Lighting Instructions, What to do if YOU Smell GAS

Figure 5.

Figure 6.

Operation (contd.)

MINIMAX PLUS MILLIVOLT LIGHTING/OPERATION-NATURAL GAS & PROPANE

FOR YOUR SAFETY: READ BEFORE LIGHTING

WARNING

If you do not follow these instructions exactly, a fire or explosion may result causing personal injury, loss of life and property damage.

Since propane gas is heavier than air, escaping propane will accumulate and remain at ground level. Do not attempt to light the heater. If you suspect a propane leak, lighting the heater can result in a fire or explosion which can cause personal injury, death, and property damage.

A.This heater is equipped with a pilot which must be lighted manually. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the heater area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

-Do not try to light any heater.

-Do not touch any electrical switch; do not use any phone in your building.

-Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

-If you cannot reach your gas supplier, call the Fire Department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it. Call a qualified service technician. Forced or attempted repair may result in a fire or explosion.

D.Do not use this heater if any part has been under water. Immediately call a qualified service technician to inspect the heater and to replace any part of the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS

1.STOP! Read the safety information above.

2.Set the thermostat to the lowest setting.

3.Turn off electric power to the heater.

4.Push in gas control knob slightly and turn clock-

wise to “OFF”.

Robertshaw Millivolt Gas Valve	Honeywell Millivolt Gas Valve
Figure 3.	Figure 4.

Gas control knobs shown in “OFF” position.

7.Push the control knob all the way and hold in. Immediately light the pilot with Presslite matchless ignition system by pressing the red igniter button (located at the panel next to the gas valve). Continue to hold the control knob in for about one (1) minute after the pilot is lit. Release knob and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 4 through 7.

•If knob does not pop up when released, stop and immediately call your service technician or gas

supplier.

•If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier.

NOTE

Knob cannot be turned from “Pilot to “OFF”” unless knob is pushed in slightly. DO NOT FORCE.

5.Wait five (5) minutes to clear out any gas. If you then smell gas, STOP! Follow "B" in the safety informa- tion above. If you don't smell gas, go to the next step.

6.Push in gas control knob slightly and turn counter-

clockwise to “Pilot”.

8.Turn knob on gas control

counterclockwise to “ON”.

9.Replace the control access door.

10.Set the thermostat to the desired setting.

Pilot

TO TURN OFF GAS TO APPLIANCE

1.Set the thermostat to lowest setting.

2.Turn off all electric power to the heater if service is to be performed.

3.Remove control access door.

4.Push in gas control knob slightly and turn clockwise to "OFF". Do not force.

5.Replace control access door.

Rev. G 1-22-04

P/N 471048

100 specifications

Pentair 100 is an advanced water filtration system designed to address a variety of water purification needs for residential and commercial applications. Renowned for its efficiency and reliability, the Pentair 100 incorporates cutting-edge technologies that enhance the quality of water while ensuring ease of use.

One of the standout features of the Pentair 100 is its multi-stage filtration process. This system utilizes a combination of sediment filters, activated carbon filters, and advanced membrane technology to remove impurities including bacteria, viruses, heavy metals, and chlorine. The sediment filter captures larger particles, while the activated carbon filter removes organic compounds and improves taste and odor. The membrane technology employed in the system further refines the water by filtering out microscopic contaminants, ensuring purity.

The Pentair 100 is equipped with an innovative monitoring system that allows users to track filter performance and maintenance needs in real time. This feature is designed to optimize the lifespan of the filters and ensure that the system operates at maximum efficiency. Additionally, the intuitive LED indicators provide clear notifications regarding filter replacements and system status, simplifying the upkeep of the filtration unit.

Sustainability is another core aspect of the Pentair 100. The system is designed to reduce water wastage, making it an environmentally friendly option for consumers. Its efficient filtration process minimizes the need for bottled water, contributing to reduced plastic waste. Furthermore, the materials used in the construction of the unit are durable and recyclable, aligning with contemporary green initiatives.

The compact design of the Pentair 100 makes it suitable for various setups, whether it is for a small apartment or a larger commercial space. Installation is straightforward, with flexible options for under-sink or point-of-use configurations. This versatility extends to its compatibility with existing plumbing systems, allowing for seamless integration.

In summary, the Pentair 100 embodies advanced filtration technologies, sustainable operations, and user-friendly features, making it an excellent choice for anyone looking to improve their water quality. Its robust performance, combined with smart monitoring capabilities, ensures that users have access to safe and delicious water while promoting environmental responsibility. Whether for everyday use or special needs, the Pentair 100 stands out as a premier solution in the water filtration market.