Sony specifications MDS-JE770 Section Service Notes, Flexible Circuit Board Repairing

Page 5

MDS-JE770

SECTION 1

SERVICE NOTES

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body.

During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts.

The flexible board is easily damaged and should be handled with care.

NOTES ON LASER DIODE EMISSION CHECK

Never look into the laser diode emission from right above when checking it for adjustment. It is feared that you will lose your sight.

Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.

This appliance is classified as a CLASS 1 LASER product. The

CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.

This caution label is located inside the unit.

Notes on chip component replacement

•Never reuse a disconnected chip component.

•Notice that the minus side of a tantalum capacitor may be damaged by heat.

Flexible Circuit Board Repairing

•Keep the temperature of soldering iron around 270˚C during repairing.

•Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

•Be careful not to apply force on the conductor when soldering or unsoldering.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radia- tion exposure.

5

Image 5

Contents 873-890-11 SpecificationsMDS-S50 MDM-7ASupplied accessories Genera l Power requirementsMDS-JE770 SELF-DIAGNOSIS FunctionItems of Error History Mode Items and Contents Disassembly Table of ContentsDiagrams Exploded ViewsFlexible Circuit Board Repairing MDS-JE770 Section Service NotesIOP JIG for Checking BD Board WaveformRecord Precedure Optical PICK-UP Block Type Discrimination KSN-260EMain Board Component Side Checks Prior to Parts Replacement and AdjustmentsForced Reset Bit Binary Retry Cause Display ModeHexadecimal Binary Bit When BinaryHigher Bits Lower Bits Hexa Details Button Descriptions MDS-JE770 Section GeneralDisassembly Flow MDS-JE770 Section DisassemblyFront Panel Section Two screws Main BoardOver Light Head HR901, BD Board Mechanism Deck Section MDM-7ALoading Motor Assy M103 Holder AssyOptical PICK-UP Sled Motor Assy M102, SliderSpindle Moter Assy M101 Precautions for USE of Test Mode MDS-JE770 Section Test ModeSetting the Test Mode Exiting the Test ModeSelecting the Test Mode MENU/NO Operating the Continuous Playback ModeMode display Test Mode DisplaysError rate display Functions of Other ButtonsMeanings of Other Displays When Memory NG is DisplayedAutomatic SELF-DIAGNOSIS Function InformationCheck before replacement MDS-JE770 Section Electrical AdjustmentsParts Replacement and Adjustment Auto Gain Control Output Level Adjustment flowPrecautions for USE of Optical PICK- UP KMS-260B/260E Precautions for Checking Laser Diode EmissionPrecautions for Adjustments Temp AdjustChecks Prior to Repairs Using the Continuously Recorded DiscOther Checks Auto CheckTraverse Check Traverse WaveformCD Error Rate Check Play Check MO Error Rate CheckFocus Bias Check Self-Recording/playback CheckLaser Power Adjustment Initial Setting of Adjustment ValueTemperature Compensation Offset Adjutment Iop NV Save Traverse AdjustmentFocus Bias Adjustment Auto Gain Control Output Level Adjustment Error Rate CheckCD Auto Gain Control Output Level Adjustment MO Auto Gain Control Output Level AdjustmentAdjusting Points and Connecting Points Circuit Boards Location MDS-JE770 Section DiagramsFor printed wiring boards For schematic diagramsBD Board Main BoardIC190 Block Diagrams BD SectionIC171 IC1 2/2 Main SectionIC360 2/2 Semiconductor SemiconductorOVEROptical Pick UP Block Write HeadBoard Board Main Main Schematic Diagram Main /2 See page 51 for IC Block Diagrams IC1 Model is printed on diagramKB Board Display BoardKEY-SW Board HP BoardLED Drive Schematic Diagram Display SectionC951 C952 RY910D910 CN921 C924 LF900 C910Main Schematic Diagram Power SectionIC101 CXA2523AR BD Board IC Block DiagramsIC500 AK4524 Main Board Pin No Pin Name Description IC PIN Function DescriptionIC101 CXA2523AR RF Amplifier BD Board Pin No Pin Name Desription Asyo MvciAsyi AvddFfdr TfdrFrdr FS4ADA.RESET IIC PowerFldt FlckEPN ADA. LatchDINT1/H Clip ProtectSTB TimerBeep SW REC FlcsVDISP1 ResetVFL1 OSC0Chassis Section Section Exploded ViewsNot supplied Supplied with J790 FL750 With RV790 FL750 1-517-987-11 Indicator TUBE, FluorescentMechanism MDM-7A Motor ASSY, Spindle HEAD, Over LightMotor ASSY, Sled Motor ASSY, LoadingMDS-JE770 Section Electrical Parts List Metal Chip SwitchJumper Resistor ShortMDS-JE770 Display HP KB KEY-SW KEY-SW Main MDS-JE770 Main 2SD2144S-TP-UVW Resistor VOL-SEL MDS-JE770 Main PTMemo MDS-JE770 Revision History