Briggs & Stratton 01937 How to Use the Hose Reel, Pressure Washer Rinsing, Thermal Relief

Page 11

2800 PSI Pressure Washer

8.Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes.

9.Allow detergent to soak in between 3–5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking).

How to Use the Hose Reel

Your pressure washer is equipped with a hose reel designed to store the hose when unit is not in use. See “Prepare Unit for Storage” for long term storage of more than 30 days.

After each use:

1.Disconnect hose from spray gun and high pressure outlet on pump.

Pressure Washer Rinsing

After detergent is applied, scour the surface and rinse it clean as follows:

1.Apply safety latch to spray gun.

2.Make sure both chemical shut-off valves are in “Off” position.

3.Remove black chemical spray tip from nozzle extension.

4.Select and install desired high pressure spray tip, as described in “How to Use Spray Tips”.

5.Keep spray gun a safe distance from spray surface.

WARNING

High pressure spray could cause you to fall if you are too close to the cleaning surface.

•Keep spray nozzle between 8 to 24 inches away from cleaning surface.

•Operate this unit on a stable surface.

•Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location.

•Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back.

6.Apply a high pressure spray to a small area and then check the surface for damage. If no damage, proceed to step 7.

7.Start at top of area to be rinsed, working down with same overlapping strokes used for cleaning.

2.Drain water from hose.

3.Slide one end of hose into hole on hose reel.Turn hose reel with handle to coil hose onto reel (Figure 14).

Figure 14 — Install Hose on Hose Reel

IMPORTANT: DO NOT use your pressure washer with the hose coiled onto the hose reel.The hose reel is for storage purposes only.

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach temperatures above 125°F.The system engages to cool the pump by

discharging the warm water onto the ground.

11

Image 11

Contents 01937 2800 PSI Equipment Description Table of ContentsSafety Rules When Adding or Draining Fuel High pressure spray may damage fragile items including glass Recoil Starter Safety Goggles not shown Always use the enclosedKnow Your Pressure Washer Choke LeverRemove Pressure Washer From Carton AssemblyCarton Contents Preparing Pressure Washer for USEAdd Engine Oil and Fuel Attach Hose ReelAttach Chemical Reservoirs Screen, do Checklist Before Starting EngineConnect Hose and Water Supply to Pump Inspect inletTo Start Your Pressure Washer HOW to USE PressureHow to Stop Your Pressure Washer WasherHigh Pressure How to Use Spray TipsCleaning and Applying Chemical Low PressureThermal Relief How to Use the Hose ReelPressure Washer Rinsing Automatic Cool Down SystemPressure Washer Maintenance SpecificationsGeneral Maintenance Recommendations To remove air from the pump, follow these steps Nozzle MaintenanceRing Maintenance Purge Pump of Air ContaminantsStoring the Engine Engine MaintenanceAlways wear eye protection when using PumpSaver Preparing Unit for StorageProblem Cause Correction TroubleshootingItems Not Illustrated Description Exploded View and Parts List UnitDescription Exploded View and Parts List Pump PSI Pressure Washer Year Consumer Use Years Years orAdvertencia Tabla DE ContenidosDescripción DEL Equipo Instrucciones DE SeguridadCuando Añada Combustible O Vacíe EL Depósito PeligroPrecaución Perilla del Cebador Usada para arranque de motores fríos Conozca SU Maquina Lavadora DE PresionToma de Alta Presión Entrada de Agua Entrada de Agua Conexión para la manguera de jardínContenido de la Caja MontajePreparando EL Lavador a Presión Para SU USO Remueva el Lavador a Presión del EmpaqueGancho del Pistola Montaje del Carretel de MangueraMontaje de Depósitos de Productos Químicos Agregar Aceite al Motor y GasolinaProporcione el suministro de agua adecuado Conecte la Manguera y el Suministro de Agua a la BombaLista de Revision Previa al Arranque del Motor Deposite la gasolina adecuada en el tanque del combustibleCómo Detener su Lavadora a Presión Cómo Usar SU Lavadora a PresiónCómo Darle Arranque a su Lavadora a Presión Limpieza y Aplicación del Químico Cómo Usar las Puntas de RociadoLa Presión Baja La Presión AltaColoque el cerrojo de seguridad a la pistola de rociado Enjuage de la Máquina Lavadora a PresiónCómo Usar el Carrete de la Manguera Sistema de Enfriamiento Automático Alivio TérmicoMantenimiento DE LA Lavadora a Presion EspecificacionesRecomendaciones Generales Antes de Cada UsoMantenimiento de los Anillos O Mantenimiento DEL MotorElimine el Aire y los Contaminantes de la Bomba Mantenimiento de la BoquillaAlmacene la unidad en un lugar limpio y seco Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Proteger la BombaNotas Notas Reparacion DE Daños Garantía Limitada