Craftsman 919.672241, D28235 owner manual Storage, Engine Preparation

Page 17

STORAGE

ENGINE

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, hose or tank during storage. Also, experience indicates that alcohol-blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Never use engine or carburetor cleaner products in the fuel tank or per- manent damage may occur.

Engine Preparation

1.First add a fuel stabilizer to the fuel tank.

2.Run pressure washer for a full 5 minutes to allow fuel stabilizer to enter the fuel system.

While preparing the

engine make sure

water supply is turned on and flowing to the unit. NEVER run unit without water supply running through pump. Failure to do so will cause pump damage.

3.Next shut off engine and disconnect the water supply.

4.Disconnect the spark plug wire and remove the spark plug.

5.Add one teaspoon of oil through the spark plug hole.

6.Place rag over spark plug hole and pull the recoil a few times to lubricate the combustion chamber.

7.Replace the spark plug, but do not connect the spark plug wire.

PUMP

1.Drain all water from high pressure hose, coil it, and store it in cradle of the pressure washer handle.

2.Drain all water from spray gun and spray wand by holding spray gun in a vertical position with nozzle end pointing down and squeezing trigger. Store in gun/hose holder.

3.Store chemical hose, high pressure hose, spray gun, and spray wand so they are protected from dam-

age, such as being run over. It is recommended that you follow these steps to protect the internal seals of the pressure washer when STORING THE UNIT FOR MORE THAN 30 DAYS AND/OR WHEN FREEZING

TEMPERATURES ARE EXPECTED. *RV antifreeze needs to be run through the pump as outlined in the steps below.

4.Obtain a funnel, six ounces of *RV antifreeze, and approximately 36 inches of garden hose with a male hose connector attached to one end.

Use only RV antifreeze. Any other

antifreeze is corrosive and can damage pump.

5.Disconnect spark plug wire.

6.Connect 36 inch length of hose to water inlet of pump.

7.Add *RV antifreeze to hose as shown.

17- ENG

D28235

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Pressure Washer Table of Contents Safety Guidelines Definitions Specification ChartModel No 919-672241 Pressure Washer EngineRisk to Breathing Maintenance InstructionsRisk of Explosion or Fire Risk of Chemical Burn Risk to Fluid InjectionRisk of HOT Surfaces Risk of Unsafe OperationRisk of Electrical Shock BOX Contents Assembly Throttle Control Lever Controls engine speed OperationPressure Washer Terminology 40º fan spray Narrow jet stream HOW to Apply Chemicals and Cleaning SolventsBefore Starting Maintenance Customer Responsibilities Table Maintenance TaskEngine Pressure WasherInspect CleaningTo Change Oil Pump Clean and Replace Spark PlugEngine Preparation StorageProblem Cause Correction Troubleshooting GuideProblem Cause Correction Pump Pulsates ProblemcauseKey# Description Repair PartsPressure Washer Model Number Not Shown Pressure Pump Model Number D28703 Description Part Number Honda Engine Model Number GCV160ACylinder Barrel Description Part Number Qty OIL PANCrankshaft Repair Parts Crankshaft Pulley Description Part Number Qty FAN Cover Carburetor AIR Cleaner Muffler Flywheel Control Labels Sears Canada, Inc., Toronto, Ont. M5B 2B8 Table DES MatièresGarantie Complète DE UN AN SUR LES Laveuses À Pression Mesures DE Sécurité Définitions Tableau DES SpécificationsRenseignements SUR LA Sécurité DU Consommateur De modèle 919.672241 Laveuse à pressionRisque Dexplosion OU D’INCENDIE Mesures DE Sécurité ImportantesPrévention Risque PAR Inhalation PréventionRisque Risque Dune Utilisation NON Sécuritaire Risque Prévention Contenu DE LA BoîteAssemblage Levier de commande des gaz Commande la Commande détrangleur Ouvre et ferme laUtilisation Laveuse À PressionUtilisation Terminologie DES Laveuses À PressionRéglage DE LA Pression Utilisation DE LA LanceApplication DES Produits CHIMIQUES/SOLVANTS DE Nettoyage Arrêt DE LA Laveuse À PressionRemarque La source deau doit fournir un Avant LE DémarrageMinimum de 5 gallons par minute à 20 lb/po2 Remarque Assurez-vous que le robinet de« Utilisation de la lance » de cette section NE laissez PAS EntretienLa source deau est ouvert Vérification du niveau d’huile Tableau DES Responsabilités DU Client Tache D’ENTRETIENMoteur Laveuse À PressionFiltre à air Changement de l’huileInspection NettoyageLance DE Vaporisation Nettoyage et remplacement de la bougie d’allumagePompe Préparation du moteur EntreposageProblème Cause Correction Guide DE DépannageProblème 55- FR ’article De pièce Description De modèle de la laveuse à pressionNon illustré De modèle de la pompe refoulante D28703 Réf Description De pièce No de modèle du moteur Honda GCV160ACorps DE Cylindre Carter D’HUILE Vilebrequin Teikoku Poulie D’ARBRE À Cames Démarreur À Rappel Couvercle DE Ventilateur Réf Description De pièce Qté CarburateurFiltre À AIR Silencieux Volant Moteur Commande Étiquettes Get it fixed, at your home or ours

919.672241, D28235 specifications

The Craftsman D28235,919.672241 is a noteworthy product in the realm of power tools, designed with the user in mind to enhance efficiency and performance in various tasks. This tool combines robust build quality with advanced features, making it suitable for both DIY enthusiasts and professional contractors.

One of the standout characteristics of the Craftsman D28235 is its powerful motor. With a high wattage rating, this tool delivers consistent performance even under strenuous conditions. The motor is engineered to provide optimal torque, enabling users to tackle demanding applications with ease, whether cutting, grinding, or polishing.

In terms of design, the Craftsman D28235 features an ergonomic handle that ensures comfort during extended use. The grip is thoughtfully designed to reduce user fatigue, allowing for better control and precision. This aspect is particularly beneficial when engaging in intricate tasks that require steady hands and attention to detail.

Another significant feature is its variable speed control. This technology allows users to adjust the speed of the tool according to the particular task requirements. Whether working with delicate materials or more robust surfaces, users can modify the RPM to achieve the desired results without damaging the workpiece. This flexibility positions the D28235 at the forefront of versatile power tools.

The tool also benefits from an integrated safety mechanism, including a safety switch to prevent accidental startups. This feature is crucial for ensuring user safety, providing peace of mind when storing or handling the tool. Additionally, the D28235 boasts a durable casing that protects its internal components from dust and debris, further enhancing longevity.

Compatibility with a variety of attachments is another advantage of the Craftsman D28235. This adaptability allows users to equip the tool with different blades, discs, or accessories, expanding its functionality for various tasks, including grinding, sanding, and cutting.

Lastly, its lightweight design contributes to the overall usability, making it easy to maneuver and transport. Whether you are working on-site or at home, the Craftsman D28235,919.672241 stands out as a reliable and efficient tool that integrates advanced technology with user-centric features, solidifying its place in the toolkit of anyone serious about craftsmanship and quality work.
Top Page Image Contents