Briggs & Stratton 2550 PSI manual Connect Hose and Water Supply to Pump

Page 10

Connect Hose and Water Supply to Pump

NOTICE

DO NOT run the pump without the water supply connected and turned on.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

NOTE: Remove and discard the shipping caps from the pump’s high pressure outlet and water inlet before attaching hoses.

1.Uncoil high pressure hose and attach one end of hose to base of spray gun. Tighten by hand.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

•NEVER connect high pressure hose to nozzle extension.

•Keep high pressure hose connected to pump and spray gun while system is pressurized.

•Always be certain spray gun, nozzles and accessories are correctly attached.

2.Attach other end of high pressure hose to high pressure outlet on pump. Tighten by hand.

3.Before connecting garden hose to water inlet, inspect inlet screen (A). Clean screen if it contains debris or have it replaced if damaged. DO NOT run pressure washer if inlet screen is damaged.

A

4.Run water through your garden hose for 30 seconds to clean out any debris.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).

NOTICE

Using a One Way Valve (vacuum breaker or check valve) at pump inlet can cause pump or inlet connector damage.

•There MUST be at least ten feet (3 m) of unrestricted garden hose between the pressure washer inlet and any device, such as a vacuum breaker or check valve.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

5.Connect the garden hose (not to exceed 50 feet in length) to the water inlet. Tighten by hand.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

•Always wear safety goggles when using this equipment or in vicinity of where equipment is in use.

•Before starting the pressure washer, be sure you are wearing adequate safety goggles.

•NEVER substitute safety glasses for safety goggles.

6.Turn ON the water, press red button (B) on the gun and squeeze the trigger to purge the pump system of air and impurities.

B

Checklist Before Starting Engine

Review the unit’s assembly to ensure you have performed all of the following.

1.Be sure to read the Operator Safety section and How to Use Your Pressure Washer in Operation section before using pressure washer.

2.Make sure handle is in place and secure.

3.Check that oil has been added to proper level in the engine crankcase.

4.Add proper fuel to fuel tank.

5.Check for properly tightened hose connections.

6.Check to make sure there are no kinks, cuts, or damage to high pressure hose.

7.Provide a proper water supply at an adequate flow.

10

BRIGGSandSTRATTON.COM

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual Engine Where to Find UsPressure Washer Date PurchasedTable of Contents Hazard Symbols and Meanings Operator SafetySafety Rules Equipment DescriptionWhen Adding or Draining Fuel Contact with muffler area can result in serious burns Broken bones, fractures, bruises, or sprains could resultUnintentional sparking can result in fire or electric shock Risk of eye injury Spray can splash back or propel objects High pressure spray may damage fragile items including glassUnpack Pressure Washer AssemblyAttach Handle and Accessory Tray Items in the carton includeFuel must meet these requirements Add Engine OilAdd Fuel High AltitudeChecklist Before Starting Engine Connect Hose and Water Supply to PumpFeatures and Controls Pressure Washer Location OperationClearances and Air Movement How to Start Your Pressure Washer How to Stop Your Pressure Washer How to Use Project Pro Nozzles How to Use Accessory TrayFollow these instructions to change Project Pro nozzles Usage Tips Cleaning and Applying DetergentTo apply detergent, follow these steps Automatic Cool Down System Thermal Relief Cleaning Detergent Siphoning TubePressure Washer Rinsing For RinsingMaintenance Schedule MaintenancePressure Washer Maintenance Check High Pressure Hose Nozzle MaintenanceRing Maintenance Check Detergent Siphoning TubeChecking Oil Level Engine MaintenanceOil Oil Recommendations Adding Engine OilService Spark Plug Service Air CleanerTo service the air cleaner, follow these steps Install spark plug and tighten firmlyAir Cooling System After Each UseKeep areas within heavy line clear of debris Winter Storage Long Term StorageTroubleshooting Problem Cause CorrectionOwner’s Warranty Responsibilities Emissions Control System WarrantyWarranties Emission Information MaintenanceClaims and Coverage Exclusions Limited Warranty Common Service Parts Product Specifications800 Manual del Operario Motor Dónde encontrarnosLimpiadora a Presión Fecha de compraMontaje Resolución de problemas GarantíasSeguridad de Operario Características y mandos OperandoDerscripción del equipo Seguridad de OperarioReglas de seguridad Riesgo de electrocución Opere el limpiadora a presión Solamente al aire libreCuando Pruebe LA Bujía DEL Motor Aviso Conecte el manubrio y bandeja accesoria MontajeDesembale la limpiadora a presión Los artículos que se encuentran en la caja sonEl combustible debe reunir los siguientes requisitos Agregar aceite al motorAgregue combustible Gran altitudLista de revision previa al arranque del motor Conecte la manguera y el suministro de agua a la bombaProporcione el suministro de agua adecuado Características y mandos Bomba Desarrolla alta presión de aguaCómo darle arranque a su máquina limpiadora a presión OperandoUbicación del limpiadora a presión Espacio libre alrededor del limpiadora a presiónAdvertencia Utilización de la bandeja de accesorios Cómo detener su máquina limpiadora a presiónLa Presión Alta Cómo usar las boquillas Project ProLa Presión Baja Para cambiar las boquillas de Project ProUso inclina Limpieza y aplicación del detergenteEnjuage de la máquina limpiadora a presión Para aplicar el detergente, siga los siguientes pasosLimpieza del tubo de inyección de detergente Sistema de enfriamiento automático alivio térmicoPlan de mantenimiento MantenimientoMantenimiento de la limpiadora a presión Chequee el tubo de sifón del detergente Revise y limpie el colador de entradaRevise la manguera de alta presión Revise la pistolaComprobación del nivel de aceite Mantenimiento del motorMantenimiento de los anillos o Aceite Recomendaciones sobre el aceiteServicio del depurador de aire Cambio de aceite del motorAfloje el tornillo a y quite la cubierta B Servicio del bujíaSistema de refrigeración de aire Despues de cada usoServicio del apagachispas BRIGGSandSTRATTON.COMAlmacenamiento para invierno Almacenamiento prolongadoResolución de problemas Problema Causa SoluciónResponsabilidades de la garantía del propietario GarantíasGarantía del sistema de control de emisiones Operaciones de mantenimiento que se enumeran en lasInformación sobre emisiones Garantía Limitada Servicio común despide Especificaciones del productoTemperatura del suministro

2550 PSI specifications

The Briggs & Stratton 2550 PSI pressure washer is a powerful cleaning tool designed to tackle a variety of outdoor tasks with ease. With a maximum cleaning power of 2550 PSI, this machine is well-equipped for efficiently removing dirt, grime, and stubborn stains from surfaces such as driveways, patios, decks, and vehicles.

One of the standout features of the Briggs & Stratton 2550 PSI pressure washer is its durable and reliable engine. Powered by a Briggs & Stratton 550 Series engine, it delivers consistent performance and dependable starts, allowing users to get to work without the frustration of engine failure. This engine is designed with an overhead valve (OHV) configuration, which increases efficiency while reducing emissions.

The pressure washer is also user-friendly, featuring a convenient push-button start system. This eliminates the need for pull cords, making it easier for anyone to get started quickly. The unit boasts an ergonomic design that includes a comfortable handle and the option for folding handles, making storage and transport simple.

In terms of functionality, the Briggs & Stratton 2550 PSI model is equipped with a 2.0-gallon per minute (GPM) water flow rate, allowing for effective cleaning without excessive water usage. The unit comes with a variety of nozzle options, providing different spray patterns to suit various tasks. The quick-connect nozzle system makes switching between nozzles easy and efficient.

Another key characteristic of this pressure washer is its rugged frame and all-terrain wheels, which ensure stability and maneuverability during operation. The wheels are designed to withstand various surfaces, allowing users to roll the machine over grass, gravel, or smooth pavement with ease.

Furthermore, the Briggs & Stratton 2550 PSI pressure washer features a built-in detergent tank that simplifies the process of applying soap while cleaning. This tank is easy to fill and ensures that users can tackle tougher cleaning jobs without the hassle of additional equipment.

With its combination of power, efficiency, and user-friendly design, the Briggs & Stratton 2550 PSI pressure washer stands out in the market as a reliable tool for homeowners and outdoor cleaning enthusiasts alike. Its blend of innovative features and practicality makes it an excellent choice for achieving professional-quality cleaning results.
Top Page Image Contents