Briggs & Stratton 2550 PSI Service Air Cleaner, To service the air cleaner, follow these steps

Page 21

Change oil while engine is still warm from running, as follows:

1.Drain fuel tank by running pressure washer until fuel tank is empty.

2.Disconnect spark plug wire and keep it away from spark plug.

3.Clean area around oil fill, remove oil fill cap/dipstick. Wipe dipstick clean.

4.Tip your pressure washer to drain oil from oil fill into a suitable container making sure you tip your unit away from spark plug. When crankcase is empty, return pressure washer to upright position.

5.Slowly pour recommended oil (about 20 oz.) into oil fill opening. Pause to permit oil to settle. Fill to “Full” mark on dipstick.

6.Wipe dipstick clean each time oil level is checked. DO NOT overfill.

7.Replace and tighten dipstick.

8.Wipe up any remaining oil.

9.Reconnect spark plug wire to spark plug.

Service Air Cleaner

Your engine will not run properly and may be damaged if you run it with a dirty air cleaner.

Service the air cleaner once every 25 hours of operation or once each year, whichever comes first. Service more often if operating under dirty or dusty conditions.

To service the air cleaner, follow these steps:

1. Loosen screw (A) and tilt cover (B) down.

D

C

E

A B

2.Carefully remove cartridge (C) assembly.

3.To clean cartridge, gently tap pleated paper side on a flat surface.

4.Reinstall clean or new cartridge assembly inside cover.

5.Insert cover’s tabs (D) into slots in bottom of base (E).

6.Tilt cover up and tighten screw securely to base.

Service Spark Plug

Change the spark plug every 100 hours of operation or once each year, whichever comes first. This will help your engine to start easier and run better.

1.Clean area around spark plug.

2.Remove and inspect spark plug.

3.Check electrode gap with wire feeler gauge and set spark plug gap to 0.030 inch (0.76 mm) if necessary.

4.Replace spark plug if electrodes are pitted, burned or porcelain is cracked. Use the recommended replacement plug. See Specifications.

5.Install spark plug and tighten firmly.

Spark Arrester Service

Your engine is not factory-equipped with a spark arrester. In some areas, it is illegal to operate an engine without a spark arrester. Check local laws and regulations. A spark arrester is available from your nearest qualified service center.The spark arrester must be serviced every 50 hours to keep it functioning as designed.

If the engine has been running, the muffler will be very hot. Allow the muffler to cool before servicing spark arrester.

WARNING

Contact with muffler area can result in serious burns.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•DO NOT touch hot parts and AVOID hot exhaust gases.

•Allow equipment to cool before touching.

•Keep at least 5 feet (1.5 m) of clearance on all sides of pressure washer including overhead.

•Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

•Remove spark arrester screen for cleaning and inspection.

•Replace if screen is damaged.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operator’s Manual Pressure Washer Where to Find UsEngine Date PurchasedTable of Contents Safety Rules Operator SafetyHazard Symbols and Meanings Equipment DescriptionWhen Adding or Draining Fuel Broken bones, fractures, bruises, or sprains could result Contact with muffler area can result in serious burnsUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Risk of eye injury Spray can splash back or propel objectsAttach Handle and Accessory Tray AssemblyUnpack Pressure Washer Items in the carton includeAdd Fuel Add Engine OilFuel must meet these requirements High AltitudeConnect Hose and Water Supply to Pump Checklist Before Starting EngineFeatures and Controls Operation Pressure Washer LocationClearances and Air Movement How to Start Your Pressure Washer How to Stop Your Pressure Washer How to Use Accessory Tray How to Use Project Pro NozzlesFollow these instructions to change Project Pro nozzles Cleaning and Applying Detergent Usage TipsTo apply detergent, follow these steps Pressure Washer Rinsing Cleaning Detergent Siphoning TubeAutomatic Cool Down System Thermal Relief For RinsingMaintenance Maintenance SchedulePressure Washer Maintenance Ring Maintenance Nozzle MaintenanceCheck High Pressure Hose Check Detergent Siphoning TubeOil Oil Recommendations Engine MaintenanceChecking Oil Level Adding Engine OilTo service the air cleaner, follow these steps Service Air CleanerService Spark Plug Install spark plug and tighten firmlyAfter Each Use Air Cooling SystemKeep areas within heavy line clear of debris Long Term Storage Winter StorageProblem Cause Correction TroubleshootingEmissions Control System Warranty Owner’s Warranty ResponsibilitiesWarranties Maintenance Emission InformationClaims and Coverage Exclusions Limited Warranty Product Specifications Common Service Parts800 Manual del Operario Limpiadora a Presión Dónde encontrarnosMotor Fecha de compraSeguridad de Operario Resolución de problemas GarantíasMontaje Características y mandos OperandoSeguridad de Operario Derscripción del equipoReglas de seguridad Opere el limpiadora a presión Solamente al aire libre Riesgo de electrocuciónCuando Pruebe LA Bujía DEL Motor Aviso Desembale la limpiadora a presión MontajeConecte el manubrio y bandeja accesoria Los artículos que se encuentran en la caja sonAgregue combustible Agregar aceite al motorEl combustible debe reunir los siguientes requisitos Gran altitudConecte la manguera y el suministro de agua a la bomba Lista de revision previa al arranque del motorProporcione el suministro de agua adecuado Bomba Desarrolla alta presión de agua Características y mandosUbicación del limpiadora a presión OperandoCómo darle arranque a su máquina limpiadora a presión Espacio libre alrededor del limpiadora a presiónAdvertencia Cómo detener su máquina limpiadora a presión Utilización de la bandeja de accesoriosLa Presión Baja Cómo usar las boquillas Project ProLa Presión Alta Para cambiar las boquillas de Project ProEnjuage de la máquina limpiadora a presión Limpieza y aplicación del detergenteUso inclina Para aplicar el detergente, siga los siguientes pasosSistema de enfriamiento automático alivio térmico Limpieza del tubo de inyección de detergenteMantenimiento Plan de mantenimientoMantenimiento de la limpiadora a presión Revise la manguera de alta presión Revise y limpie el colador de entradaChequee el tubo de sifón del detergente Revise la pistolaMantenimiento de los anillos o Mantenimiento del motorComprobación del nivel de aceite Aceite Recomendaciones sobre el aceiteAfloje el tornillo a y quite la cubierta B Cambio de aceite del motorServicio del depurador de aire Servicio del bujíaServicio del apagachispas Despues de cada usoSistema de refrigeración de aire BRIGGSandSTRATTON.COMAlmacenamiento prolongado Almacenamiento para inviernoProblema Causa Solución Resolución de problemasGarantía del sistema de control de emisiones GarantíasResponsabilidades de la garantía del propietario Operaciones de mantenimiento que se enumeran en lasInformación sobre emisiones Garantía Limitada Especificaciones del producto Servicio común despideTemperatura del suministro

2550 PSI specifications

The Briggs & Stratton 2550 PSI pressure washer is a powerful cleaning tool designed to tackle a variety of outdoor tasks with ease. With a maximum cleaning power of 2550 PSI, this machine is well-equipped for efficiently removing dirt, grime, and stubborn stains from surfaces such as driveways, patios, decks, and vehicles.

One of the standout features of the Briggs & Stratton 2550 PSI pressure washer is its durable and reliable engine. Powered by a Briggs & Stratton 550 Series engine, it delivers consistent performance and dependable starts, allowing users to get to work without the frustration of engine failure. This engine is designed with an overhead valve (OHV) configuration, which increases efficiency while reducing emissions.

The pressure washer is also user-friendly, featuring a convenient push-button start system. This eliminates the need for pull cords, making it easier for anyone to get started quickly. The unit boasts an ergonomic design that includes a comfortable handle and the option for folding handles, making storage and transport simple.

In terms of functionality, the Briggs & Stratton 2550 PSI model is equipped with a 2.0-gallon per minute (GPM) water flow rate, allowing for effective cleaning without excessive water usage. The unit comes with a variety of nozzle options, providing different spray patterns to suit various tasks. The quick-connect nozzle system makes switching between nozzles easy and efficient.

Another key characteristic of this pressure washer is its rugged frame and all-terrain wheels, which ensure stability and maneuverability during operation. The wheels are designed to withstand various surfaces, allowing users to roll the machine over grass, gravel, or smooth pavement with ease.

Furthermore, the Briggs & Stratton 2550 PSI pressure washer features a built-in detergent tank that simplifies the process of applying soap while cleaning. This tank is easy to fill and ensures that users can tackle tougher cleaning jobs without the hassle of additional equipment.

With its combination of power, efficiency, and user-friendly design, the Briggs & Stratton 2550 PSI pressure washer stands out in the market as a reliable tool for homeowners and outdoor cleaning enthusiasts alike. Its blend of innovative features and practicality makes it an excellent choice for achieving professional-quality cleaning results.
Top Page Image Contents