Sony MDS-JE770 Meanings of Other Displays, Automatic SELF-DIAGNOSIS Function, Information

Page 24

MDS-JE770

4-8. MEANINGS OF OTHER DISPLAYS

Display

 

Contents

When Lit

When Off

 

G

Servo ON

Servo OFF

X

Tracking servo OFF

Tracking servo ON

REC

Recording mode ON

Recording mode OFF

SYNC

CLV low speed mode

CLV normal mode

L.SYNC

ABCD adjustment completed

 

OVER

Tracking offset cancel ON

Tracking offset cancel OFF

B/1

Tracking auto gain OK

 

A-/REP

Focus auto gain OK

 

REC MODE

Pit

Groove

DISC/LP2

High reflection

Low reflection

SLEEP/SHUF

CLV S

CLV A

MONO

CLV LOCK

CLV UNLOCK

4-9. AUTOMATIC SELF-DIAGNOSIS FUNCTION

This test mode performs CREC and CPLAY automatically for mainly checking the characteristics of the optical pick-up. To perform this test mode, the laser power must first be checked.

Perform AUTO CHECK after the laser power check and Iop compare.

Procedure

1.Press the YES button. If “LDPWR ” is displayed, it means that the laser power check has not been performed. In this case, perform the laser power check and Iop compare, and then repeat from step 1.

2.If a disc is in the mechanical deck, it will be ejected forcibly.

“DISC IN” will be displayed in this case. Load a test disc (MDW-74/GA-1) which can be recorded.

3.If a disk is loaded at step 2, the check will start automatically.

4.When “XX CHECK” is displayed, the item corresponding to XX will be performed.

When “06 CHECK” completes, the disc loaded at step 2 will be ejected. “DISC IN” will be displayed. Load the check disc (MD) TDYS-1.

5.When the disc is loaded in step 4, the check will automatically be resumed from “07 CHECK”.

6.After completing to test item 12, check OK or NG will be displayed. If all items are OK, “CHECK ALL OK” will be displayed. If any item is NG, it will be displayed as “NG:xxxx”.

When “CHECK ALL OK” is displayed, it means that the optical pick-up is normal. Check the operations of the other spindle motor, thread motor, etc.

When displayed as “NG:xxxx”, it means that the optical pick-up is faulty. In this case, replace the optical pick-up.

4-10. INFORMATION

Display the software version.

Procedure

1.If displayed as “INFORMATION”, press the YES button.

2.The software version will be displayed.

3.Press the MENU/NO button to end this mode.

4-11. WHEN MEMORY NG IS DISPLAYED

If the nonvolatile memory data is abnormal, “E001”/”MEMORY NG” will be displayed so that the MD deck does not continue operations. In this case, set the test mode promptly and perform the following procedure.

Procedure

1.Set the test mode. (Refer to 4-2.)

2.Normally a message for selecting the test mode will be displayed. However if the nonvolatile memory is abnormal, the following will be displayed. “INIT EEP?”

3.Press the x button and A EJECT button together.

4.Rotate the lAMS L knob and select MDM-7A.

5.Press the lAMS L knob. If the nonvolatile memory is successfully overwritten, the normal test mode will be set and a message to select the test mode will be displayed.

Note: When this setting is doing, readjustment is necessary. (Adjustment it same as IC195 exchanged)

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Specifications 873-890-11MDS-S50 MDM-7AGenera l Power requirements Supplied accessoriesMDS-JE770 SELF-DIAGNOSIS FunctionItems of Error History Mode Items and Contents Table of Contents DisassemblyDiagrams Exploded ViewsMDS-JE770 Section Service Notes Flexible Circuit Board RepairingJIG for Checking BD Board Waveform IOPRecord Precedure KSN-260E Optical PICK-UP Block Type DiscriminationChecks Prior to Parts Replacement and Adjustments Forced ResetMain Board Component Side Retry Cause Display Mode Bit BinaryBit When Binary Higher Bits Lower Bits Hexa DetailsHexadecimal Binary MDS-JE770 Section General Button DescriptionsMDS-JE770 Section Disassembly Disassembly FlowFront Panel Section Main Board Two screwsMechanism Deck Section MDM-7A Over Light Head HR901, BD BoardHolder Assy Loading Motor Assy M103Sled Motor Assy M102, Slider Optical PICK-UPSpindle Moter Assy M101 MDS-JE770 Section Test Mode Precautions for USE of Test ModeSetting the Test Mode Exiting the Test ModeSelecting the Test Mode Operating the Continuous Playback Mode MENU/NOTest Mode Displays Mode displayError rate display Functions of Other ButtonsWhen Memory NG is Displayed Meanings of Other DisplaysAutomatic SELF-DIAGNOSIS Function InformationMDS-JE770 Section Electrical Adjustments Parts Replacement and AdjustmentCheck before replacement Adjustment flow Auto Gain Control Output LevelPrecautions for Checking Laser Diode Emission Precautions for USE of Optical PICK- UP KMS-260B/260EPrecautions for Adjustments Temp AdjustUsing the Continuously Recorded Disc Checks Prior to RepairsAuto Check Other ChecksTraverse Check Traverse WaveformPlay Check MO Error Rate Check CD Error Rate CheckFocus Bias Check Self-Recording/playback CheckInitial Setting of Adjustment Value Temperature Compensation Offset AdjutmentLaser Power Adjustment Traverse Adjustment Iop NV SaveFocus Bias Adjustment Error Rate Check Auto Gain Control Output Level AdjustmentCD Auto Gain Control Output Level Adjustment MO Auto Gain Control Output Level AdjustmentAdjusting Points and Connecting Points MDS-JE770 Section Diagrams Circuit Boards LocationFor schematic diagrams For printed wiring boardsBD Board Main BoardBlock Diagrams BD Section IC171IC190 Main Section IC360 2/2IC1 2/2 SemiconductorOVER SemiconductorOptical Pick UP Block Write HeadBoard Board Main Main Schematic Diagram Main /2 See page 51 for IC Block Diagrams Model is printed on diagram IC1Display Board KB BoardKEY-SW Board HP BoardSchematic Diagram Display Section LED DriveRY910 C951 C952D910 CN921 C924 LF900 C910Schematic Diagram Power Section MainIC Block Diagrams IC101 CXA2523AR BD BoardIC500 AK4524 Main Board IC PIN Function Description IC101 CXA2523AR RF Amplifier BD BoardPin No Pin Name Description Pin No Pin Name Desription Mvci AsyoAsyi AvddTfdr FfdrFrdr FS4IIC Power ADA.RESETFldt FlckADA. Latch EPNDINT1/H Clip ProtectTimer STBBeep SW REC FlcsReset VDISP1VFL1 OSC0Section Exploded Views Chassis SectionFL750 1-517-987-11 Indicator TUBE, Fluorescent Not supplied Supplied with J790 FL750 With RV790Mechanism MDM-7A HEAD, Over Light Motor ASSY, SpindleMotor ASSY, Sled Motor ASSY, LoadingMDS-JE770 Section Electrical Parts List Switch Metal ChipJumper Resistor ShortMDS-JE770 Display HP KB KEY-SW KEY-SW Main MDS-JE770 Main 2SD2144S-TP-UVW Resistor MDS-JE770 Main PT VOL-SELMemo MDS-JE770 Revision History
Top Page Image Contents