Craftsman 580.752 owner manual Remove Pressure Washer from Carton, Carton Contents

Page 6

Yourpressure washer requires some assembly and is

ready for use only after it has been properly serviced with the recommended oil and fuel.

If you have any problems with the assembly of your pressure washer, please call the pressure washer helpline at 1-800-222-3t36.

IMPORTANT: Any attempt to run the engine before it has been serviced with the recommended oil will result

in an engine failure.

2.Place nozzle extension, turbowand and spray gun into holder.

REMOVE PRESSURE WASHER FROM CARTON

Open carton and slice two corners opposite guide handle from top to bottom so the panel can be folded down flat.

Remove fillers, accessories and parts bag shipped with your pressure washer.

Remove the pressure washer out the open end of the carton.

Check carton for additional loose parts.

CARTON CONTENTS

Check all contents, If any parts are missing or damaged, cell the pressure washer helpline at t-800-222-3136,

The main unit

High pressure hose

Spray gun

Nozzle extension with adjustable nozzle

Turbo wand

Accessory holder

Engine oil

Parts bag (which includes items listed below) Owner's manual

Registration card

Become familiar with each piece before assembling the pressure washer. Compare contents against the view on page 5. If any parts are missing or damaged, call the pressure washer helpline at 1-800-222_3136.

ASSEMBLING YOUR PRESSURE WASHER

Your Craftsman pressure washer was mostly

assembled at the factory, However, you will need to perform these tasks before you can operate your pressure washer:

1.Add oil to engine crankcase.

2.Add fuel to fuel tank.

3.Connect high pressure hose to spray gun and pump.

4.Connect water supply to pump.

Attach Accessory Holder

1, Place accessory holderonto top of handle,

Add Engine Oil

IMPORTANT: Any attempt to crank or start the engine before it has been properly serviced with the

recommended oil may result in an engine failure,

NOTE: When adding oil to the engine crankcase, use only high quality detergent oil rated with API service classification SF, SG, SH, SJ or higher rated SAE 30 weight, DO NOT use special additives,

1.Choose a viscosity according to the following table.

STARTING TE_ FERATURE RANGE AINTICI PATE E) BEFORE NEXT OIL CHANGE

*The use of multi-viscesiN oils (5W-30, 10W-30, etc.) in temperatures above 40=F (4=C) will result in higher than normal oil consumption. When using a multi- viscosity oil, check oil more frequently.

**If using SAE 30 oil in temperatures below 40=F

(_=C), it will result in hard starting and possible engine bore damage due to inadequate lubrication.

2.Place pressure washer on a level surface.

3.Clean area around oil fill.

4.Remove oil fill cap and dipstick.

5.Wipe dipstick clean, insert it into oil fill hole and tighten securely, remove dipsticK. Add recommended oil up to "Fall" mark on dipstick.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Horsepower Hours Mon. FrL 8 a.m. to 5 p.m. CTSEARS, Roebuck and CO., Hoffman Estates, IL 60179 U.S.A Hazard Symbols and Meanings Sears, Roebuck and Co., Dept WA, Hoffman Estates, ILKeep spray nozzle between 8 to 24 inches away from cleaning SurfacesiContact Searsi Do not operate pressure washer above rated pressureiKnow Your Pressure Washer Carton Contents Remove Pressure Washer from CartonAssembling Your Pressure Washer Damaged Checklist Before StartingInspect inlet Review the unit 1oensure you have performed allHOW to USE Your Pressure To Start Your Pressure WasherUsing the Turbo Nozzle How To Use the Adjustable NozzleBetween 8 to 24 inches away from cleaning surface Detergent app!itionFor Rinsing Pressure Washer RinsingTo apply detergent, follow these steps Automatic Cool Down System Thermal ReliefOwners Responsibilities Product SpecificationsPressure Washer Maintenance General RecommendationsPurge Pump of Air and Contaminants Nozzle MaintenanceCheck Gun and Nozzle Extension Check In-Line FilterEngine Maintenance Pump MaintenanceChanging Oil After Each USE Service Air CleanerService Spark Plug Yearly, whichever occurs firstGeneral Winter StorageLong Term Storage CheCkand € ean Pump Has following problemsTo produce BlOcks in OutlethoseiPage 194298GS Optiona! Access0ries NOt II!ustratedDescription 190249GS190575GS 190827GS190832GS 19063-GS456 ENGINE, 3.75 HP, Briggs and Stratton, 10D902 Exploded View200 306523163 393 356356A ENGINE, 3.75 HP, Briggs and Stratton, 10D902 Parts List Sears Emission Control Defects Warranty Provisions Sears Emission Control Defects Warranty CoverageAir cleaner Intake manifold Length of CoverageSimbolos de Peligro y Significados Sears, Roebuck and Co., Dept WA, Hoffman Estates, ILPeligro AdvertenciaPrecaucion Conozca SU Maquina Lavadora DE Presion Reco!e¢iOnde DetergenteFijar el Poseedor Accesorio Contenido DE LA CajaMontaje DE LA Maquina Lavadora a Presion Agregue Aceite de MotorLista de Revision Previa al Arranque del Motor Agregue GasolinaConecte la Manguera y el Surninistro de Agua a la Bornba Dahado, Nunca agua de cala de siphonCbmo Darle Arranque a su Mquina Lavadora a Presibn Como Usar SU Maquina Lavadora a PresionPRECAUCI6N Para comenzar motor despusCSmo Usar la Boquilla a Chorro CSmo Detener su Mquina Lavadora a PresiSnCSmo Usar la Boquilla Ajustable La boquilla a chorro hace girar la cordente de alta presibnAplicaci6n del Detergente Usando la Boquilla Ajustable Enjuage de la Mbquina Lavadora a PresionSistema de Enfriamiento Autom&tico Alivio T6rmico Responsabilidades DEL Propietario Recomendaciones GeneralesMantenimiento DE LA Maquina Lavadora a Presion Cambio de Aceite Revisi6n del Nivel del AceiteMantenimiento de los Anillos O Mantenimiento de la BombaServicio del Depurador de Aire Despues DE Cada USOProporcione Servicio a la Bujia PartAlmacenamiento Para Invierno Precaucion Almacenamiento ProlongadoOtros Funciona Mali Labuj!a El motor No arranCa o arrancayRemplace Drene ei tanqde de gaS01ina iieneioCobarturs Consiguiante Anytime, day or night A. and Canada
Top Page Image Contents