Zenoah BC3401DL manual  13 , Recommended Mixing Ratio Gasoline 50OIL, HOW to MIX Fuel

Page 13

Fuel

WARNING

Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine.

The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE)

Do not use BIA or TCW (2-stroke water- cooling type) mixed oil.

RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1

(when using RedMax/ZENOAH genuine oil)

50:1 MIXING CHART

GASOLINE gal. 1 2 3 4 5

2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13

GASOLINE liter 1

2

3

4

5

2-CYCLE OIL ml 20 40 60 80 100

Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.

These engines are certified to operate on unleaded gasoline.

Make sure to use gasoline with a minimum octane number of 89 RON (USA/Canada: 87AL)

If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may consequently occur.

Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.

HOW TO MIX FUEL

IMPORTANT

Pay attention to agitation.

1.Measure out the quantities of gasoline and oil to be mixed.

2.Put some of the gasoline into a clean, approved fuel container.

3.Pour in all of the oil and agitate well.

4.Pour In the rest of gasoline and agitate

13

Image 13
Contents 848-G6D-93A2 BC3401DL BC4401DWSafety First Contents  4  SpecificationsBC3401DL BC4401DW 5  Emission control label 6  Safety PrecautionsWork gear and clothing  7 Avoid Noise Problem Things to check before using your brushcutter 8  Things to check before starting up the engine 9  Things to be careful about when using your brushcutter 10   11  Set Up 12  Installing Cutting HeadPutting on Waist PAD BC4401DW only HOW to MIX Fuel When using RedMax/ZENOAH genuine oilFuel  13 Fueling the Unit  14 For Your Engine LIFE, Avoid  15  OperationStarting Engine  16   17  Optional Blade UsageOPT3 OPT4 For BC3401DL OPT5 OPT6  18 Bracket Handle Cutting MethodOPT7 OPT8  19 Operation Controlling Blade Bounce  20 What causes blade thrust How you can reduce the chance of blade thrust 21  Maintenance BladeOPT9 How you can maintain the best control 22  MaintenanceRefilling Trimming Line AIR Filter 23  Storage Procedures to be Performed After Every 100 Hours of USEDisposal  24  25  Parts List 26  Drive Unit BC3401DL S/N 60200000 and up 27   28  Engine Unit BC3401DL S/N 60200000 and upDescription Part Number Qty  29  30  Drive Unit BC4401DW S/N 60200000 and up 31   32  Engine Unit BC4401DW S/N 60200000 and up 33  Limited Warranty Garantie limitée Zenoah AMERICA, INC