Zenoah HEZ2610F-CA manual Handling Fuel, Refill after cooling the engine, Transportation

Page 16

English

5. For safe operation

manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance.

5.Do not use any accessory or attachment other than those bearing the RedMax mark and recommended for the unit.

6.Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming unable to operate properly.

HANDLING FUEL

1.The engine of the RedMax product is designed to run on a mixed fuel which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.

2.Never smoke while operating the unit or refilling its fuel tank.

3.When refilling the tank, always turn off the engine and allow it to cool down. Take a careful look around to make sure that there are no sparks or open flames anywhere nearby before refueling.

(1) Refill after cooling the engine

4.Wipe spilled fuel completely using a dry rag if any fuel spillage occurs during refueling.

5.After refueling, screw the fuel cap back tightly onto the fuel tank and then carry the unit to a spot 10feet (3m) or more away from where it was refueled before turning on the engine.

TRANSPORTATION

1.When hand-carrying the product, cover over the cutting part if necessary, lift up the product and carry it paying attention to the blade.

2.Never transport the product over rough roads over long distances by vehicle without removing all fuel from the fuel tank. If doing so, fuel might leak from the tank during transport.

16

Image 16
Contents HEZ2610F-CA Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Parts location SpecificationsHEZ2610F/HEZ2610F-CA Fiche technique Emplacement des pieces Situación de las piezasEspecificaciohes Symbols on the machine PositionEmplacement PosiciónWorking Condition For safe operationWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoDE LA Machine Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineDemarrage DU Moteur Arranque DEL MotorUtilisation DE LA Machine USO DEL ProductoMaintenance If Someone ComesSI QUELQU’UN S’APPROCHE EntretienSI Alguien SE Aproxima MantenimientoRefill after cooling the engine Handling FuelTransportation Manipulation DU Carburant TransportManipulación DEL Combustible Llenar una vez que el motor se haya enfriadoSet up SE1 Mounting Other PartsScrew Clamp bolt Tightning Torque 52~69in-lbs 6~8N.m SE2Assemblage Montaje Montage D’AUTRES PiecesVis Boulon d’ablocage Couple de serrage 52~69in-lbs 6~8N.m Montaje DE Otras PartesFuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Adjusting Wheel Height OperationOP1 OP2 OP3 OP4Fonctionnement Uso Reglage DE LA Hauteur DE LA RoueAjuste DE LA Altura DE LA Rueda Mise EN Marche DU MoteurAdjusting Throttle Cable Adjusting Idling Speed OP7OP5 OP6 OP7Arret DU Moteur OP4 Reglage Câble D’ACCÉLÉRATEURReglage DU Ralenti OP7 Cómo Parar EL Motor OP4HOW to USE OP8Fonctionnement Uso Comment Utiliser LE COUPE-BORDURES Como UsarMaintenance Be Sure to Check the Following Before Using Your Stick EdgerEntretien MantenimientoMaintenance Chart Tableau D’ENTRETIEN MantenimientoTabla DE Mantenimiento Replacement Plug is a NGK CMR7H MA1 MA2 MA3AIR Filter Fuel FilterEntretien Mantenimiento Muffler MA4 MA5 MA6 Spark ArresterSpark arrester Gear CaseCaja DE Cambios PARE-ETINCELLESCarter D’ENGRENAGE Arbre DE Transmission MA6Intake AIR Cooling Vent MA8 MA7 Blade MA7Cylinder Intake air cooling vent back Ouïe DU Refroidissement PAR AIR Cuchilla MA7Toma DE Aire DE Refrigeración Procedures to be Performed After Every 100 Hours of USE StorageDisposal MA9Mise au rebut Eliminación Rangement AlmacenamientoProtecteur 12. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes HEZ2610F HEZ2610F-CA NotaParts list Pipe Comp Parts list Cylinder Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control Mesures DE Lutte Contre LES EmissionsControl DE Emisiones HEZ2610F-CA