Zenoah HEZ2602S manual Handling Fuel, Refill after cooling the engine, Transportation

Page 16

English

5. For safe operation

manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance.

5.Do not use any accessory or attachment other than those bearing the RedMax mark and recommended for the unit.

6.Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming unable to operate properly.

■HANDLING FUEL

1.The engine of the RedMax product is designed to run on a mixed fuel which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.

2.Never smoke while operating the unit or refilling its fuel tank.

3.When refilling the tank, always turn off the engine and allow it to cool down. Take a careful look around to make sure that there are no sparks or open flames anywhere nearby before refueling.

(1) Refill after cooling the engine

4.Wipe spilled fuel completely using a dry rag if any fuel spillage occurs during refueling.

5.After refueling, screw the fuel cap back tightly onto the fuel tank and then carry the unit to a spot 10feet (3m) or more away from where it was refueled before turning on the engine.

■TRANSPORTATION

1.When hand-carrying the product, cover over the cutting part if necessary, lift up the product and carry it paying attention to the blade.

2.Never transport the product over rough roads over long distances by vehicle without removing all fuel from the fuel tank. If doing so, fuel might leak from the tank during transport.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents HEZ2602S Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Specifications Parts locationEmplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes HEZ2602SPosition Symbols on the machineEmission Control Posición EmplacementControl DE Emisiones Working Condition For safe operationWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoDE LA Machine Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineArranque DEL Motor Demarrage DU MoteurUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI QUELQU’UN S’APPROCHE EntretienSI Alguien SE Aproxima MantenimientoRefill after cooling the engine Handling FuelTransportation Manipulation DU Carburant TransportManipulación DEL Combustible Llenar una vez que el motor se haya enfriadoSet up SE1 Mounting Other PartsScrew Clamp bolt Tightning Torque 70~130 in-lb 8~15 N.m SE2Assemblage Montaje Montage D’AUTRES Pieces Montaje DE Otras PartesFuel When using Zenoah genuine oilRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile Zenoah Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Aceite Para USO EN Motores DE 4-TIEMPOS Adjusting Wheel Height OperationOP1 OP2 OP3 OP4Fonctionnement Uso Couple de serrage 51~68 in-lbs 6~8 N.mPar de torsión de apriete 51~68 in-lbs 6~8 N.m Mise EN Marche DU MoteurAdjusting Throttle Cable Adjusting Idling Speed OP7OP5 OP6 OP7Arret DU Moteur OP4 Reglage Câble D’ACCÉLÉRATEURReglage DU Ralenti OP7 Cómo Parar EL Motor OP4HOW to USE OP8Remarque Nota Comment Utiliser LE COUPE-BORDURES Como UsarMaintenance Be Sure to Check the Following Before Using Your Stick EdgerEntretien MantenimientoMaintenance Chart Tableau D’ENTRETIEN MantenimientoTabla DE Mantenimiento Replacement Plug is a NGK CMR7H MA1 MA2 MA3AIR Filter Fuel FilterEntretien Mantenimiento Muffler MA4 MA5 Spark ArresterSpark arrester Gear CaseCaja DE Cambios PARE-ETINCELLESCarter D’ENGRENAGE ParachispasIntake AIR Cooling Vent MA7 MA6 Blade MA6Cylinder Intake air cooling vent back Ouïe DU Refroidissement PAR AIR Toma DE Aire DE RefrigeraciónMA9 Procedures to be Performed After Every 100 Hours of USE StorageMA8 Protector Protector BoltProcedure a Effectuer Toutes LES Heures D’UTILISATION Entretien MantenimientoRangement Almacenamiento Protecteur Protector11. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes HEZ2602S NotaParts list Pipe Comp Engine Unit HEZ2602S S/N 60800001 and up Cylinder Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty RedMax Garantie limitée Garantía Limitada Komatsu Zenoah America INC

HEZ2602S specifications

The Zenoah HEZ2602S is a versatile and high-performance handheld power tool that excels in various outdoor maintenance tasks. Designed for both professionals and homeowners, this robust machine stands out in the market for its advanced features, technology, and reliability.

One of the primary features of the Zenoah HEZ2602S is its powerful engine. Equipped with a 26cc two-stroke engine, it delivers impressive power while maintaining fuel efficiency. This engine is engineered to provide optimal torque and speed, allowing users to tackle tough jobs with ease. Additionally, the machine features a low-emission system that complies with environmental regulations, making it a responsible choice for eco-conscious users.

The HEZ2602S is known for its lightweight design, which enhances maneuverability and reduces user fatigue during prolonged use. Weighing in at just 5.5 kg, this tool is easy to handle, making it suitable for both detailed tasks and larger areas. The ergonomic handle design contributes to comfort, granting users better control and reducing vibrations.

Another significant characteristic of the Zenoah HEZ2602S is its technologically advanced starting system. The machine is equipped with an easy start feature that allows users to start the engine with minimal effort. This technology significantly reduces the amount of pull force required, ensuring that the tool is ready to go when you are.

The HEZ2602S is a multi-functional tool, compatible with various attachments, including grass trimmers, brush cutters, and hedge trimmers. This versatility allows users to switch between tasks seamlessly, making it an essential tool for gardening, landscaping, and maintenance work.

Durability is also a key characteristic of the Zenoah HEZ2602S. Built with high-quality materials and components, it is designed to withstand the rigors of outdoor use. The robust construction ensures a long service life, providing excellent value for investment.

In summary, the Zenoah HEZ2602S is a powerful, lightweight, and versatile handheld power tool that offers excellent performance for various outdoor tasks. With its advanced engine technology, easy starting system, and compatibility with multiple attachments, it is well-suited for both professional landscapers and DIY enthusiasts. Its durable build and ergonomic design further cement its status as a reliable choice for outdoor maintenance.
Top Page Image Contents