Briggs & Stratton 2550 PSI manual Check High Pressure Hose, Check Detergent Siphoning Tube

Page 19

Check High Pressure Hose

The high pressure hose can develop leaks from wear, kinking, or abuse. Inspect the hose each time before using it. Check for cuts, leaks, abrasions or bulging of cover, damage or movement of couplings. If any of these conditions exist, replace the hose immediately.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

NEVER repair high pressure hose. Replace it.

Replacement hose rating MUST exceed maximum pressure rating of unit.

Check Detergent Siphoning Tube

Examine the filter on the detergent tube and clean if clogged. The tube should fit tightly on the barbed fitting. Examine the tube for leaks or tears. Replace the filter or tube if either is damaged.

Check Spray Gun

Examine the hose connection to the spray gun and make sure it is secure. Test the trigger by pressing the red button and making sure the trigger “springs back” into place when you release it. You should not be able to press the trigger without pressing the red button. Replace spray gun immediately if it fails any of these tests.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure. The principal cause of excessive pump pressure is a nozzle clogged or restricted with foreign materials, such as dirt, etc. To correct the problem, immediately clean the nozzle following these instructions:

1.Shut off engine and turn off water supply.

2.ALWAYS point spray gun in a safe direction, press red button and squeeze spray gun trigger to release retained high water pressure.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury.

Keep high pressure hose connected to pump and spray gun while system is pressurized.

After each starting attempt, where engine fails to run, always point spray gun in safe direction, press red button and squeeze spray gun trigger to release high pressure.

3.Remove nozzle from end of nozzle extension.

4.Use a small paper clip to free any foreign material clogging or restricting nozzle (A).

A

5.Remove nozzle extension from spray gun.

6.Using a garden hose, remove additional debris by back flushing water through nozzle extension. Back flush between 30 to 60 seconds.

7.Reinstall nozzle and in-line filter into nozzle extension.

8.Reconnect nozzle extension to spray gun.

9.Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump. Turn on water.

10.Start engine following instructions How to Start Your Pressure Washer.

11.Test pressure washer by operating with each quick connect nozzle.

O-Ring Maintenance

Purchase an O-Ring/Maintenance Kit, model 6048, by contacting the nearest authorized service center. It is not included with the pressure washer. This kit includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service your unit’s o-rings.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.

19

Image 19
Contents Operator’s Manual Date Purchased Where to Find UsPressure Washer EngineTable of Contents Equipment Description Operator SafetySafety Rules Hazard Symbols and MeaningsWhen Adding or Draining Fuel Contact with muffler area can result in serious burns Broken bones, fractures, bruises, or sprains could resultUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Risk of eye injury Spray can splash back or propel objectsItems in the carton include AssemblyAttach Handle and Accessory Tray Unpack Pressure WasherHigh Altitude Add Engine OilAdd Fuel Fuel must meet these requirementsConnect Hose and Water Supply to Pump Checklist Before Starting EngineFeatures and Controls Pressure Washer Location OperationClearances and Air Movement How to Start Your Pressure Washer How to Stop Your Pressure Washer How to Use Project Pro Nozzles How to Use Accessory TrayFollow these instructions to change Project Pro nozzles Usage Tips Cleaning and Applying DetergentTo apply detergent, follow these steps For Rinsing Cleaning Detergent Siphoning TubePressure Washer Rinsing Automatic Cool Down System Thermal ReliefMaintenance Schedule MaintenancePressure Washer Maintenance Check Detergent Siphoning Tube Nozzle MaintenanceRing Maintenance Check High Pressure HoseAdding Engine Oil Engine MaintenanceOil Oil Recommendations Checking Oil LevelInstall spark plug and tighten firmly Service Air CleanerTo service the air cleaner, follow these steps Service Spark PlugAir Cooling System After Each UseKeep areas within heavy line clear of debris Long Term Storage Winter StorageProblem Cause Correction TroubleshootingOwner’s Warranty Responsibilities Emissions Control System WarrantyWarranties Emission Information MaintenanceClaims and Coverage Exclusions Limited Warranty Common Service Parts Product Specifications800 Manual del Operario Fecha de compra Dónde encontrarnosLimpiadora a Presión MotorCaracterísticas y mandos Operando Resolución de problemas GarantíasSeguridad de Operario MontajeDerscripción del equipo Seguridad de OperarioReglas de seguridad Opere el limpiadora a presión Solamente al aire libre Riesgo de electrocuciónCuando Pruebe LA Bujía DEL Motor Aviso Los artículos que se encuentran en la caja son MontajeDesembale la limpiadora a presión Conecte el manubrio y bandeja accesoriaGran altitud Agregar aceite al motorAgregue combustible El combustible debe reunir los siguientes requisitosLista de revision previa al arranque del motor Conecte la manguera y el suministro de agua a la bombaProporcione el suministro de agua adecuado Bomba Desarrolla alta presión de agua Características y mandosEspacio libre alrededor del limpiadora a presión OperandoUbicación del limpiadora a presión Cómo darle arranque a su máquina limpiadora a presiónAdvertencia Cómo detener su máquina limpiadora a presión Utilización de la bandeja de accesoriosPara cambiar las boquillas de Project Pro Cómo usar las boquillas Project ProLa Presión Baja La Presión AltaPara aplicar el detergente, siga los siguientes pasos Limpieza y aplicación del detergenteEnjuage de la máquina limpiadora a presión Uso inclinaSistema de enfriamiento automático alivio térmico Limpieza del tubo de inyección de detergentePlan de mantenimiento MantenimientoMantenimiento de la limpiadora a presión Revise la pistola Revise y limpie el colador de entradaRevise la manguera de alta presión Chequee el tubo de sifón del detergenteAceite Recomendaciones sobre el aceite Mantenimiento del motorMantenimiento de los anillos o Comprobación del nivel de aceiteServicio del bujía Cambio de aceite del motorAfloje el tornillo a y quite la cubierta B Servicio del depurador de aireBRIGGSandSTRATTON.COM Despues de cada usoServicio del apagachispas Sistema de refrigeración de aireAlmacenamiento prolongado Almacenamiento para inviernoProblema Causa Solución Resolución de problemasOperaciones de mantenimiento que se enumeran en las GarantíasGarantía del sistema de control de emisiones Responsabilidades de la garantía del propietarioInformación sobre emisiones Garantía Limitada Servicio común despide Especificaciones del productoTemperatura del suministro

2550 PSI specifications

The Briggs & Stratton 2550 PSI pressure washer is a powerful cleaning tool designed to tackle a variety of outdoor tasks with ease. With a maximum cleaning power of 2550 PSI, this machine is well-equipped for efficiently removing dirt, grime, and stubborn stains from surfaces such as driveways, patios, decks, and vehicles.

One of the standout features of the Briggs & Stratton 2550 PSI pressure washer is its durable and reliable engine. Powered by a Briggs & Stratton 550 Series engine, it delivers consistent performance and dependable starts, allowing users to get to work without the frustration of engine failure. This engine is designed with an overhead valve (OHV) configuration, which increases efficiency while reducing emissions.

The pressure washer is also user-friendly, featuring a convenient push-button start system. This eliminates the need for pull cords, making it easier for anyone to get started quickly. The unit boasts an ergonomic design that includes a comfortable handle and the option for folding handles, making storage and transport simple.

In terms of functionality, the Briggs & Stratton 2550 PSI model is equipped with a 2.0-gallon per minute (GPM) water flow rate, allowing for effective cleaning without excessive water usage. The unit comes with a variety of nozzle options, providing different spray patterns to suit various tasks. The quick-connect nozzle system makes switching between nozzles easy and efficient.

Another key characteristic of this pressure washer is its rugged frame and all-terrain wheels, which ensure stability and maneuverability during operation. The wheels are designed to withstand various surfaces, allowing users to roll the machine over grass, gravel, or smooth pavement with ease.

Furthermore, the Briggs & Stratton 2550 PSI pressure washer features a built-in detergent tank that simplifies the process of applying soap while cleaning. This tank is easy to fill and ensures that users can tackle tougher cleaning jobs without the hassle of additional equipment.

With its combination of power, efficiency, and user-friendly design, the Briggs & Stratton 2550 PSI pressure washer stands out in the market as a reliable tool for homeowners and outdoor cleaning enthusiasts alike. Its blend of innovative features and practicality makes it an excellent choice for achieving professional-quality cleaning results.