Zenoah BC3401DL manual  14 , Fueling the Unit, For Your Engine LIFE, Avoid

Page 14

Fuel

again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture.

5.Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers.

6.Indicate the contents on outside of container for easy identification.

FUELING THE UNIT

1.Untwist and remove the fuel cap. Rest the cap on a dustless place.

2.Put fuel into the fuel tank to 80% of the full capacity.

3.Fasten the fuel cap securely and wipe up any fuel spillage around the unit.

WARNING

1.Select bare ground for fueling.

2.Move at least 10feet (3meters) away from the fueling point before starting the engine.

3.Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container.

FOR YOUR ENGINE LIFE, AVOID;

1.FUEL WITH NO OIL(RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly.

2.GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication.

3.OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking.

4.Mixed fuels which have been left unused for a period of one month or more may clog the carburetor and result in the engine failing to operate properly.

5.In the case of storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel.

6.In the case of scrapping the used mixed oil container, scrap it only at an authorized repository site.

NOTE

As lot details of quality assurance, read the description in the section Limited Warranty carefully. Moreover, normal wear and change in product with no functional influence are not covered by the warranty. Also, be careful that, if the usage in the instruction manual is not observed as to the mixed gasoline, etc. described therein, it may not be covered by the warranty.

14

Image 14
Contents BC3401DL BC4401DW 848-G6D-93A2Safety First Contents BC3401DL Specifications 4  BC4401DWEmission control label  5 Safety Precautions  6  7  Work gear and clothing 8  Things to check before using your brushcutterAvoid Noise Problem Things to check before starting up the engineThings to be careful about when using your brushcutter  9  10  Set Up  11 Putting on Waist PAD BC4401DW only Installing Cutting Head 12  Fuel When using RedMax/ZENOAH genuine oilHOW to MIX Fuel  13 For Your Engine LIFE, Avoid  14 Fueling the Unit Starting Engine Operation 15   16  Optional Blade Usage  17 Bracket Handle  18 OPT3 OPT4 For BC3401DL OPT5 OPT6 Cutting MethodOperation  19 OPT7 OPT8 What causes blade thrust  20 Controlling Blade Bounce How you can reduce the chance of blade thrustOPT9 Maintenance Blade 21  How you can maintain the best controlRefilling Trimming Line Maintenance 22  AIR Filter 23  Disposal Procedures to be Performed After Every 100 Hours of USEStorage  24 Parts List  25 Drive Unit BC3401DL S/N 60200000 and up  26  27  Engine Unit BC3401DL S/N 60200000 and up  28  29  Description Part Number QtyDrive Unit BC4401DW S/N 60200000 and up  30  31  Engine Unit BC4401DW S/N 60200000 and up  32  33  Limited Warranty Garantie limitée Zenoah AMERICA, INC