Craftsman D28235, 919.672241 owner manual Pump, Clean and Replace Spark Plug

Page 16

Clean and Replace Spark Plug

Change the spark plug every 100 hours of operation or once each year, whichever comes first. This will help your engine to start easier and run better.

.030” (0.76 MM)

Wire Gauge

Resistor

PUMP

This screen filter should be checked periodically and cleaned if necessary.

1.Remove filter by grasping end and removing it from water inlet of pump as shown.

2.Clean filter by flushing it with water on both sides.

3.Re-insert filter into water inlet of pump. NOTE: Cone side faces out.

NOTE: Do not operate pressure washer without filter properly installed.

Filter Screen

WAND

If the nozzle becomes clogged with foreign materials, such as dirt, excessive pressure may develop. If the nozzle becomes partially clogged or restricted, the pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit supplied and the following instructions:

1.Shut off the pressure washer and turn off the water supply.

2.Disconnect spark plug wire.

3.Pull trigger on gun handle to relieve any water pressure.

4.Disconnect the wand from the gun.

5.Remove the nozzle from the end of the wand with the 2mm allen wrench provided as shown.

6.Clean the nozzle using the nozzle cleaner provided or a straightened paper clip. Insert into the nozzle end and work back and forth until obstruction is removed.

7.Direct water supply into nozzle end to backflush loosened particles for 30 seconds.

8.Reconnect spark plug wire.

9.Reassemble the nozzle to the wand. Tighten securely to prevent leaks.

10.Reconnect wand to gun and turn on water supply.

11.Start pressure washer and place wand into high pressure setting to test.

D28235

16- ENG

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Pressure Washer Table of Contents Specification Chart Safety Guidelines DefinitionsModel No 919-672241 Pressure Washer EngineRisk of Explosion or Fire Maintenance InstructionsRisk to Breathing Risk to Fluid Injection Risk of Chemical BurnRisk of Electrical Shock Risk of Unsafe OperationRisk of HOT Surfaces BOX Contents Assembly Operation Throttle Control Lever Controls engine speedPressure Washer Terminology HOW to Apply Chemicals and Cleaning Solvents 40º fan spray Narrow jet streamBefore Starting Maintenance Maintenance Task Customer Responsibilities TableEngine Pressure WasherTo Change Oil CleaningInspect Clean and Replace Spark Plug PumpStorage Engine PreparationTroubleshooting Guide Problem Cause CorrectionProblem Cause Correction Problemcause Pump PulsatesPressure Washer Model Number Repair PartsKey# Description Not Shown Pressure Pump Model Number D28703 Cylinder Barrel Honda Engine Model Number GCV160ADescription Part Number OIL PAN Description Part Number QtyCrankshaft Repair Parts Crankshaft Pulley Description Part Number Qty FAN Cover Carburetor AIR Cleaner Muffler Flywheel Control Labels Garantie Complète DE UN AN SUR LES Laveuses À Pression Table DES MatièresSears Canada, Inc., Toronto, Ont. M5B 2B8 Tableau DES Spécifications Mesures DE Sécurité DéfinitionsRenseignements SUR LA Sécurité DU Consommateur De modèle 919.672241 Laveuse à pressionMesures DE Sécurité Importantes Risque Dexplosion OU D’INCENDIEPrévention Risque PAR Inhalation PréventionRisque Risque Dune Utilisation NON Sécuritaire Contenu DE LA Boîte Risque PréventionAssemblage Commande détrangleur Ouvre et ferme la Levier de commande des gaz Commande laUtilisation Laveuse À PressionTerminologie DES Laveuses À Pression UtilisationRéglage DE LA Pression Utilisation DE LA LanceArrêt DE LA Laveuse À Pression Application DES Produits CHIMIQUES/SOLVANTS DE NettoyageAvant LE Démarrage Remarque La source deau doit fournir unMinimum de 5 gallons par minute à 20 lb/po2 Remarque Assurez-vous que le robinet deLa source deau est ouvert Entretien« Utilisation de la lance » de cette section NE laissez PAS Tableau DES Responsabilités DU Client Tache D’ENTRETIEN Vérification du niveau d’huileMoteur Laveuse À PressionChangement de l’huile Filtre à airInspection NettoyagePompe Nettoyage et remplacement de la bougie d’allumageLance DE Vaporisation Entreposage Préparation du moteurGuide DE Dépannage Problème Cause CorrectionProblème 55- FR De modèle de la laveuse à pression ’article De pièce DescriptionNon illustré De modèle de la pompe refoulante D28703 Corps DE Cylindre No de modèle du moteur Honda GCV160ARéf Description De pièce Carter D’HUILE Vilebrequin Teikoku Poulie D’ARBRE À Cames Démarreur À Rappel Couvercle DE Ventilateur Carburateur Réf Description De pièce QtéFiltre À AIR Silencieux Volant Moteur Commande Étiquettes Get it fixed, at your home or ours

919.672241, D28235 specifications

The Craftsman D28235,919.672241 is a noteworthy product in the realm of power tools, designed with the user in mind to enhance efficiency and performance in various tasks. This tool combines robust build quality with advanced features, making it suitable for both DIY enthusiasts and professional contractors.

One of the standout characteristics of the Craftsman D28235 is its powerful motor. With a high wattage rating, this tool delivers consistent performance even under strenuous conditions. The motor is engineered to provide optimal torque, enabling users to tackle demanding applications with ease, whether cutting, grinding, or polishing.

In terms of design, the Craftsman D28235 features an ergonomic handle that ensures comfort during extended use. The grip is thoughtfully designed to reduce user fatigue, allowing for better control and precision. This aspect is particularly beneficial when engaging in intricate tasks that require steady hands and attention to detail.

Another significant feature is its variable speed control. This technology allows users to adjust the speed of the tool according to the particular task requirements. Whether working with delicate materials or more robust surfaces, users can modify the RPM to achieve the desired results without damaging the workpiece. This flexibility positions the D28235 at the forefront of versatile power tools.

The tool also benefits from an integrated safety mechanism, including a safety switch to prevent accidental startups. This feature is crucial for ensuring user safety, providing peace of mind when storing or handling the tool. Additionally, the D28235 boasts a durable casing that protects its internal components from dust and debris, further enhancing longevity.

Compatibility with a variety of attachments is another advantage of the Craftsman D28235. This adaptability allows users to equip the tool with different blades, discs, or accessories, expanding its functionality for various tasks, including grinding, sanding, and cutting.

Lastly, its lightweight design contributes to the overall usability, making it easy to maneuver and transport. Whether you are working on-site or at home, the Craftsman D28235,919.672241 stands out as a reliable and efficient tool that integrates advanced technology with user-centric features, solidifying its place in the toolkit of anyone serious about craftsmanship and quality work.
Top Page Image Contents