vaporisation Préparation du moteur EntreposageProblème Cause Correction Guide DE DépannageProblème 55- FR ’article De pièce Description De modèle de la laveuse à pressionNon illustré De modèle de la pompe refoulante D28703 Corps DE Cylindre No de modèle du moteur Honda GCV160ARéf Description De pièce Carter D’HUILE Vilebrequin Teikoku Poulie D’ARBRE À Cames Démarreur À Rappel Couvercle DE Ventilateur Réf Description De pièce Qté CarburateurFiltre À AIR Silencieux Volant Moteur Commande Étiquettes Get it fixed, at your home or ours

919.672241, D28235 specifications

The Craftsman D28235,919.672241 is a noteworthy product in the realm of power tools, designed with the user in mind to enhance efficiency and performance in various tasks. This tool combines robust build quality with advanced features, making it suitable for both DIY enthusiasts and professional contractors.

One of the standout characteristics of the Craftsman D28235 is its powerful motor. With a high wattage rating, this tool delivers consistent performance even under strenuous conditions. The motor is engineered to provide optimal torque, enabling users to tackle demanding applications with ease, whether cutting, grinding, or polishing.

In terms of design, the Craftsman D28235 features an ergonomic handle that ensures comfort during extended use. The grip is thoughtfully designed to reduce user fatigue, allowing for better control and precision. This aspect is particularly beneficial when engaging in intricate tasks that require steady hands and attention to detail.

Another significant feature is its variable speed control. This technology allows users to adjust the speed of the tool according to the particular task requirements. Whether working with delicate materials or more robust surfaces, users can modify the RPM to achieve the desired results without damaging the workpiece. This flexibility positions the D28235 at the forefront of versatile power tools.

The tool also benefits from an integrated safety mechanism, including a safety switch to prevent accidental startups. This feature is crucial for ensuring user safety, providing peace of mind when storing or handling the tool. Additionally, the D28235 boasts a durable casing that protects its internal components from dust and debris, further enhancing longevity.

Compatibility with a variety of attachments is another advantage of the Craftsman D28235. This adaptability allows users to equip the tool with different blades, discs, or accessories, expanding its functionality for various tasks, including grinding, sanding, and cutting.

Lastly, its lightweight design contributes to the overall usability, making it easy to maneuver and transport. Whether you are working on-site or at home, the Craftsman D28235,919.672241 stands out as a reliable and efficient tool that integrates advanced technology with user-centric features, solidifying its place in the toolkit of anyone serious about craftsmanship and quality work.
Top Page Image Contents