Craftsman 919.672241, D28235 owner manual To Change Oil, Inspect, Cleaning

Page 15

To Change Oil

Drain the engine oil when the engine is warm. Warm oil drains quickly and completely.

1.Turn the fuel valve to the OFF position, 1/4 turn clockwise.

2.Place a suitable container next to the engine to catch the used oil.

3.Remove filler cap/dipstick and drain the oil into the container by tipping the engine toward the oil filler neck.

Oil Filler Neck

Oil Filler

Cap/Dipstick

Upper Limit

Lower Limit

NOTE: Please dispose of used motor oil in a manner that is compatible with the environment. It is recommended to take used oil in a sealed container to your local recycling center or service station for reclamation. Do not throw it in the trash or pour it on the ground or down a drain.

4.With the engine in a level position, fill to the upper limit mark on the dipstick with SAE 10W-30 oil. Engine oil capacity is 0.58 quart (.055 liter). NOTE: Other viscosities shown in the chart in the “To Check Oil” paragraph may be used.

5.Replace the oil filler cap/dipstick securely.

Air Cleaner

A dirty air cleaner will restrict air flow to the carburetor and cause poor engine performance. Inspect the filter each time the engine is operated. Clean the filter more frequently if the engine is operated in very dusty areas.

NOTICE: Operating the engine without a filter, will allow dirt to enter the engine, causing rapid engine wear. This type of damage is not covered under the warranty.

Inspect

1.Press the latch tabs on the top of the air cleaner cover and remove the cover. Check the filter to be sure it is clean and in good condition.

2.Reinstall the filter and air cleaner cover.

 

Air Cleaner Body

 

Filter

Air

 

 

 

 

 

Cleaner

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cover

 

 

 

 

 

Latch

 

 

 

 

 

Tabs

 

 

 

 

 

Lower

Air

Duct

Tabs

 

 

 

 

 

 

 

Cleaning

1.Tap the filter several times on a hard surface to remove dirt or blow compressed air [not exceeding 30 psi (207kPa, 1.2 kg/cm2) through the filter from the clean side that faces the engine. Never try to brush off dirt. Brushing will force dirt into the fibers.

2.Wipe dirt from the air cleaner body and cover using a moist rag. Be careful to prevent dirt from entering the air duct that leads to the carburetor.

15- ENG

D28235

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Pressure Washer Table of Contents Engine Specification ChartSafety Guidelines Definitions Model No 919-672241 Pressure WasherMaintenance Instructions Risk of Explosion or FireRisk to Breathing Risk of Chemical Burn Risk to Fluid InjectionRisk of Unsafe Operation Risk of Electrical ShockRisk of HOT Surfaces BOX Contents Assembly Throttle Control Lever Controls engine speed OperationPressure Washer Terminology 40º fan spray Narrow jet stream HOW to Apply Chemicals and Cleaning SolventsBefore Starting Maintenance Pressure Washer Maintenance TaskCustomer Responsibilities Table EngineCleaning To Change OilInspect Pump Clean and Replace Spark PlugEngine Preparation StorageProblem Cause Correction Troubleshooting GuideProblem Cause Correction Pump Pulsates ProblemcauseRepair Parts Pressure Washer Model NumberKey# Description Not Shown Pressure Pump Model Number D28703 Honda Engine Model Number GCV160A Cylinder BarrelDescription Part Number Description Part Number Qty OIL PANCrankshaft Repair Parts Crankshaft Pulley Description Part Number Qty FAN Cover Carburetor AIR Cleaner Muffler Flywheel Control Labels Table DES Matières Garantie Complète DE UN AN SUR LES Laveuses À PressionSears Canada, Inc., Toronto, Ont. M5B 2B8 De modèle 919.672241 Laveuse à pression Tableau DES SpécificationsMesures DE Sécurité Définitions Renseignements SUR LA Sécurité DU ConsommateurRisque PAR Inhalation Prévention Mesures DE Sécurité ImportantesRisque Dexplosion OU D’INCENDIE PréventionRisque Risque Dune Utilisation NON Sécuritaire Risque Prévention Contenu DE LA BoîteAssemblage Laveuse À Pression Commande détrangleur Ouvre et ferme laLevier de commande des gaz Commande la UtilisationUtilisation DE LA Lance Terminologie DES Laveuses À PressionUtilisation Réglage DE LA PressionApplication DES Produits CHIMIQUES/SOLVANTS DE Nettoyage Arrêt DE LA Laveuse À PressionRemarque Assurez-vous que le robinet de Avant LE DémarrageRemarque La source deau doit fournir un Minimum de 5 gallons par minute à 20 lb/po2Entretien La source deau est ouvert« Utilisation de la lance » de cette section NE laissez PAS Laveuse À Pression Tableau DES Responsabilités DU Client Tache D’ENTRETIENVérification du niveau d’huile MoteurNettoyage Changement de l’huileFiltre à air InspectionNettoyage et remplacement de la bougie d’allumage PompeLance DE Vaporisation Préparation du moteur EntreposageProblème Cause Correction Guide DE DépannageProblème 55- FR ’article De pièce Description De modèle de la laveuse à pressionNon illustré De modèle de la pompe refoulante D28703 No de modèle du moteur Honda GCV160A Corps DE CylindreRéf Description De pièce Carter D’HUILE Vilebrequin Teikoku Poulie D’ARBRE À Cames Démarreur À Rappel Couvercle DE Ventilateur Réf Description De pièce Qté CarburateurFiltre À AIR Silencieux Volant Moteur Commande Étiquettes Get it fixed, at your home or ours

919.672241, D28235 specifications

The Craftsman D28235,919.672241 is a noteworthy product in the realm of power tools, designed with the user in mind to enhance efficiency and performance in various tasks. This tool combines robust build quality with advanced features, making it suitable for both DIY enthusiasts and professional contractors.

One of the standout characteristics of the Craftsman D28235 is its powerful motor. With a high wattage rating, this tool delivers consistent performance even under strenuous conditions. The motor is engineered to provide optimal torque, enabling users to tackle demanding applications with ease, whether cutting, grinding, or polishing.

In terms of design, the Craftsman D28235 features an ergonomic handle that ensures comfort during extended use. The grip is thoughtfully designed to reduce user fatigue, allowing for better control and precision. This aspect is particularly beneficial when engaging in intricate tasks that require steady hands and attention to detail.

Another significant feature is its variable speed control. This technology allows users to adjust the speed of the tool according to the particular task requirements. Whether working with delicate materials or more robust surfaces, users can modify the RPM to achieve the desired results without damaging the workpiece. This flexibility positions the D28235 at the forefront of versatile power tools.

The tool also benefits from an integrated safety mechanism, including a safety switch to prevent accidental startups. This feature is crucial for ensuring user safety, providing peace of mind when storing or handling the tool. Additionally, the D28235 boasts a durable casing that protects its internal components from dust and debris, further enhancing longevity.

Compatibility with a variety of attachments is another advantage of the Craftsman D28235. This adaptability allows users to equip the tool with different blades, discs, or accessories, expanding its functionality for various tasks, including grinding, sanding, and cutting.

Lastly, its lightweight design contributes to the overall usability, making it easy to maneuver and transport. Whether you are working on-site or at home, the Craftsman D28235,919.672241 stands out as a reliable and efficient tool that integrates advanced technology with user-centric features, solidifying its place in the toolkit of anyone serious about craftsmanship and quality work.
Top Page Image Contents