Pentair 100 Ventilation, Outdoor Installation only, Outdoor Vent CAP Installation

Page 17

Installation (contd.)

17

VENTILATION

OUTDOOR INSTALLATION ONLY

(See additional instructions for outdoor Power- Max units in PowerMax Appendix)

For outdoor installation with built in vent top, the heater must be placed in a suitable area on a level, noncombus- tible surface. Do not install the heater under an overhang with clearances less than 3 feet from the top of the heater. The area under an overhang must be open on three sides.

IMPORTANT!

In an outdoor installation it is important to protect your heater from water damage. Ensure water is diverted from overhanging eves with a proper gutter/ drainage system. The heater must be set on a level foundation for proper rain drainage.

Maintain minimum clearances as indicated below. Install a minimum of 4 feet below, and 4 feet horizontally from any opening to a building.

The heater should not be installed closer than 6 inches to any fences, walls or shrubs at any side or back, nor closer than 18 inches at the plumbing side. A minimum clearance of 24 inches must be maintained at the front of the heater.

 

6"

DOOR

6"

 

24"

 

 

18"

Figure 18.

IMPORTANT!

When locating the heater, consider that high winds can roll over or deflect off adjacent buildings and walls. Normally, placing the heater at least three feet from any wall will minimize downdraft.

Unusually high prevailing wind conditions and downdrafts may require the use of a stack type outdoor vent kit (available at additional cost).

NOTE

This unit shall not be operated outdoors at temperatures below 0o F. for propane and -20oF. for natural gas.

STACK TYPE OUTDOOR VENT KIT

Model

Vent Cap

Product No.

Vent Dia.

 

150

OV15

460237

6 in.

 

195/200

OV20

460222

7 in.

 

250

OV25

460223

7 in.

 

300

OV30

460224

8 in.

 

350

OV35

460225

9 in.

 

400

OV40

460226

10 in.

Table 9.

 

 

 

 

 

Outdoor Stack

 

 

Top Cover

Flue Adaptor

Inner Panel

Flue Collector

Figure 19.

Figure 20.

OUTDOOR VENT CAP INSTALLATION

The MiniMax Plus heater is shipped standard as an outdoor stackless unit. To install the outdoor vent kit:

1.Take out the louvered outer top after first removing all 1/4 in. sheet metal screws attaching it along its perimeter to the cabinet. Set it aside.

2.Place the flue adaptor over the flue collector opening. Temporarily, put the top cover, from the kit, on with the label to the front of the heater. Center the flue adaptor evenly inside the top cover flue stack opening. Remove the top cover and secure the centered flue adaptor to the inner panel with the provided #8 x 1/2 in. drill qwik screws.

3.Place the top cover, with the hole for the stack, on the heater cabinet.

4.Install the vent stack through the hole in the top cover, over the flue adaptor top ring.

5.Using a 3/32 in. drill bit, position the “L” bracket to hold the top cover and outdoor stack. Drill the pilot holes through the “L” bracket holes to accept the screws.

6.Secure the vent stack and the inner top with the #8

x1/4 in. sheet metal screws through the “L” brackets.

Rev. G 1-22-04

P/N 471048

Image 17
Contents For additional free copies of this manual call 800 For Your Safety Read Before OperatingWhat to do if YOU Smell GAS Table of Contents Important Notices Code RequirementsOperation contd Warranty InformationSafety Rules To Turn OFF GAS to Appliance For Your Safety Read Before LightingOperating Instructions Minimax Plus Electronic Ignition LIGHTING/OPERATION Propane Safety LockoutWhat to do if YOU Smell GAS Lighting InstructionsOperating Controls Indicator Light DescriptionHeat Heat Troubleshooting ControlsTroubleshooting Controls Energy Saving Tips Maintenance InstructionsSpring and Fall Operation Winter OperationPool and SPA Water Chemical BalanceIf pH becomes too high over alkaline, it has these effects Alkalinity High LowSpecifications Installation InstructionsPlumbing Connections Water ConnectionsPlumbing For 1½ & 2 in. Copper Pipe QUICK-FLANGE Installation InstructionsGAS Connections GAS Line InstallationsVentilation Outdoor Installation onlyOutdoor Vent CAP Installation Front Stack Type Indoor Draft Hood KIT MiniMax heaters, including PowerMax versionsTransformer Wiring Instruction Indoor Draft Hood InstallationIgnition Wiring Diagram MiniMax Plus Electronic Installation contdWire Remote MiniMax Plus Millivolt Wiring DiagramHeater Short Cycling Rapid On and Off Operation Heater exchanger scaledMinimax Plus Heater ALL Models Description QTY MiniMax Plus Only Parts ListDescription QTY MiniMax Plus Only Parts List, contdPowerMax Pool & Spa Heater Code Requirements General SpecificationIntroduction Mounting Assembly Venting Indoor Installations Powermax Venting Guidelines Outdoor Installation Powermax Venting Guidelines 22-04 Rev. G Wiring Diagram for Powermax KIT Powermax Heater ALL Models Description QTY PowerMax Heater Only Parts ListDescription QTY PowerMax Heater Only Parts List, contdPowerMax Assembly PowerMax Assembly Parts ListPentair Pool Products, Inc
Related manuals
Manual 36 pages 41.25 Kb

100 specifications

Pentair 100 is an advanced water filtration system designed to address a variety of water purification needs for residential and commercial applications. Renowned for its efficiency and reliability, the Pentair 100 incorporates cutting-edge technologies that enhance the quality of water while ensuring ease of use.

One of the standout features of the Pentair 100 is its multi-stage filtration process. This system utilizes a combination of sediment filters, activated carbon filters, and advanced membrane technology to remove impurities including bacteria, viruses, heavy metals, and chlorine. The sediment filter captures larger particles, while the activated carbon filter removes organic compounds and improves taste and odor. The membrane technology employed in the system further refines the water by filtering out microscopic contaminants, ensuring purity.

The Pentair 100 is equipped with an innovative monitoring system that allows users to track filter performance and maintenance needs in real time. This feature is designed to optimize the lifespan of the filters and ensure that the system operates at maximum efficiency. Additionally, the intuitive LED indicators provide clear notifications regarding filter replacements and system status, simplifying the upkeep of the filtration unit.

Sustainability is another core aspect of the Pentair 100. The system is designed to reduce water wastage, making it an environmentally friendly option for consumers. Its efficient filtration process minimizes the need for bottled water, contributing to reduced plastic waste. Furthermore, the materials used in the construction of the unit are durable and recyclable, aligning with contemporary green initiatives.

The compact design of the Pentair 100 makes it suitable for various setups, whether it is for a small apartment or a larger commercial space. Installation is straightforward, with flexible options for under-sink or point-of-use configurations. This versatility extends to its compatibility with existing plumbing systems, allowing for seamless integration.

In summary, the Pentair 100 embodies advanced filtration technologies, sustainable operations, and user-friendly features, making it an excellent choice for anyone looking to improve their water quality. Its robust performance, combined with smart monitoring capabilities, ensures that users have access to safe and delicious water while promoting environmental responsibility. Whether for everyday use or special needs, the Pentair 100 stands out as a premier solution in the water filtration market.