Zenoah HEZ2602S manual If Someone Comes, Maintenance

Page 14

English

5. For safe operation

1.Grip the handles firmly with both hands using your whole hand. Place your feet slightly apart (slightly further apart than the width of your shoulders) so that your weight is distributed evenly across both legs, and always be sure to maintain a steady, even posture while working.

2.Keep cutting attachment below waist level.

3.Maintain the speed of the engine at the level required to perform cutting work, and never raise the speed of the engine above the level necessary.

4.If the unit start to shake or vibrate, turn off the engine and check the whole unit. Do not use it until the trouble has been properly corrected.

5.Keep all parts of your body away from rotating cutting attachment and hot surfaces.

6.Never touch the muffler, spark plug, or other metallic parts of the engine while the engine is in operation or immediately after shutting down the engine. Doing so could result in serious burns or electrical shock.

• IF SOMEONE COMES

1.Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris.

2.If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around.

■MAINTENANCE

1.In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual at regular intervals.

2.Always be sure to turn off the engine before performing any maintenance or checking procedures.

(1) Check ok !

WARNING

The metallic parts reach high temperatures immediately after stopping the engine.

3.When replacing the cutting attachment or any other part, or when replacing the oil or any lubricant, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax product.

4.In the event that any part must be replaced or any maintenance or repair work not described in this

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents HEZ2602S Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido Specifications Parts locationEspecificaciohes Emplacement des pieces Situación de las piezasFiche technique HEZ2602SEmission Control Symbols on the machinePosition Control DE Emisiones EmplacementPosición Working Circumstance For safe operationWorking Condition Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail PrecaucionesWorking Plan Before Starting the EngineDE LA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineUtilisation DE LA Machine USO DEL Producto Demarrage DU MoteurArranque DEL Motor Maintenance If Someone ComesSI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien MantenimientoTransportation Handling FuelRefill after cooling the engine Manipulación DEL Combustible Manipulation DU CarburantTransport Llenar una vez que el motor se haya enfriadoScrew Clamp bolt Tightning Torque 70~130 in-lb 8~15 N.m Set upSE1 Mounting Other Parts SE2Assemblage Montaje Montage D’AUTRES Pieces Montaje DE Otras PartesRecommended Mixing Ratio Gasoline 50OIL When using Zenoah genuine oilFuel Lors de l’utilisation de la véritable huile Zenoah Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFor Your Engine LIFE, Avoid HOW to MIX FuelFueling the Unit Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Aceite Para USO EN Motores DE 4-TIEMPOS OP1 Adjusting Wheel HeightOperation OP2 OP3 OP4Par de torsión de apriete 51~68 in-lbs 6~8 N.m Fonctionnement UsoCouple de serrage 51~68 in-lbs 6~8 N.m Mise EN Marche DU MoteurOP5 OP6 Adjusting Throttle CableAdjusting Idling Speed OP7 OP7Reglage DU Ralenti OP7 Arret DU Moteur OP4Reglage Câble D’ACCÉLÉRATEUR Cómo Parar EL Motor OP4HOW to USE OP8Remarque Nota Comment Utiliser LE COUPE-BORDURES Como UsarMaintenance Be Sure to Check the Following Before Using Your Stick EdgerEntretien MantenimientoMaintenance Chart Tabla DE Mantenimiento MantenimientoTableau D’ENTRETIEN AIR Filter Replacement Plug is a NGK CMR7HMA1 MA2 MA3 Fuel FilterEntretien Mantenimiento Spark arrester Muffler MA4 MA5Spark Arrester Gear CaseCarter D’ENGRENAGE Caja DE CambiosPARE-ETINCELLES ParachispasCylinder Intake air cooling vent back MA6 Blade MA6Intake AIR Cooling Vent MA7 Ouïe DU Refroidissement PAR AIR Toma DE Aire DE RefrigeraciónMA8 Protector MA9 Procedures to be Performed After Every 100 Hours of USEStorage Protector BoltRangement Almacenamiento Procedure a Effectuer Toutes LES Heures D’UTILISATIONEntretien Mantenimiento Protecteur ProtectorGuide de localisation des pannes Troubleshooting guide11. Guía de localización y solución de problemas HEZ2602S NotaParts list Pipe Comp Engine Unit HEZ2602S S/N 60800001 and up Cylinder Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty RedMax Garantie limitée Garantía Limitada Komatsu Zenoah America INC

HEZ2602S specifications

The Zenoah HEZ2602S is a versatile and high-performance handheld power tool that excels in various outdoor maintenance tasks. Designed for both professionals and homeowners, this robust machine stands out in the market for its advanced features, technology, and reliability.

One of the primary features of the Zenoah HEZ2602S is its powerful engine. Equipped with a 26cc two-stroke engine, it delivers impressive power while maintaining fuel efficiency. This engine is engineered to provide optimal torque and speed, allowing users to tackle tough jobs with ease. Additionally, the machine features a low-emission system that complies with environmental regulations, making it a responsible choice for eco-conscious users.

The HEZ2602S is known for its lightweight design, which enhances maneuverability and reduces user fatigue during prolonged use. Weighing in at just 5.5 kg, this tool is easy to handle, making it suitable for both detailed tasks and larger areas. The ergonomic handle design contributes to comfort, granting users better control and reducing vibrations.

Another significant characteristic of the Zenoah HEZ2602S is its technologically advanced starting system. The machine is equipped with an easy start feature that allows users to start the engine with minimal effort. This technology significantly reduces the amount of pull force required, ensuring that the tool is ready to go when you are.

The HEZ2602S is a multi-functional tool, compatible with various attachments, including grass trimmers, brush cutters, and hedge trimmers. This versatility allows users to switch between tasks seamlessly, making it an essential tool for gardening, landscaping, and maintenance work.

Durability is also a key characteristic of the Zenoah HEZ2602S. Built with high-quality materials and components, it is designed to withstand the rigors of outdoor use. The robust construction ensures a long service life, providing excellent value for investment.

In summary, the Zenoah HEZ2602S is a powerful, lightweight, and versatile handheld power tool that offers excellent performance for various outdoor tasks. With its advanced engine technology, easy starting system, and compatibility with multiple attachments, it is well-suited for both professional landscapers and DIY enthusiasts. Its durable build and ergonomic design further cement its status as a reliable choice for outdoor maintenance.
Top Page Image Contents