Briggs & Stratton 2550 PSI manual Pressure Washer Rinsing, Cleaning Detergent Siphoning Tube

Page 17

5.Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump. Turn on water.

NOTICE

You must attach all hoses before you start the engine.

•Starting the engine without all the hoses connected and without the water turned ON will damage the pump.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

6.Start engine following instructions How to Start Your Pressure Washer.

7.Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes.

8.Allow detergent to "soak in" for 3-5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking).

IMPORTANT: You must flush the detergent siphoning system after each use by placing the filter into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes.

Pressure Washer Rinsing

For Rinsing:

1.Remove black detergent nozzle from nozzle extension.

2.Select and install desired high pressure nozzle following instructions How to Use Project Pro® Nozzles.

3.Keep spray gun a safe distance from area you plan to spray.

WARNING

Kickback from spray gun can cause you to fall.

•Operate pressure washer from a stable surface.

•Be extremely careful if you must use the pressure washer from a ladder, scaffolding, or any other similar location.

•Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when spray gun kicks back.

4.Apply a high pressure spray to a small area and then check surface for damage. If no damage is found, you can assume it is okay to continue rinsing.

5.Start at top of area to be rinsed, working down with same overlapping strokes as you used for cleaning.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it with clean water before stopping the engine.

1.Place detergent siphoning tube/filter in a bucket full of clean water.

2.Remove high pressure nozzle from nozzle extension.

3.Select and install black detergent nozzle following instructions How to Use Project Pro® Nozzles.

4.Flush for 1-2 minutes.

5.Shut off engine following instructions How to Stop Pressure Washer and turn off water supply.

6.ALWAYS point gun in a safe direction, press red button and squeeze spray gun trigger to release retained high water pressure.

IMPORTANT: Spray gun traps high water pressure, even when engine is stopped and water is disconnected.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury.

•Keep high pressure hose connected to pump and spray gun while system is pressurized.

•After each starting attempt, where engine fails to run, always point spray gun in safe direction, press red button and squeeze spray gun trigger to release high pressure.

Automatic Cool Down System (Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach temperatures above 125°F. The system engages to cool the pump by discharging the warm water onto the ground.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operator’s Manual Pressure Washer Where to Find UsEngine Date PurchasedTable of Contents Safety Rules Operator SafetyHazard Symbols and Meanings Equipment DescriptionWhen Adding or Draining Fuel Unintentional sparking can result in fire or electric shock Broken bones, fractures, bruises, or sprains could resultContact with muffler area can result in serious burns High pressure spray may damage fragile items including glass Risk of eye injury Spray can splash back or propel objectsAttach Handle and Accessory Tray AssemblyUnpack Pressure Washer Items in the carton includeAdd Fuel Add Engine OilFuel must meet these requirements High AltitudeConnect Hose and Water Supply to Pump Checklist Before Starting EngineFeatures and Controls Clearances and Air Movement OperationPressure Washer Location How to Start Your Pressure Washer How to Stop Your Pressure Washer Follow these instructions to change Project Pro nozzles How to Use Accessory TrayHow to Use Project Pro Nozzles To apply detergent, follow these steps Cleaning and Applying DetergentUsage Tips Pressure Washer Rinsing Cleaning Detergent Siphoning TubeAutomatic Cool Down System Thermal Relief For RinsingPressure Washer Maintenance MaintenanceMaintenance Schedule Ring Maintenance Nozzle MaintenanceCheck High Pressure Hose Check Detergent Siphoning TubeOil Oil Recommendations Engine MaintenanceChecking Oil Level Adding Engine OilTo service the air cleaner, follow these steps Service Air CleanerService Spark Plug Install spark plug and tighten firmlyKeep areas within heavy line clear of debris After Each UseAir Cooling System Long Term Storage Winter StorageProblem Cause Correction TroubleshootingWarranties Emissions Control System WarrantyOwner’s Warranty Responsibilities Claims and Coverage Exclusions MaintenanceEmission Information Limited Warranty 800 Product SpecificationsCommon Service Parts Manual del Operario Limpiadora a Presión Dónde encontrarnosMotor Fecha de compraSeguridad de Operario Resolución de problemas GarantíasMontaje Características y mandos OperandoReglas de seguridad Seguridad de OperarioDerscripción del equipo Opere el limpiadora a presión Solamente al aire libre Riesgo de electrocuciónCuando Pruebe LA Bujía DEL Motor Aviso Desembale la limpiadora a presión MontajeConecte el manubrio y bandeja accesoria Los artículos que se encuentran en la caja sonAgregue combustible Agregar aceite al motorEl combustible debe reunir los siguientes requisitos Gran altitudProporcione el suministro de agua adecuado Conecte la manguera y el suministro de agua a la bombaLista de revision previa al arranque del motor Bomba Desarrolla alta presión de agua Características y mandosUbicación del limpiadora a presión OperandoCómo darle arranque a su máquina limpiadora a presión Espacio libre alrededor del limpiadora a presiónAdvertencia Cómo detener su máquina limpiadora a presión Utilización de la bandeja de accesoriosLa Presión Baja Cómo usar las boquillas Project ProLa Presión Alta Para cambiar las boquillas de Project ProEnjuage de la máquina limpiadora a presión Limpieza y aplicación del detergenteUso inclina Para aplicar el detergente, siga los siguientes pasosSistema de enfriamiento automático alivio térmico Limpieza del tubo de inyección de detergenteMantenimiento de la limpiadora a presión MantenimientoPlan de mantenimiento Revise la manguera de alta presión Revise y limpie el colador de entradaChequee el tubo de sifón del detergente Revise la pistolaMantenimiento de los anillos o Mantenimiento del motorComprobación del nivel de aceite Aceite Recomendaciones sobre el aceiteAfloje el tornillo a y quite la cubierta B Cambio de aceite del motorServicio del depurador de aire Servicio del bujíaServicio del apagachispas Despues de cada usoSistema de refrigeración de aire BRIGGSandSTRATTON.COMAlmacenamiento prolongado Almacenamiento para inviernoProblema Causa Solución Resolución de problemasGarantía del sistema de control de emisiones GarantíasResponsabilidades de la garantía del propietario Operaciones de mantenimiento que se enumeran en lasInformación sobre emisiones Garantía Limitada Temperatura del suministro Especificaciones del productoServicio común despide

2550 PSI specifications

The Briggs & Stratton 2550 PSI pressure washer is a powerful cleaning tool designed to tackle a variety of outdoor tasks with ease. With a maximum cleaning power of 2550 PSI, this machine is well-equipped for efficiently removing dirt, grime, and stubborn stains from surfaces such as driveways, patios, decks, and vehicles.

One of the standout features of the Briggs & Stratton 2550 PSI pressure washer is its durable and reliable engine. Powered by a Briggs & Stratton 550 Series engine, it delivers consistent performance and dependable starts, allowing users to get to work without the frustration of engine failure. This engine is designed with an overhead valve (OHV) configuration, which increases efficiency while reducing emissions.

The pressure washer is also user-friendly, featuring a convenient push-button start system. This eliminates the need for pull cords, making it easier for anyone to get started quickly. The unit boasts an ergonomic design that includes a comfortable handle and the option for folding handles, making storage and transport simple.

In terms of functionality, the Briggs & Stratton 2550 PSI model is equipped with a 2.0-gallon per minute (GPM) water flow rate, allowing for effective cleaning without excessive water usage. The unit comes with a variety of nozzle options, providing different spray patterns to suit various tasks. The quick-connect nozzle system makes switching between nozzles easy and efficient.

Another key characteristic of this pressure washer is its rugged frame and all-terrain wheels, which ensure stability and maneuverability during operation. The wheels are designed to withstand various surfaces, allowing users to roll the machine over grass, gravel, or smooth pavement with ease.

Furthermore, the Briggs & Stratton 2550 PSI pressure washer features a built-in detergent tank that simplifies the process of applying soap while cleaning. This tank is easy to fill and ensures that users can tackle tougher cleaning jobs without the hassle of additional equipment.

With its combination of power, efficiency, and user-friendly design, the Briggs & Stratton 2550 PSI pressure washer stands out in the market as a reliable tool for homeowners and outdoor cleaning enthusiasts alike. Its blend of innovative features and practicality makes it an excellent choice for achieving professional-quality cleaning results.
Top Page Image Contents